In order to create a more sophisticated AHCI controller DT bindings let's divide the already available generic AHCI platform YAML schema into the platform part and a set of the common AHCI properties. The former part will be used to evaluate the AHCI DT nodes mainly compatible with the generic AHCI controller while the later schema will be used for more thorough AHCI DT nodes description. For instance such YAML schemas design will be useful for our DW AHCI SATA controller derivative with four clock sources, two reset lines, one system controller reference and specific max Rx/Tx DMA xfers size constraints. Note the phys and target-supply property requirement is preserved in the generic AHCI platform bindings because some platforms can lack of the explicitly specified PHYs or target device power regulators. Also note the SATA/AHCI ports properties have been moved to the $defs-paragraph of the schemas. It's done in order to create the extendable properties hierarchy such that particular AHCI-controller could add vendor-specific port properties. Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx> Reviewed-by: Rob Herring <robh@xxxxxxxxxx> --- Folks, I don't really see why the phys/target-supply requirement has been added to the generic AHCI DT schema in the first place. Probably just to imply some meaning for the sub-nodes definition. Anyway in one of the further patches I am adding the DW AHCI SATA controller DT bindings which won't require having these properties specified in the sub-nodes, but will describe additional port-specific properties. That's why I get to keep the constraints in the ahci-platform.yaml schema instead of moving them to the common schema. Changelog v2: - This is a new patch created after rebasing v1 onto the 5.18-rc3 kernel. Changelog v3: - Replace Jens's email address with Damien's one in the list of the schema maintainers. (@Damien) Changelog v4: - Drop clocks, clock-names, resets, reset-names and power-domains properties from the common schema. (@Rob) - Create sata/ahci-port properties definition hierarchy so the sub-schemas would inherit and extend the ports properties of the super-schema. (@Rob) --- .../devicetree/bindings/ata/ahci-common.yaml | 100 ++++++++++++++++++ .../bindings/ata/ahci-platform.yaml | 72 ++----------- .../devicetree/bindings/ata/sata-common.yaml | 8 +- 3 files changed, 115 insertions(+), 65 deletions(-) create mode 100644 Documentation/devicetree/bindings/ata/ahci-common.yaml diff --git a/Documentation/devicetree/bindings/ata/ahci-common.yaml b/Documentation/devicetree/bindings/ata/ahci-common.yaml new file mode 100644 index 000000000000..e89bda3b62cc --- /dev/null +++ b/Documentation/devicetree/bindings/ata/ahci-common.yaml @@ -0,0 +1,100 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/ata/ahci-common.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Common Properties for Serial ATA AHCI controllers + +maintainers: + - Hans de Goede <hdegoede@xxxxxxxxxx> + - Damien Le Moal <damien.lemoal@xxxxxxxxxxxxxxxxxx> + +description: + This document defines device tree properties for a common AHCI SATA + controller implementation. It's hardware interface is supposed to + conform to the technical standard defined by Intel (see Serial ATA + Advanced Host Controller Interface specification for details). The + document doesn't constitute a DT-node binding by itself but merely + defines a set of common properties for the AHCI-compatible devices. + +select: false + +allOf: + - $ref: sata-common.yaml# + +properties: + reg: + description: + Generic AHCI registers space conforming to the Serial ATA AHCI + specification. + + reg-names: + description: CSR space IDs + + interrupts: + description: + Generic AHCI state change interrupt. Can be implemented either as a + single line attached to the controller or as a set of the signals + indicating the particular port events. + + ahci-supply: + description: Power regulator for AHCI controller + + target-supply: + description: Power regulator for SATA target device + + phy-supply: + description: Power regulator for SATA PHY + + phys: + description: Reference to the SATA PHY node + maxItems: 1 + + phy-names: + maxItems: 1 + + ports-implemented: + $ref: '/schemas/types.yaml#/definitions/uint32' + description: + Mask that indicates which ports the HBA supports. Useful if PI is not + programmed by the BIOS, which is true for some embedded SoC's. + maximum: 0x1f + +patternProperties: + "^sata-port@[0-9a-f]+$": + $ref: '#/$defs/ahci-port' + description: + It is optionally possible to describe the ports as sub-nodes so + to enable each port independently when dealing with multiple PHYs. + +required: + - reg + - interrupts + +additionalProperties: true + +$defs: + ahci-port: + $ref: /schemas/ata/sata-common.yaml#/$defs/sata-port + + properties: + reg: + description: AHCI SATA port identifier + maxItems: 1 + + phys: + description: Individual AHCI SATA port PHY + maxItems: 1 + + phy-names: + description: AHCI SATA port PHY ID + maxItems: 1 + + target-supply: + description: Power regulator for SATA port target device + + required: + - reg + +... diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.yaml b/Documentation/devicetree/bindings/ata/ahci-platform.yaml index 9304e4731965..15be98e0385b 100644 --- a/Documentation/devicetree/bindings/ata/ahci-platform.yaml +++ b/Documentation/devicetree/bindings/ata/ahci-platform.yaml @@ -36,8 +36,7 @@ select: - compatible allOf: - - $ref: "sata-common.yaml#" - + - $ref: "ahci-common.yaml#" properties: compatible: @@ -69,90 +68,37 @@ properties: maxItems: 1 clocks: - description: - Clock IDs array as required by the controller. minItems: 1 maxItems: 3 clock-names: - description: - Names of clocks corresponding to IDs in the clock property. minItems: 1 maxItems: 3 interrupts: maxItems: 1 - ahci-supply: - description: - regulator for AHCI controller - - phy-supply: - description: - regulator for PHY power - - phys: - description: - List of all PHYs on this controller - maxItems: 1 - - phy-names: - description: - Name specifier for the PHYs - maxItems: 1 - - ports-implemented: - $ref: '/schemas/types.yaml#/definitions/uint32' - description: | - Mask that indicates which ports that the HBA supports - are available for software to use. Useful if PORTS_IMPL - is not programmed by the BIOS, which is true with - some embedded SoCs. - maximum: 0x1f - power-domains: maxItems: 1 resets: maxItems: 1 - target-supply: - description: - regulator for SATA target power - -required: - - compatible - - reg - - interrupts - patternProperties: "^sata-port@[0-9a-f]+$": - type: object - additionalProperties: false - description: - Subnode with configuration of the Ports. - - properties: - reg: - maxItems: 1 - - phys: - maxItems: 1 - - phy-names: - maxItems: 1 - - target-supply: - description: - regulator for SATA target power - - required: - - reg + $ref: /schemas/ata/ahci-common.yaml#/$defs/ahci-port anyOf: - required: [ phys ] - required: [ target-supply ] + unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + unevaluatedProperties: false examples: diff --git a/Documentation/devicetree/bindings/ata/sata-common.yaml b/Documentation/devicetree/bindings/ata/sata-common.yaml index cb88d3e25e73..5a31a902618d 100644 --- a/Documentation/devicetree/bindings/ata/sata-common.yaml +++ b/Documentation/devicetree/bindings/ata/sata-common.yaml @@ -35,9 +35,15 @@ properties: patternProperties: "^sata-port@[0-9a-e]$": + $ref: '#/$defs/sata-port' description: | DT nodes for ports connected on the SATA host. The SATA port nodes will be named "sata-port". + +additionalProperties: true + +$defs: + sata-port: type: object properties: @@ -49,6 +55,4 @@ patternProperties: multiplier making it possible to connect up to 15 disks to a single SATA port. -additionalProperties: true - ... -- 2.35.1
