On Thu, Jul 21, 2022 at 10:51 PM AngeloGioacchino Del Regno
<angelogioacchino.delregno@xxxxxxxxxxxxx> wrote:
>
> As of now, all of the boards based on the cherry platform have a
> usable secondary SD/MMC controller, usually for SD cards: enable
> it to allow both booting from it and generally accessing external
> storage.
>
> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx>
> ---
> .../boot/dts/mediatek/mt8195-cherry.dtsi | 62 +++++++++++++++++++
> 1 file changed, 62 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi b/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi
> index 2853f7f76c90..8859957c7b27 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8195-cherry.dtsi
> @@ -17,6 +17,7 @@ aliases {
> i2c5 = &i2c5;
> i2c7 = &i2c7;
> mmc0 = &mmc0;
> + mmc1 = &mmc1;
> serial0 = &uart0;
> };
>
> @@ -227,6 +228,24 @@ &mmc0 {
> vqmmc-supply = <&mt6359_vufs_ldo_reg>;
> };
>
> +&mmc1 {
> + status = "okay";
> +
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cd-gpios = <&pio 54 GPIO_ACTIVE_LOW>;
> + max-frequency = <200000000>;
> + no-mmc;
> + no-sdio;
> + pinctrl-names = "default", "state_uhs";
> + pinctrl-0 = <&mmc1_pins_default>;
> + pinctrl-1 = <&mmc1_pins_uhs>;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + vmmc-supply = <&mt_pmic_vmch_ldo_reg>;
> + vqmmc-supply = <&mt_pmic_vmc_ldo_reg>;
> +};
> +
> /* for CPU-L */
> &mt6359_vcore_buck_reg {
> regulator-always-on;
> @@ -575,6 +594,49 @@ pins-rst {
> };
> };
>
> + mmc1_pins_default: mmc1-default-pins {
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
> + <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
> + <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
> + <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
> + <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
> + input-enable;
> + drive-strength = <8>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins-clk {
> + pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
> + drive-strength = <8>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
> +
> + pins-insert {
> + pinmux = <PINMUX_GPIO54__FUNC_GPIO54>;
> + bias-pull-up;
> + };
> + };
> +
> + mmc1_pins_uhs: mmc1-uhs-pins {
> + pins-cmd-dat {
> + pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
> + <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
> + <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
> + <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
> + <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
> + input-enable;
> + drive-strength = <8>;
> + bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
> + };
> +
> + pins-clk {
> + pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
> + drive-strength = <8>;
> + bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
> + };
I wonder if pins-insert should be duplicated here. And there's no
difference between the standard and UHS pinconfigs. One would expect
higher drive strength on the UHS set, if two sets were required.
So maybe we should just have one set, and use that one for both
the default and uhs states.
Otherwise,
Reviewed-by: Chen-Yu Tsai <wenst@xxxxxxxxxxxx>
Tested-by: Chen-Yu Tsai <wenst@xxxxxxxxxxxx>
> + };
> +
> nor_pins_default: nor-default-pins {
> pins-ck-io {
> pinmux = <PINMUX_GPIO142__FUNC_SPINOR_IO0>,
> --
> 2.35.1
>
>
