From: "Hui.Liu" <hui.liu@xxxxxxxxxxxx> This commit adds mt8188 compatible node in binding document. Signed-off-by: Hui.Liu <hui.liu@xxxxxxxxxxxx> --- .../bindings/pinctrl/pinctrl-mt8188.yaml | 306 ++++++++++++++++++ 1 file changed, 306 insertions(+) create mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-mt8188.yaml diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8188.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8188.yaml new file mode 100644 index 000000000000..43cc2424107f --- /dev/null +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8188.yaml @@ -0,0 +1,306 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/pinctrl/pinctrl-mt8188.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: MediaTek MT8188 Pin Controller + +maintainers: + - Sean Wang <sean.wang@xxxxxxxxxxxx> + +description: | + The MediaTek's Pin controller is used to control SoC pins. + +properties: + compatible: + const: mediatek,mt8188-pinctrl + + gpio-controller: true + + '#gpio-cells': + description: | + Number of cells in GPIO specifier. Since the generic GPIO binding is used, + the amount of cells must be specified as 2. See the below + mentioned gpio binding representation for description of particular cells. + const: 2 + + gpio-ranges: + description: gpio valid number range. + maxItems: 1 + + reg: + description: | + Physical address base for gpio base registers. There are 8 GPIO + physical address base in mt8188. + maxItems: 8 + + reg-names: + description: | + Gpio base register names. + maxItems: 8 + + interrupt-controller: true + + '#interrupt-cells': + const: 2 + + interrupts: + description: The interrupt outputs to sysirq. + maxItems: 1 + + mediatek,rsel_resistance_in_si_unit: + type: boolean + description: | + Identifying i2c pins pull up/down type which is RSEL. It can support + RSEL define or si unit value(ohm) to set different resistance. + +# PIN CONFIGURATION NODES +patternProperties: + '-pins$': + type: object + additionalProperties: false + patternProperties: + '^pins': + type: object + additionalProperties: false + description: | + A pinctrl node should contain at least one subnodes representing the + pinctrl groups available on the machine. Each subnode will list the + pins it needs, and how they should be configured, with regard to muxer + configuration, pullups, drive strength, input enable/disable and + input schmitt. + An example of using macro: + pincontroller { + /* GPIO0 set as multifunction GPIO0 */ + gpio-pins { + pins { + pinmux = <PINMUX_GPIO0__FUNC_B_GPIO0>; + } + }; + /* GPIO56 set as multifunction SDA0 */ + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>; + } + }; + }; + $ref: "pinmux-node.yaml" + + properties: + pinmux: + description: | + Integer array, represents gpio pin number and mux setting. + Supported pin number and mux varies for different SoCs, and are + defined as macros in dt-bindings/pinctrl/<soc>-pinfunc.h + directly. + + drive-strength: + enum: [2, 4, 6, 8, 10, 12, 14, 16] + + mediatek,drive-strength-adv: + description: | + Describe the specific driving setup property. + For I2C pins, the existing generic driving setup can only support + 2/4/6/8/10/12/14/16mA driving. But in specific driving setup, they + can support 0.125/0.25/0.5/1mA adjustment. If we enable specific + driving setup, the existing generic setup will be disabled. + The specific driving setup is controlled by E1E0EN. + When E1=0/E0=0, the strength is 0.125mA. + When E1=0/E0=1, the strength is 0.25mA. + When E1=1/E0=0, the strength is 0.5mA. + When E1=1/E0=1, the strength is 1mA. + EN is used to enable or disable the specific driving setup. + Valid arguments are described as below: + 0: (E1, E0, EN) = (0, 0, 0) + 1: (E1, E0, EN) = (0, 0, 1) + 2: (E1, E0, EN) = (0, 1, 0) + 3: (E1, E0, EN) = (0, 1, 1) + 4: (E1, E0, EN) = (1, 0, 0) + 5: (E1, E0, EN) = (1, 0, 1) + 6: (E1, E0, EN) = (1, 1, 0) + 7: (E1, E0, EN) = (1, 1, 1) + So the valid arguments are from 0 to 7. + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3, 4, 5, 6, 7] + + bias-pull-down: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt8188 pull down PUPD/R0/R1 type define value. + - enum: [200, 201, 202, 203, 204, 205, 206, 207] + description: mt8188 pull down RSEL type define value. + - enum: [75000, 5000] + description: mt8188 pull down RSEL type si unit value(ohm). + description: | + For pull down type is normal, it don't need add RSEL & R1R0 define + and resistance value. + For pull down type is PUPD/R0/R1 type, it can add R1R0 define to + set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & + "MTK_PUPD_SET_R1R0_11" define in mt8188. + For pull down type is RSEL, it can add RSEL define & resistance + value(ohm) to set different resistance by identifying property + "mediatek,rsel_resistance_in_si_unit". + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" + & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" + & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" + & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" + define in mt8188. It can also support resistance value(ohm) + "75000" & "5000" in mt8188. + + An example of using RSEL define: + pincontroller { + i2c0_pin { + pins { + pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>; + bias-pull-updown = <MTK_PULL_SET_RSEL_001>; + } + }; + }; + An example of using si unit resistance value(ohm): + &pio { + mediatek,rsel_resistance_in_si_unit; + } + pincontroller { + i2c0_pin { + pins { + pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>; + bias-pull-down = <75000>; + } + }; + }; + + bias-pull-up: + oneOf: + - type: boolean + - enum: [100, 101, 102, 103] + description: mt8188 pull up PUPD/R0/R1 type define value. + - enum: [200, 201, 202, 203, 204, 205, 206, 207] + description: mt8188 pull up RSEL type define value. + - enum: [1000, 1500, 2000, 3000, 4000, 5000, 10000, 75000] + description: mt8188 pull up RSEL type si unit value(ohm). + description: | + For pull up type is normal, it don't need add RSEL & R1R0 define + and resistance value. + For pull up type is PUPD/R0/R1 type, it can add R1R0 define to + set different resistance. It can support "MTK_PUPD_SET_R1R0_00" & + "MTK_PUPD_SET_R1R0_01" & "MTK_PUPD_SET_R1R0_10" & + "MTK_PUPD_SET_R1R0_11" define in mt8188. + For pull up type is RSEL, it can add RSEL define & resistance + value(ohm) to set different resistance by identifying property + "mediatek,rsel_resistance_in_si_unit". + It can support "MTK_PULL_SET_RSEL_000" & "MTK_PULL_SET_RSEL_001" + & "MTK_PULL_SET_RSEL_010" & "MTK_PULL_SET_RSEL_011" + & "MTK_PULL_SET_RSEL_100" & "MTK_PULL_SET_RSEL_101" + & "MTK_PULL_SET_RSEL_110" & "MTK_PULL_SET_RSEL_111" + define in mt8188. It can also support resistance value(ohm) + "1000" & "1500" & "2000" & "3000" & "4000" & "5000" & "10000" & + "75000" in mt8188. + An example of using RSEL define: + pincontroller { + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>; + bias-pull-up = <MTK_PULL_SET_RSEL_001>; + } + }; + }; + An example of using si unit resistance value(ohm): + &pio { + mediatek,rsel_resistance_in_si_unit; + } + pincontroller { + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO56__FUNC_B1_SDA0>; + bias-pull-up = <1000>; + } + }; + }; + + bias-disable: true + + output-high: true + + output-low: true + + input-enable: true + + input-disable: true + + input-schmitt-enable: true + + input-schmitt-disable: true + + required: + - pinmux + +allOf: + - $ref: "pinctrl.yaml#" + +required: + - compatible + - reg + - interrupts + - interrupt-controller + - '#interrupt-cells' + - gpio-controller + - '#gpio-cells' + - gpio-ranges + +additionalProperties: false + +examples: + - | + #include <dt-bindings/pinctrl/mt8188-pinfunc.h> + #include <dt-bindings/interrupt-controller/arm-gic.h> + # + pio: pinctrl@10005000 { + compatible = "mediatek,mt8188-pinctrl"; + reg = <0x10005000 0x1000>, + <0x11c00000 0x1000>, + <0x11e10000 0x1000>, + <0x11e20000 0x1000>, + <0x11ea0000 0x1000>, + <0x1000b000 0x1000>; + reg-names = "iocfg0", "iocfg_rm", + "iocfg_lt", "iocfg_lm", "iocfg_rt", + "eint"; + gpio-controller; + #gpio-cells = <2>; + gpio-ranges = <&pio 0 0 176>; + interrupt-controller; + interrupts = <GIC_SPI 225 IRQ_TYPE_LEVEL_HIGH 0>; + #interrupt-cells = <2>; + + pio-pins { + pins { + pinmux = <PINMUX_GPIO0__FUNC_B_GPIO0>; + output-low; + }; + }; + + spi0-pins { + pins-spi { + pinmux = <PINMUX_GPIO75__FUNC_O_SPIM1_CSB>, + <PINMUX_GPIO76__FUNC_O_SPIM1_CLK>, + <PINMUX_GPIO77__FUNC_B0_SPIM1_MOSI>; + bias-disable; + }; + pins-spi-mi { + pinmux = <PINMUX_GPIO78__FUNC_B0_SPIM1_MISO>; + bias-pull-down; + }; + }; + + i2c0-pins { + pins { + pinmux = <PINMUX_GPIO55__FUNC_B1_SCL0>, + <PINMUX_GPIO56__FUNC_B1_SDA0>; + bias-disable; + mediatek,drive-strength-adv = <7>; + }; + }; + }; -- 2.18.0
