Hi Prabhakar,
On Tue, Sep 13, 2022 at 05:02:24PM +0100, Prabhakar wrote:
> From: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
>
> Convert the simple OV5645 Device Tree binding to json-schema.
>
> Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/media/i2c/ov5645.txt | 54 --------
> .../bindings/media/i2c/ovti,ov5645.yaml | 119 ++++++++++++++++++
> 2 files changed, 119 insertions(+), 54 deletions(-)
> delete mode 100644 Documentation/devicetree/bindings/media/i2c/ov5645.txt
> create mode 100644 Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml
>
> diff --git a/Documentation/devicetree/bindings/media/i2c/ov5645.txt b/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> deleted file mode 100644
> index 72ad992f77be..000000000000
> --- a/Documentation/devicetree/bindings/media/i2c/ov5645.txt
> +++ /dev/null
> @@ -1,54 +0,0 @@
> -* Omnivision 1/4-Inch 5Mp CMOS Digital Image Sensor
> -
> -The Omnivision OV5645 is a 1/4-Inch CMOS active pixel digital image sensor with
> -an active array size of 2592H x 1944V. It is programmable through a serial I2C
> -interface.
> -
> -Required Properties:
> -- compatible: Value should be "ovti,ov5645".
> -- clocks: Reference to the xclk clock.
> -- clock-names: Should be "xclk".
> -- clock-frequency: Frequency of the xclk clock.
> -- enable-gpios: Chip enable GPIO. Polarity is GPIO_ACTIVE_HIGH. This corresponds
> - to the hardware pin PWDNB which is physically active low.
> -- reset-gpios: Chip reset GPIO. Polarity is GPIO_ACTIVE_LOW. This corresponds to
> - the hardware pin RESETB.
> -- vdddo-supply: Chip digital IO regulator.
> -- vdda-supply: Chip analog regulator.
> -- vddd-supply: Chip digital core regulator.
> -
> -The device node must contain one 'port' child node for its digital output
> -video port, in accordance with the video interface bindings defined in
> -Documentation/devicetree/bindings/media/video-interfaces.txt.
> -
> -Example:
> -
> - &i2c1 {
> - ...
> -
> - ov5645: ov5645@3c {
> - compatible = "ovti,ov5645";
> - reg = <0x3c>;
> -
> - enable-gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
> - reset-gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&camera_rear_default>;
> -
> - clocks = <&clks 200>;
> - clock-names = "xclk";
> - clock-frequency = <24000000>;
> -
> - vdddo-supply = <&camera_dovdd_1v8>;
> - vdda-supply = <&camera_avdd_2v8>;
> - vddd-supply = <&camera_dvdd_1v2>;
> -
> - port {
> - ov5645_ep: endpoint {
> - clock-lanes = <1>;
> - data-lanes = <0 2>;
> - remote-endpoint = <&csi0_ep>;
> - };
> - };
> - };
> - };
> diff --git a/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml b/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml
> new file mode 100644
> index 000000000000..7f407c988f87
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/media/i2c/ovti,ov5645.yaml
> @@ -0,0 +1,119 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/media/i2c/ovti,ov5645.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: OmniVision OV5645 Image Sensor Device Tree Bindings
> +
> +maintainers:
> + - Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> +
> +allOf:
> + - $ref: /schemas/media/video-interface-devices.yaml#
> +
> +properties:
> + compatible:
> + const: ovti,ov5645
> +
> + reg:
> + maxItems: 1
> +
> + clocks:
> + description: XCLK Input Clock
> +
> + clock-names:
> + const: xclk
> +
> + clock-frequency:
> + description: Frequency of the xclk clock in Hz.
> +
> + vdda-supply:
> + description: Analog voltage supply, 2.8 volts
> +
> + vddd-supply:
> + description: Digital core voltage supply, 1.5 volts
> +
> + vdddo-supply:
> + description: Digital I/O voltage supply, 1.8 volts
> +
> + enable-gpios:
> + maxItems: 1
> + description:
> + Reference to the GPIO connected to the PWDNB pin, if any.
> +
> + reset-gpios:
> + maxItems: 1
> + description:
> + Reference to the GPIO connected to the RESETB pin, if any.
> +
> + port:
> + description: Digital Output Port
> + $ref: /schemas/graph.yaml#/$defs/port-base
> + additionalProperties: false
> +
> + properties:
> + endpoint:
> + $ref: /schemas/media/video-interfaces.yaml#
> + unevaluatedProperties: false
> +
> + properties:
> + clock-lanes:
> + const: 0
> +
> + bus-type:
> + const: 4
> +
> + data-lanes:
> + minItems: 1
> + maxItems: 2
> + items:
> + enum: [1, 2]
> +
> +required:
> + - compatible
> + - reg
> + - clocks
> + - clock-names
> + - clock-frequency
> + - vdda-supply
> + - vddd-supply
> + - vdddo-supply
> + - enable-gpios
> + - reset-gpios
> + - port
I think we don't need all of these properties as required.
The only "really" required are:
- compatible
- reg
- clocks
- port
Regards,
Tommaso
> +
> +additionalProperties: false
> +
> +examples:
> + - |
> + #include <dt-bindings/gpio/gpio.h>
> +
> + i2c {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + camera@3c {
> + compatible = "ovti,ov5645";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_ov5645>;
> + reg = <0x3c>;
> + clocks = <&clks 1>;
> + clock-names = "xclk";
> + clock-frequency = <24000000>;
> + vdddo-supply = <&ov5645_vdddo_1v8>; /* 1.8v */
> + vdda-supply = <&ov5645_vdda_2v8>; /* 2.8v */
> + vddd-supply = <&ov5645_vddd_1v5>; /* 1.5v */
> + enable-gpios = <&gpio1 19 GPIO_ACTIVE_HIGH>;
> + reset-gpios = <&gpio1 20 GPIO_ACTIVE_LOW>;
> +
> + port {
> + ov5645_ep: endpoint {
> + remote-endpoint = <&csi0_ep>;
> + clock-lanes = <0>;
> + data-lanes = <1 2>;
> + };
> + };
> + };
> + };
> +...
> --
> 2.25.1
>
--
Tommaso Merciai
Embedded Linux Engineer
tommaso.merciai@xxxxxxxxxxxxxxxxxxxx
__________________________________
Amarula Solutions SRL
Via Le Canevare 30, 31100 Treviso, Veneto, IT
T. +39 042 243 5310
info@xxxxxxxxxxxxxxxxxxxx
www.amarulasolutions.com
