From: Jerome Neanne <jneanne@xxxxxxxxxxxx>
Add support fot the TI Power Management IC TPS65219
on the AM642 SKEVM board.
Needed for driver testing but official board support pending.
TI commitment is required before board upstream kick-off.
Signed-off-by: Jerome Neanne <jneanne@xxxxxxxxxxxx>
Signed-off-by: Markus Schneider-Pargmann <msp@xxxxxxxxxxxx>
---
arch/arm64/boot/dts/ti/k3-am642-sk.dts | 104 +++++++++++++++++++++++++
1 file changed, 104 insertions(+)
diff --git a/arch/arm64/boot/dts/ti/k3-am642-sk.dts b/arch/arm64/boot/dts/ti/k3-am642-sk.dts
index 2620469a7517..565b50810579 100644
--- a/arch/arm64/boot/dts/ti/k3-am642-sk.dts
+++ b/arch/arm64/boot/dts/ti/k3-am642-sk.dts
@@ -150,6 +150,20 @@ wlan_en: regulator-2 {
vin-supply = <&com8_ls_en>;
gpio = <&main_gpio0 48 GPIO_ACTIVE_HIGH>;
};
+
+ vsel_sd_nddr: gpio-regulator {
+ compatible = "regulator-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&vsel_sd_nddr_pins_default>;
+ regulator-name = "tps65219-LDO1-SEL-SD";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ vin-supply = <&ldo1_reg>;
+ gpios = <&main_gpio0 45 GPIO_ACTIVE_HIGH>;
+ states = <1800000 0x0>,
+ <3300000 0x1>;
+ };
};
&main_pmx0 {
@@ -181,6 +195,13 @@ AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0) /* (E19) USB0_DRVVBUS */
>;
};
+ main_i2c0_pins_default: main-i2c0-pins-default {
+ pinctrl-single,pins = <
+ AM64X_IOPAD(0x0260, PIN_INPUT_PULLUP, 0) /* (A18) I2C0_SCL */
+ AM64X_IOPAD(0x0264, PIN_INPUT_PULLUP, 0) /* (B18) I2C0_SDA */
+ >;
+ };
+
main_i2c1_pins_default: main-i2c1-pins-default {
pinctrl-single,pins = <
AM64X_IOPAD(0x0268, PIN_INPUT_PULLUP, 0) /* (C18) I2C1_SCL */
@@ -267,6 +288,12 @@ main_wlan_pins_default: main-wlan-pins-default {
AM64X_IOPAD(0x00bc, PIN_INPUT, 7) /* (U8) GPIO0_46 */
>;
};
+
+ vsel_sd_nddr_pins_default: vsel-sd-nddr-pins-default {
+ pinctrl-single,pins = <
+ AM64X_IOPAD(0x00b8, PIN_INPUT, 7) /* (Y7) PRG1_PRU0_GPO0.GPIO0_45 */
+ >;
+ };
};
&mcu_uart0 {
@@ -315,6 +342,83 @@ &mcu_i2c1 {
status = "disabled";
};
+&main_i2c0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&main_i2c0_pins_default>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ tps65219: pmic@30 {
+ compatible = "ti,tps65219";
+ reg = <0x30>;
+ system-power-controller;
+
+ buck1-supply = <&vcc_3v3_sys>;
+ buck2-supply = <&vcc_3v3_sys>;
+ buck3-supply = <&vcc_3v3_sys>;
+ ldo1-supply = <&vcc_3v3_sys>;
+ ldo2-supply = <&buck2_reg>;
+ ldo3-supply = <&vcc_3v3_sys>;
+ ldo4-supply = <&vcc_3v3_sys>;
+
+ regulators {
+ buck1_reg: buck1 {
+ regulator-name = "VDD_CORE";
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck2_reg: buck2 {
+ regulator-name = "VCC1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ buck3_reg: buck3 {
+ regulator-name = "VDD_LPDDR4";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo1_reg: ldo1 {
+ regulator-name = "VDDSHV_SD_IO_PMIC";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-allow-bypass;
+ };
+
+ ldo2_reg: ldo2 {
+ regulator-name = "VDDAR_CORE";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo3_reg: ldo3 {
+ regulator-name = "VDDA_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ ldo4_reg: ldo4 {
+ regulator-name = "VDD_PHY_2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+ };
+ };
+};
&main_i2c1 {
pinctrl-names = "default";
pinctrl-0 = <&main_i2c1_pins_default>;
--
2.37.2
