Le 22/05/2022 à 09:04, LI Qingwu a écrit :
Add support for Murata SCL3300, a 3-axis MEMS accelerometer.
Same as SCA3300, it has the accelerometer and temperature output.
Datasheet: www.murata.com/en-us/products/sensor/inclinometer/overview/lineup/scl3300
Signed-off-by: LI Qingwu <Qing-wu.Li-t1cy0uBObHa2smIkw38IFAiE/XJ0vlP8@xxxxxxxxxxxxxxxx>
---
drivers/iio/accel/sca3300.c | 28 ++++++++++++++++++++++++++--
1 file changed, 26 insertions(+), 2 deletions(-)
diff --git a/drivers/iio/accel/sca3300.c b/drivers/iio/accel/sca3300.c
index e57aba79c32b..10bedb14d4f0 100644
--- a/drivers/iio/accel/sca3300.c
+++ b/drivers/iio/accel/sca3300.c
@@ -38,6 +38,7 @@
/* Device ID */
#define SCA3300_REG_WHOAMI 0x10
#define SCA3300_WHOAMI_ID 0x51
+#define SCL3300_WHOAMI_ID 0xC1
/* Device return status and mask */
#define SCA3300_VALUE_RS_ERROR 0x3
@@ -96,10 +97,18 @@ static const struct iio_chan_spec sca3300_channels[] = {
static const int sca3300_lp_freq[] = {70, 10};
static const int sca3300_lp_freq_map[] = {0, 0, 0, 1};
+static const int scl3300_lp_freq[] = {40, 70, 10};
+static const int scl3300_lp_freq_map[] = {0, 1, 2};
+
static const int sca3300_accel_scale[][2] = {{0, 370}, {0, 741}, {0, 185}};
static const int sca3300_accel_scale_map[] = {0, 1, 2, 2};
+static const int scl3300_accel_scale[][2] = {{0, 167}, {0, 333}, {0, 83}};
+static const int scl3300_accel_scale_map[] = {0, 1, 2};
+
static const int sca3300_avail_modes_map[] = {0, 1, 2, 3};
+static const int scl3300_avail_modes_map[] = {0, 1, 3};
+
static const unsigned long sca3300_scan_masks[] = {
BIT(SCA3300_ACC_X) | BIT(SCA3300_ACC_Y) | BIT(SCA3300_ACC_Z) |
BIT(SCA3300_TEMP),
@@ -159,6 +168,20 @@ static const struct sca3300_chip_info sca3300_chip_tbl[] = {
.num_avail_modes = 4,
.chip_id = SCA3300_WHOAMI_ID,
},
+ { .scan_masks = sca3300_scan_masks,
+ .channels = sca3300_channels,
+ .num_channels = ARRAY_SIZE(sca3300_channels),
+ .num_accel_scales = ARRAY_SIZE(scl3300_accel_scale)*2,
+ .accel_scale = scl3300_accel_scale,
+ .accel_scale_map = scl3300_accel_scale_map,
+ .num_freqs = ARRAY_SIZE(scl3300_lp_freq),
+ .freq_table = scl3300_lp_freq,
+ .freq_map = scl3300_lp_freq_map,
+ .name = "scl3300",
+ .avail_modes_table = scl3300_avail_modes_map,
+ .num_avail_modes = 3,
+ .chip_id = SCL3300_WHOAMI_ID,
+ },
};
DECLARE_CRC8_TABLE(sca3300_crc_table);
@@ -444,9 +467,9 @@ static int sca3300_init(struct sca3300_data *sca_data,
/*
* Wait 1ms after SW-reset command.
- * Wait 15ms for settling of signal paths.
+ * Wait 25ms for settling of signal paths.
Hi,
maybe the comment (IIUC) should say that the timing depends of sca3300
(15 ms) or scl3300 (25 ms) and that the max of the 2 values is taken.
Or have this delay depends of the chip in the code below.
CJ
*/
- usleep_range(16e3, 50e3);
+ usleep_range(26e3, 50e3);
ret = sca3300_read_reg(sca_data, SCA3300_REG_WHOAMI, &value);
if (ret)
@@ -573,6 +596,7 @@ static int sca3300_probe(struct spi_device *spi)
static const struct of_device_id sca3300_dt_ids[] = {
{ .compatible = "murata,sca3300"},
+ { .compatible = "murata,scl3300"},
{}
};
MODULE_DEVICE_TABLE(of, sca3300_dt_ids);
