Re: [PATCH v5 05/11] drm: add Atmel HLCDC Display Controller support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On Mon, Sep 8, 2014 at 4:43 AM, Boris BREZILLON
<boris.brezillon@xxxxxxxxxxxxxxxxxx> wrote:
> The Atmel HLCDC (HLCD Controller) IP available on some Atmel SoCs (i.e.
> at91sam9n12, at91sam9x5 family or sama5d3 family) provides a display
> controller device.
>
> This display controller supports at least one primary plane and might
> provide several overlays and an hardware cursor depending on the IP
> version.
>
> At the moment, this driver only implements an RGB connector to interface
> with LCD panels, but support for other kind of external devices might be
> added later.
>
> Signed-off-by: Boris BREZILLON <boris.brezillon@xxxxxxxxxxxxxxxxxx>
> Tested-by: Ludovic Desroches <ludovic.desroches@xxxxxxxxx>

A few small comments below, but with those addressed it has my

Reviewed-by: Rob Clark <robdclark@xxxxxxxxx>


> ---
>  drivers/gpu/drm/Kconfig                          |   2 +
>  drivers/gpu/drm/Makefile                         |   1 +
>  drivers/gpu/drm/atmel-hlcdc/Kconfig              |  13 +
>  drivers/gpu/drm/atmel-hlcdc/Makefile             |   7 +
>  drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c   | 286 ++++++++
>  drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_dc.c     | 488 +++++++++++++
>  drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_dc.h     | 224 ++++++
>  drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_layer.c  | 656 ++++++++++++++++++
>  drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_layer.h  | 403 +++++++++++
>  drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_output.c | 476 +++++++++++++
>  drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_plane.c  | 836 +++++++++++++++++++++++
>  11 files changed, 3392 insertions(+)
>  create mode 100644 drivers/gpu/drm/atmel-hlcdc/Kconfig
>  create mode 100644 drivers/gpu/drm/atmel-hlcdc/Makefile
>  create mode 100644 drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_crtc.c
>  create mode 100644 drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_dc.c
>  create mode 100644 drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_dc.h
>  create mode 100644 drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_layer.c
>  create mode 100644 drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_layer.h
>  create mode 100644 drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_output.c
>  create mode 100644 drivers/gpu/drm/atmel-hlcdc/atmel_hlcdc_plane.c
>

[snip]

> +
> +/**
> + * Atmel HLCDC plane rotation enum
> + *
> + * TODO: export DRM_ROTATE_XX macros defined by omap driver and use them
> + * instead of defining this enum.
> + */
> +enum atmel_hlcdc_plane_rotation {
> +       ATMEL_HLCDC_PLANE_NO_ROTATION,
> +       ATMEL_HLCDC_PLANE_90DEG_ROTATION,
> +       ATMEL_HLCDC_PLANE_180DEG_ROTATION,
> +       ATMEL_HLCDC_PLANE_270DEG_ROTATION,
> +};

DRM_ROTATE_* are already in drm_crtc.h

[snip]

> +static int atmel_hlcdc_rgb_mode_valid(struct drm_connector *connector,
> +                                     struct drm_display_mode *mode)
> +{
> +       return MODE_OK;
> +}

your _mode_valid() should perhaps somehow check the constraints in
atmel_hlcdc_crtc_mode_set()?  This way invalid modes get filtered out
earlier..

[snip]

> +static struct atmel_hlcdc_plane_properties *
> +atmel_hlcdc_plane_create_properties(struct drm_device *dev)
> +{
> +       struct atmel_hlcdc_plane_properties *props;
> +       const struct drm_prop_enum_list rotations[] = {
> +               { ATMEL_HLCDC_PLANE_NO_ROTATION,   "rotate-0" },
> +               { ATMEL_HLCDC_PLANE_90DEG_ROTATION,  "rotate-90" },
> +               { ATMEL_HLCDC_PLANE_180DEG_ROTATION, "rotate-180" },
> +               { ATMEL_HLCDC_PLANE_270DEG_ROTATION, "rotate-270" },
> +       };
> +

you could just use drm_mode_create_rotation_property() now


> +       props = devm_kzalloc(dev->dev, sizeof(*props), GFP_KERNEL);
> +       if (!props)
> +               return ERR_PTR(-ENOMEM);
> +
> +       props->alpha = drm_property_create_range(dev, 0, "alpha", 0, 255);
> +       if (!props->alpha)
> +               return ERR_PTR(-ENOMEM);
> +
> +       props->rotation = drm_property_create_enum(dev, 0, "rotation",
> +                                               rotations,
> +                                               ARRAY_SIZE(rotations));
> +       return props;
> +}
> +
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux