Currently, Berlin SATA PHY driver assumes PHY_BASE address being
constant. While this PHY_BASE is correct for BG2Q, older BG2 PHY_BASE
is different. Prepare the driver for BG2 support by moving the phy_base
into private driver data.
Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@xxxxxxxxx>
---
Cc: Kishon Vijay Abraham I <kishon@xxxxxx>
Cc: "Antoine Ténart" <antoine.tenart@xxxxxxxxxxxxxxxxxx>
Cc: devicetree@xxxxxxxxxxxxxxx
Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
Cc: linux-kernel@xxxxxxxxxxxxxxx
---
drivers/phy/phy-berlin-sata.c | 42 ++++++++++++++++++++++++++++--------------
1 file changed, 28 insertions(+), 14 deletions(-)
diff --git a/drivers/phy/phy-berlin-sata.c b/drivers/phy/phy-berlin-sata.c
index 69ced52d72aa..9682b0f66177 100644
--- a/drivers/phy/phy-berlin-sata.c
+++ b/drivers/phy/phy-berlin-sata.c
@@ -30,7 +30,7 @@
#define MBUS_WRITE_REQUEST_SIZE_128 (BIT(2) << 16)
#define MBUS_READ_REQUEST_SIZE_128 (BIT(2) << 19)
-#define PHY_BASE 0x200
+#define BG2Q_PHY_BASE 0x200
/* register 0x01 */
#define REF_FREF_SEL_25 BIT(0)
@@ -61,15 +61,16 @@ struct phy_berlin_priv {
struct clk *clk;
struct phy_berlin_desc **phys;
unsigned nphys;
+ u32 phy_base;
};
-static inline void phy_berlin_sata_reg_setbits(void __iomem *ctrl_reg, u32 reg,
- u32 mask, u32 val)
+static inline void phy_berlin_sata_reg_setbits(void __iomem *ctrl_reg,
+ u32 phy_base, u32 reg, u32 mask, u32 val)
{
u32 regval;
/* select register */
- writel(PHY_BASE + reg, ctrl_reg + PORT_VSR_ADDR);
+ writel(phy_base + reg, ctrl_reg + PORT_VSR_ADDR);
/* set bits */
regval = readl(ctrl_reg + PORT_VSR_DATA);
@@ -103,17 +104,20 @@ static int phy_berlin_sata_power_on(struct phy *phy)
writel(regval, priv->base + HOST_VSA_DATA);
/* set PHY mode and ref freq to 25 MHz */
- phy_berlin_sata_reg_setbits(ctrl_reg, 0x1, 0xff,
- REF_FREF_SEL_25 | PHY_MODE_SATA);
+ phy_berlin_sata_reg_setbits(ctrl_reg, priv->phy_base, 0x01,
+ 0x00ff, REF_FREF_SEL_25 | PHY_MODE_SATA);
/* set PHY up to 6 Gbps */
- phy_berlin_sata_reg_setbits(ctrl_reg, 0x25, 0xc00, PHY_GEN_MAX_6_0);
+ phy_berlin_sata_reg_setbits(ctrl_reg, priv->phy_base, 0x25,
+ 0x0c00, PHY_GEN_MAX_6_0);
/* set 40 bits width */
- phy_berlin_sata_reg_setbits(ctrl_reg, 0x23, 0xc00, DATA_BIT_WIDTH_40);
+ phy_berlin_sata_reg_setbits(ctrl_reg, priv->phy_base, 0x23,
+ 0x0c00, DATA_BIT_WIDTH_40);
/* use max pll rate */
- phy_berlin_sata_reg_setbits(ctrl_reg, 0x2, 0x0, USE_MAX_PLL_RATE);
+ phy_berlin_sata_reg_setbits(ctrl_reg, priv->phy_base, 0x02,
+ 0x0000, USE_MAX_PLL_RATE);
/* set Gen3 controller speed */
regval = readl(ctrl_reg + PORT_SCR_CTL);
@@ -182,9 +186,22 @@ static u32 phy_berlin_power_down_bits[] = {
POWER_DOWN_PHY1,
};
+static u32 bg2q_sata_phy_base = BG2Q_PHY_BASE;
+
+static const struct of_device_id phy_berlin_sata_of_match[] = {
+ {
+ .compatible = "marvell,berlin2q-sata-phy",
+ .data = &bg2q_sata_phy_base,
+ },
+ { },
+};
+
static int phy_berlin_sata_probe(struct platform_device *pdev)
{
struct device *dev = &pdev->dev;
+ const struct of_device_id *match =
+ of_match_node(phy_berlin_sata_of_match, dev->of_node);
+ const u32 *phy_base = match->data;
struct device_node *child;
struct phy *phy;
struct phy_provider *phy_provider;
@@ -218,6 +235,8 @@ static int phy_berlin_sata_probe(struct platform_device *pdev)
if (!priv->phys)
return -ENOMEM;
+ priv->phy_base = *phy_base;
+
dev_set_drvdata(dev, priv);
spin_lock_init(&priv->lock);
@@ -264,11 +283,6 @@ static int phy_berlin_sata_probe(struct platform_device *pdev)
return 0;
}
-static const struct of_device_id phy_berlin_sata_of_match[] = {
- { .compatible = "marvell,berlin2q-sata-phy" },
- { },
-};
-
static struct platform_driver phy_berlin_sata_driver = {
.probe = phy_berlin_sata_probe,
.driver = {
--
2.1.1
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
