Hi Andre,
On 7/1/22 6:24 AM, Andre Przywara wrote:
> This (relatively) new SoC is similar to the H6, but drops the (broken)
> PCIe support and the USB 3.0 controller. It also gets the management
> controller removed, which in turn removes *some*, but not all of the
> devices formerly dedicated to the ARISC (CPUS).
> And while there is still the extra sunxi interrupt controller, the
> package lacks the corresponding NMI pin, so no interrupts for the PMIC.
>
> The reserved memory node is actually handled by Trusted Firmware now,
> but U-Boot fails to propagate this to a separately loaded DTB, so we
> keep it in here for now, until U-Boot learns to do this properly.
Other than the decision about the reserved-memory node, which is being discussed
in the v11 thread, this looks good to me. Just a few minor comments below.
Regards,
Samuel
> Signed-off-by: Andre Przywara <andre.przywara@xxxxxxx>
> ---
> .../arm64/boot/dts/allwinner/sun50i-h616.dtsi | 579 ++++++++++++++++++
> 1 file changed, 579 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> new file mode 100644
> index 0000000000000..478f0b395ff58
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616.dtsi
> @@ -0,0 +1,579 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +// Copyright (C) 2020 Arm Ltd.
> +// based on the H6 dtsi, which is:
> +// Copyright (C) 2017 Icenowy Zheng <icenowy@xxxxxxx>
> +
> +#include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/clock/sun50i-h616-ccu.h>
> +#include <dt-bindings/clock/sun50i-h6-r-ccu.h>
> +#include <dt-bindings/reset/sun50i-h616-ccu.h>
> +#include <dt-bindings/reset/sun50i-h6-r-ccu.h>
> +
> +/ {
> + interrupt-parent = <&gic>;
> + #address-cells = <2>;
> + #size-cells = <2>;
> +
> + cpus {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + cpu0: cpu@0 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + reg = <0>;
> + enable-method = "psci";
> + clocks = <&ccu CLK_CPUX>;
> + };
> +
> + cpu1: cpu@1 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + reg = <1>;
> + enable-method = "psci";
> + clocks = <&ccu CLK_CPUX>;
> + };
> +
> + cpu2: cpu@2 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + reg = <2>;
> + enable-method = "psci";
> + clocks = <&ccu CLK_CPUX>;
> + };
> +
> + cpu3: cpu@3 {
> + compatible = "arm,cortex-a53";
> + device_type = "cpu";
> + reg = <3>;
> + enable-method = "psci";
> + clocks = <&ccu CLK_CPUX>;
> + };
> + };
> +
> + reserved-memory {
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + /* 512KiB reserved for ARM Trusted Firmware (BL31) */
> + secmon_reserved: secmon@40000000 {
> + reg = <0x0 0x40000000 0x0 0x80000>;
> + no-map;
> + };
> + };
> +
> + osc24M: osc24M-clk {
> + #clock-cells = <0>;
> + compatible = "fixed-clock";
> + clock-frequency = <24000000>;
> + clock-output-names = "osc24M";
> + };
> +
> + pmu {
> + compatible = "arm,cortex-a53-pmu";
> + interrupts = <GIC_SPI 140 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 141 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 142 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 143 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>;
> + };
> +
> + psci {
> + compatible = "arm,psci-0.2";
> + method = "smc";
> + };
> +
> + timer {
> + compatible = "arm,armv8-timer";
> + arm,no-tick-in-suspend;
> + interrupts = <GIC_PPI 13
> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> + <GIC_PPI 14
> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> + <GIC_PPI 11
> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>,
> + <GIC_PPI 10
> + (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> + };
> +
> + soc@0 {
No unit address needed here.
> + compatible = "simple-bus";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0x0 0x0 0x0 0x40000000>;
> +
> + syscon: syscon@3000000 {
> + compatible = "allwinner,sun50i-h616-system-control";
> + reg = <0x03000000 0x1000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + sram_c: sram@28000 {
> + compatible = "mmio-sram";
> + reg = <0x00028000 0x30000>;
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges = <0 0x00028000 0x30000>;
> + };
> + };
> +
> + ccu: clock@3001000 {
> + compatible = "allwinner,sun50i-h616-ccu";
> + reg = <0x03001000 0x1000>;
> + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>;
Please use the recently-added symbolic constants for the RTC clocks.
> + clock-names = "hosc", "losc", "iosc";
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + };
> +
> + watchdog: watchdog@30090a0 {
> + compatible = "allwinner,sun50i-h616-wdt",
> + "allwinner,sun6i-a31-wdt";
> + reg = <0x030090a0 0x20>;
> + interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&osc24M>;
> + };
> +
> + pio: pinctrl@300b000 {
> + compatible = "allwinner,sun50i-h616-pinctrl";
> + reg = <0x0300b000 0x400>;
> + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_APB1>, <&osc24M>, <&rtc 0>;
Same for the RTC clock here.
> + clock-names = "apb", "hosc", "losc";
> + gpio-controller;
> + #gpio-cells = <3>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> +
> + ext_rgmii_pins: rgmii-pins {
> + pins = "PI0", "PI1", "PI2", "PI3", "PI4",
> + "PI5", "PI7", "PI8", "PI9", "PI10",
> + "PI11", "PI12", "PI13", "PI14", "PI15",
> + "PI16";
> + function = "emac0";
> + drive-strength = <40>;
> + };
> +
> + i2c0_pins: i2c0-pins {
> + pins = "PI6", "PI7";
> + function = "i2c0";
> + };
> +
> + i2c3_ph_pins: i2c3-ph-pins {
> + pins = "PH4", "PH5";
> + function = "i2c3";
> + };
> +
> + ir_rx_pin: ir-rx-pin {
> + pins = "PH10";
> + function = "ir_rx";
> + };
> +
> + mmc0_pins: mmc0-pins {
> + pins = "PF0", "PF1", "PF2", "PF3",
> + "PF4", "PF5";
> + function = "mmc0";
> + drive-strength = <30>;
> + bias-pull-up;
> + };
> +
> + /omit-if-no-ref/
> + mmc1_pins: mmc1-pins {
> + pins = "PG0", "PG1", "PG2", "PG3",
> + "PG4", "PG5";
> + function = "mmc1";
> + drive-strength = <30>;
> + bias-pull-up;
> + };
> +
> + mmc2_pins: mmc2-pins {
> + pins = "PC0", "PC1", "PC5", "PC6",
> + "PC8", "PC9", "PC10", "PC11",
> + "PC13", "PC14", "PC15", "PC16";
> + function = "mmc2";
> + drive-strength = <30>;
> + bias-pull-up;
> + };
> +
> + /omit-if-no-ref/
> + spi0_pins: spi0-pins {
> + pins = "PC0", "PC2", "PC4";
> + function = "spi0";
> + };
> +
> + /omit-if-no-ref/
> + spi0_cs0_pin: spi0-cs0-pin {
> + pins = "PC3";
> + function = "spi0";
> + };
> +
> + /omit-if-no-ref/
> + spi1_pins: spi1-pins {
> + pins = "PH6", "PH7", "PH8";
> + function = "spi1";
> + };
> +
> + /omit-if-no-ref/
> + spi1_cs0_pin: spi1-cs0-pin {
> + pins = "PH5";
> + function = "spi1";
> + };
> +
> + uart0_ph_pins: uart0-ph-pins {
> + pins = "PH0", "PH1";
> + function = "uart0";
> + };
> +
> + /omit-if-no-ref/
> + uart1_pins: uart1-pins {
> + pins = "PG6", "PG7";
> + function = "uart1";
> + };
> +
> + /omit-if-no-ref/
> + uart1_rts_cts_pins: uart1-rts-cts-pins {
> + pins = "PG8", "PG9";
> + function = "uart1";
> + };
> + };
> +
> + gic: interrupt-controller@3021000 {
> + compatible = "arm,gic-400";
> + reg = <0x03021000 0x1000>,
> + <0x03022000 0x2000>,
> + <0x03024000 0x2000>,
> + <0x03026000 0x2000>;
> + interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> + interrupt-controller;
> + #interrupt-cells = <3>;
> + };
> +
> + mmc0: mmc@4020000 {
> + compatible = "allwinner,sun50i-h616-mmc",
> + "allwinner,sun50i-a100-mmc";
> + reg = <0x04020000 0x1000>;
> + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
> + clock-names = "ahb", "mmc";
> + resets = <&ccu RST_BUS_MMC0>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins>;
> + status = "disabled";
> + max-frequency = <150000000>;
> + cap-sd-highspeed;
> + cap-mmc-highspeed;
> + mmc-ddr-3_3v;
> + cap-sdio-irq;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + mmc1: mmc@4021000 {
> + compatible = "allwinner,sun50i-h616-mmc",
> + "allwinner,sun50i-a100-mmc";
> + reg = <0x04021000 0x1000>;
> + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
> + clock-names = "ahb", "mmc";
> + resets = <&ccu RST_BUS_MMC1>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc1_pins>;
> + status = "disabled";
> + max-frequency = <150000000>;
> + cap-sd-highspeed;
> + cap-mmc-highspeed;
> + mmc-ddr-3_3v;
> + cap-sdio-irq;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + mmc2: mmc@4022000 {
> + compatible = "allwinner,sun50i-h616-emmc",
> + "allwinner,sun50i-a100-emmc";
> + reg = <0x04022000 0x1000>;
> + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
> + clock-names = "ahb", "mmc";
> + resets = <&ccu RST_BUS_MMC2>;
> + reset-names = "ahb";
> + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc2_pins>;
> + status = "disabled";
> + max-frequency = <150000000>;
> + cap-sd-highspeed;
> + cap-mmc-highspeed;
> + mmc-ddr-3_3v;
> + cap-sdio-irq;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + uart0: serial@5000000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x05000000 0x400>;
> + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART0>;
> + resets = <&ccu RST_BUS_UART0>;
> + status = "disabled";
> + };
> +
> + uart1: serial@5000400 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x05000400 0x400>;
> + interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART1>;
> + resets = <&ccu RST_BUS_UART1>;
> + status = "disabled";
> + };
> +
> + uart2: serial@5000800 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x05000800 0x400>;
> + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART2>;
> + resets = <&ccu RST_BUS_UART2>;
> + status = "disabled";
> + };
> +
> + uart3: serial@5000c00 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x05000c00 0x400>;
> + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART3>;
> + resets = <&ccu RST_BUS_UART3>;
> + status = "disabled";
> + };
> +
> + uart4: serial@5001000 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x05001000 0x400>;
> + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART4>;
> + resets = <&ccu RST_BUS_UART4>;
> + status = "disabled";
> + };
> +
> + uart5: serial@5001400 {
> + compatible = "snps,dw-apb-uart";
> + reg = <0x05001400 0x400>;
> + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
> + reg-shift = <2>;
> + reg-io-width = <4>;
> + clocks = <&ccu CLK_BUS_UART5>;
> + resets = <&ccu RST_BUS_UART5>;
> + status = "disabled";
> + };
> +
> + i2c0: i2c@5002000 {
> + compatible = "allwinner,sun50i-h616-i2c",
> + "allwinner,sun6i-a31-i2c";
Future note: this will be affected by [1] which adds a fallback compatible for
variants with offload support. That way we don't have to support them all
individually in the driver if/when we implement that.
[1]: https://lore.kernel.org/lkml/20220702052544.31443-1-samuel@xxxxxxxxxxxx/
> + reg = <0x05002000 0x400>;
> + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C0>;
> + resets = <&ccu RST_BUS_I2C0>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&i2c0_pins>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + i2c1: i2c@5002400 {
> + compatible = "allwinner,sun50i-h616-i2c",
> + "allwinner,sun6i-a31-i2c";
> + reg = <0x05002400 0x400>;
> + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C1>;
> + resets = <&ccu RST_BUS_I2C1>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + i2c2: i2c@5002800 {
> + compatible = "allwinner,sun50i-h616-i2c",
> + "allwinner,sun6i-a31-i2c";
> + reg = <0x05002800 0x400>;
> + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C2>;
> + resets = <&ccu RST_BUS_I2C2>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + i2c3: i2c@5002c00 {
> + compatible = "allwinner,sun50i-h616-i2c",
> + "allwinner,sun6i-a31-i2c";
> + reg = <0x05002c00 0x400>;
> + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C3>;
> + resets = <&ccu RST_BUS_I2C3>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + i2c4: i2c@5003000 {
> + compatible = "allwinner,sun50i-h616-i2c",
> + "allwinner,sun6i-a31-i2c";
> + reg = <0x05003000 0x400>;
> + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_I2C4>;
> + resets = <&ccu RST_BUS_I2C4>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + spi0: spi@5010000 {
> + compatible = "allwinner,sun50i-h616-spi",
> + "allwinner,sun8i-h3-spi";
> + reg = <0x05010000 0x1000>;
> + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
> + clock-names = "ahb", "mod";
> + resets = <&ccu RST_BUS_SPI0>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + spi1: spi@5011000 {
> + compatible = "allwinner,sun50i-h616-spi",
> + "allwinner,sun8i-h3-spi";
> + reg = <0x05011000 0x1000>;
> + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
> + clock-names = "ahb", "mod";
> + resets = <&ccu RST_BUS_SPI1>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + emac0: ethernet@5020000 {
> + compatible = "allwinner,sun50i-h616-emac",
> + "allwinner,sun50i-a64-emac";
> + syscon = <&syscon>;
> + reg = <0x05020000 0x10000>;
> + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "macirq";
> + resets = <&ccu RST_BUS_EMAC0>;
> + reset-names = "stmmaceth";
> + clocks = <&ccu CLK_BUS_EMAC0>;
> + clock-names = "stmmaceth";
Nit: clocks then resets then syscon, to follow the usual order.
> + status = "disabled";
> +
> + mdio0: mdio {
> + compatible = "snps,dwmac-mdio";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> + };
> +
> + rtc: rtc@7000000 {
> + compatible = "allwinner,sun50i-h616-rtc";
> + reg = <0x07000000 0x400>;
> + interrupts = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&r_ccu CLK_R_APB1_RTC>, <&osc24M>,
> + <&ccu CLK_PLL_SYSTEM_32K>;
> + clock-names = "bus", "hosc",
> + "pll-32k";
> + clock-output-names = "osc32k", "osc32k-out", "iosc";
Since the RTC clock indices were formalized in the binding, this is no longer
needed.
> + #clock-cells = <1>;
> + };
> +
> + r_ccu: clock@7010000 {
> + compatible = "allwinner,sun50i-h616-r-ccu";
> + reg = <0x07010000 0x210>;
> + clocks = <&osc24M>, <&rtc 0>, <&rtc 2>,
Symbolic constants here and in r_pio as well, please.
> + <&ccu CLK_PLL_PERIPH0>;
> + clock-names = "hosc", "losc", "iosc", "pll-periph";
> + #clock-cells = <1>;
> + #reset-cells = <1>;
> + };
> +
> + r_pio: pinctrl@7022000 {
> + compatible = "allwinner,sun50i-h616-r-pinctrl";
> + reg = <0x07022000 0x400>;
> + clocks = <&r_ccu CLK_R_APB1>, <&osc24M>, <&rtc 0>;
> + clock-names = "apb", "hosc", "losc";
> + gpio-controller;
> + #gpio-cells = <3>;
> +
> + r_i2c_pins: r-i2c-pins {
This is unlikely be used (as opposed to RSB), so I suggest omit-if-no-ref.
> + pins = "PL0", "PL1";
> + function = "s_i2c";
> + };
> +
> + r_rsb_pins: r-rsb-pins {
> + pins = "PL0", "PL1";
> + function = "s_rsb";
> + };
> + };
> +
> + ir: ir@7040000 {
> + compatible = "allwinner,sun50i-h616-ir",
> + "allwinner,sun6i-a31-ir";
> + reg = <0x07040000 0x400>;
> + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&r_ccu CLK_R_APB1_IR>,
> + <&r_ccu CLK_IR>;
> + clock-names = "apb", "ir";
> + resets = <&r_ccu RST_R_APB1_IR>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&ir_rx_pin>;
> + status = "disabled";
> + };
> +
> + r_i2c: i2c@7081400 {
> + compatible = "allwinner,sun50i-h616-i2c",
> + "allwinner,sun6i-a31-i2c";
> + reg = <0x07081400 0x400>;
> + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&r_ccu CLK_R_APB2_I2C>;
> + resets = <&r_ccu RST_R_APB2_I2C>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> +
> + r_rsb: rsb@7083000 {
> + compatible = "allwinner,sun50i-h616-rsb",
> + "allwinner,sun8i-a23-rsb";
> + reg = <0x07083000 0x400>;
> + interrupts = <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&r_ccu CLK_R_APB2_RSB>;
> + clock-frequency = <3000000>;
> + resets = <&r_ccu RST_R_APB2_RSB>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&r_rsb_pins>;
> + status = "disabled";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> + };
> +};
>
