Re: [PATCH v4 1/5] dt-bindings: display: bridge: Convert cdns,dsi.txt to yaml

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Krzysztof,

On 10:17-20220706, Krzysztof Kozlowski wrote:
> On 05/07/2022 14:11, Rahul T R wrote:
> > Convert cdns,dsi.txt binding to yaml format
> > 
> > Signed-off-by: Rahul T R <r-ravikumar@xxxxxx>
> > ---
> >  .../bindings/display/bridge/cdns,dsi.txt      | 112 ----------
> >  .../bindings/display/bridge/cdns,dsi.yaml     | 198 ++++++++++++++++++
> >  2 files changed, 198 insertions(+), 112 deletions(-)
> >  delete mode 100644 Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
> >  create mode 100644 Documentation/devicetree/bindings/display/bridge/cdns,dsi.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
> > deleted file mode 100644
> > index 525a4bfd8634..000000000000
> > --- a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.txt
> > +++ /dev/null
> > @@ -1,112 +0,0 @@
> > -Cadence DSI bridge
> > -==================
> > -
> > -The Cadence DSI bridge is a DPI to DSI bridge supporting up to 4 DSI lanes.
> > -
> > -Required properties:
> > -- compatible: should be set to "cdns,dsi".
> > -- reg: physical base address and length of the controller's registers.
> > -- interrupts: interrupt line connected to the DSI bridge.
> > -- clocks: DSI bridge clocks.
> > -- clock-names: must contain "dsi_p_clk" and "dsi_sys_clk".
> > -- phys: phandle link to the MIPI D-PHY controller.
> > -- phy-names: must contain "dphy".
> > -- #address-cells: must be set to 1.
> > -- #size-cells: must be set to 0.
> > -
> > -Optional properties:
> > -- resets: DSI reset lines.
> > -- reset-names: can contain "dsi_p_rst".
> > -
> > -Required subnodes:
> > -- ports: Ports as described in Documentation/devicetree/bindings/graph.txt.
> > -  2 ports are available:
> > -  * port 0: this port is only needed if some of your DSI devices are
> > -	    controlled through  an external bus like I2C or SPI. Can have at
> > -	    most 4 endpoints. The endpoint number is directly encoding the
> > -	    DSI virtual channel used by this device.
> > -  * port 1: represents the DPI input.
> > -  Other ports will be added later to support the new kind of inputs.
> > -
> > -- one subnode per DSI device connected on the DSI bus. Each DSI device should
> > -  contain a reg property encoding its virtual channel.
> > -
> > -Example:
> > -	dsi0: dsi@fd0c0000 {
> > -		compatible = "cdns,dsi";
> > -		reg = <0x0 0xfd0c0000 0x0 0x1000>;
> > -		clocks = <&pclk>, <&sysclk>;
> > -		clock-names = "dsi_p_clk", "dsi_sys_clk";
> > -		interrupts = <1>;
> > -		phys = <&dphy0>;
> > -		phy-names = "dphy";
> > -		#address-cells = <1>;
> > -		#size-cells = <0>;
> > -
> > -		ports {
> > -			#address-cells = <1>;
> > -			#size-cells = <0>;
> > -
> > -			port@1 {
> > -				reg = <1>;
> > -				dsi0_dpi_input: endpoint {
> > -					remote-endpoint = <&xxx_dpi_output>;
> > -				};
> > -			};
> > -		};
> > -
> > -		panel: dsi-dev@0 {
> > -			compatible = "<vendor,panel>";
> > -			reg = <0>;
> > -		};
> > -	};
> > -
> > -or
> > -
> > -	dsi0: dsi@fd0c0000 {
> > -		compatible = "cdns,dsi";
> > -		reg = <0x0 0xfd0c0000 0x0 0x1000>;
> > -		clocks = <&pclk>, <&sysclk>;
> > -		clock-names = "dsi_p_clk", "dsi_sys_clk";
> > -		interrupts = <1>;
> > -		phys = <&dphy1>;
> > -		phy-names = "dphy";
> > -		#address-cells = <1>;
> > -		#size-cells = <0>;
> > -
> > -		ports {
> > -			#address-cells = <1>;
> > -			#size-cells = <0>;
> > -
> > -			port@0 {
> > -				reg = <0>;
> > -				#address-cells = <1>;
> > -				#size-cells = <0>;
> > -
> > -				dsi0_output: endpoint@0 {
> > -					reg = <0>;
> > -					remote-endpoint = <&dsi_panel_input>;
> > -				};
> > -			};
> > -
> > -			port@1 {
> > -				reg = <1>;
> > -				dsi0_dpi_input: endpoint {
> > -					remote-endpoint = <&xxx_dpi_output>;
> > -				};
> > -			};
> > -		};
> > -	};
> > -
> > -	i2c@xxx {
> > -		panel: panel@59 {
> > -			compatible = "<vendor,panel>";
> > -			reg = <0x59>;
> > -
> > -			port {
> > -				dsi_panel_input: endpoint {
> > -					remote-endpoint = <&dsi0_output>;
> > -				};
> > -			};
> > -		};
> > -	};
> > diff --git a/Documentation/devicetree/bindings/display/bridge/cdns,dsi.yaml b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.yaml
> > new file mode 100644
> > index 000000000000..ccedc73d8c18
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/display/bridge/cdns,dsi.yaml
> > @@ -0,0 +1,198 @@
> > +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/display/bridge/cdns,dsi.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Cadence DSI bridge
> > +
> > +maintainers:
> > +  - Boris Brezillon <boris.brezillon@xxxxxxxxxxx>
> > +
> > +description: |
> > +   CDNS DSI is a bridge device which converts DPI to DSI
> > +
> > +properties:
> > +  compatible:
> > +    items:
> 
> These are not items and it does not make any sense, because you remove
> it in second patch. Just make it an enum.
> 
> > +      - const: cdns,dsi
> > +
> > +  reg:
> > +    items:
> > +      - description:
> > +          Register block for controller's registers.
> > +
> > +  clocks:
> > +    items:
> > +      - description: PSM clock, used by the IP
> > +      - description: sys clock, used by the IP
> > +
> > +  clock-names:
> > +    items:
> > +      - const: dsi_p_clk
> > +      - const: dsi_sys_clk
> > +
> > +  phys:
> > +    maxItems: 1
> > +    description: phandle link to the MIPI D-PHY controller.
> > +
> > +  phy-names:
> > +    const: dphy
> > +
> > +  power-domains:
> > +    maxItems: 1
> 
> This was not present in old bindings and your commit msg says it is only
> a conversion.
> 

Thanks for the review !
I have sent a v5 with the fixes
please review

Regards
Rahul T R

> > +
> > +  interrupts:
> > +    maxItems: 1
> > +
> > +  resets:
> > +    maxItems: 1
> > +    description: PHY reset.
> > +
> > +  reset-names:
> > +    const: dsi_p_rst
> > +
> > +  ports:
> > +    $ref: /schemas/graph.yaml#/properties/ports
> > +
> > +    properties:
> > +      port@0:
> > +        $ref: /schemas/graph.yaml#/properties/port
> > +        description:
> > +          Output port representing the DSI output. It can have
> > +          most 4 endpoints. The endpoint number is directly encoding
> > +          the DSI virtual channel used by this device.
> > +
> > +      port@1:
> > +        $ref: /schemas/graph.yaml#/properties/port
> > +        description:
> > +          Input port representing the DP bridge input.
> > +
> > +    required:
> > +      - port@1
> > +
> > +allOf:
> > +  - $ref: ../dsi-controller.yaml#
> > +
> > +required:
> > +  - compatible
> > +  - reg
> > +  - interrupts
> > +  - clocks
> > +  - clock-names
> > +  - phys
> > +  - phy-names
> > +  - ports
> > +
> > +unevaluatedProperties: false
> > +
> 
> Best regards,
> Krzysztof



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux