Move wcd specific pin conf to common file to support various
herbronie variant boards and to avoid duplicate nodes in dts files.
Signed-off-by: Srinivasa Rao Mandadapu <quic_srivasam@xxxxxxxxxxx>
---
Changes Since V1:
-- Remove redundant documentation.
-- Update the pincontrol header comment.
.../dts/qcom/sc7280-herobrine-audio-wcd9385.dtsi | 64 ++++++++++++++++++++++
arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts | 61 ---------------------
2 files changed, 64 insertions(+), 61 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-wcd9385.dtsi b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-wcd9385.dtsi
index 32a1e78..859faaa 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-wcd9385.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-audio-wcd9385.dtsi
@@ -5,6 +5,70 @@
* Copyright (c) 2022, The Linux Foundation. All rights reserved.
*/
+/* PINCTRL */
+
+&lpass_dmic01_clk {
+ drive-strength = <8>;
+ bias-disable;
+};
+
+&lpass_dmic01_clk_sleep {
+ drive-strength = <2>;
+};
+
+&lpass_dmic01_data {
+ bias-pull-down;
+};
+
+&lpass_dmic23_clk {
+ drive-strength = <8>;
+ bias-disable;
+};
+
+&lpass_dmic23_clk_sleep {
+ drive-strength = <2>;
+};
+
+&lpass_dmic23_data {
+ bias-pull-down;
+};
+
+&lpass_rx_swr_clk {
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+};
+
+&lpass_rx_swr_clk_sleep {
+ bias-pull-down;
+};
+
+&lpass_rx_swr_data {
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+};
+
+&lpass_rx_swr_data_sleep {
+ bias-pull-down;
+};
+
+&lpass_tx_swr_clk {
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-disable;
+};
+
+&lpass_tx_swr_clk_sleep {
+ bias-pull-down;
+};
+
+&lpass_tx_swr_data {
+ drive-strength = <2>;
+ slew-rate = <1>;
+ bias-bus-hold;
+};
+
&mi2s1_data0 {
drive-strength = <6>;
bias-disable;
diff --git a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
index e9ca6c5..7881bbc 100644
--- a/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
+++ b/arch/arm64/boot/dts/qcom/sc7280-herobrine-crd.dts
@@ -155,67 +155,6 @@ ap_ts_pen_1v8: &i2c13 {
* - If a pin is totally internal to Qcard then it gets Qcard name.
* - If a pin is not hooked up on Qcard, it gets no name.
*/
-&lpass_dmic01_clk {
- drive-strength = <8>;
- bias-disable;
-};
-
-&lpass_dmic01_clk_sleep {
- drive-strength = <2>;
-};
-
-&lpass_dmic01_data {
- bias-pull-down;
-};
-
-&lpass_dmic23_clk {
- drive-strength = <8>;
- bias-disable;
-};
-
-&lpass_dmic23_clk_sleep {
- drive-strength = <2>;
-};
-
-&lpass_dmic23_data {
- bias-pull-down;
-};
-
-&lpass_rx_swr_clk {
- drive-strength = <2>;
- slew-rate = <1>;
- bias-disable;
-};
-
-&lpass_rx_swr_clk_sleep {
- bias-pull-down;
-};
-
-&lpass_rx_swr_data {
- drive-strength = <2>;
- slew-rate = <1>;
- bias-bus-hold;
-};
-
-&lpass_rx_swr_data_sleep {
- bias-pull-down;
-};
-
-&lpass_tx_swr_clk {
- drive-strength = <2>;
- slew-rate = <1>;
- bias-disable;
-};
-
-&lpass_tx_swr_clk_sleep {
- bias-pull-down;
-};
-
-&lpass_tx_swr_data {
- drive-strength = <2>;
- slew-rate = <1>;
- bias-bus-hold;
-};
&pm8350c_gpios {
gpio-line-names = "FLASH_STROBE_1", /* 1 */
--
2.7.4
