This work is largely based on the previous work by Bjorn Andersson ([1]) Changes since v5: - Drop icc patch, as there are questions whether the original paths are valid. It will be submitted separately. Changes since v4: - Remove unused mdp and sd-card-det-n DT nodes from the ifc6560 dts (thanks to Konrad). Changes since v3 (most points based on review by Marijn): - Fixed a typo in dsi0 patch - Fixed indentation here and there - Renamed qusb2phy to qusb2phy0 to play better with qusb2phy1 - Fixed the ICC path for the GPU - Fixed sdhc2 pinconf for sdm636-sony-xperia-ganges-mermaid - Moved SDHC2 card detect gpio pin to board files Changes since v2: - Removed useless enablement of mdp node from the board file. It is already enabled in the SoC dtsi file. Changes since v1 (mostly based on Kondrad's review): - Also disabled dsi0/dsi0 phy in sdm630.dtsi - Removed the clock from BAM DMA devices rather than disabling them completely - Replaced numbers with symbolic names for interconnects in sdm630.dtsi - Switched to "qcom,sda660" as a fallback compatible string - Added dt-bindings for the qcom,sda660 compat - Removed extra nesting level from the adsp firmware path - Replaced numbers with proper symbolic names in the board file - Added chassis-type property - Changed the order of blsp entries in the board file - Removed spurious newlines - Changed the order of regulator properties - Changed the DSI data-lines to list all four lanes. Still use just three lanes for the adv bridge (and describe the reason in the comment) Changes since Bjorn's v2: - Disable dsi1, dsi1 phy, GPU by default in sdm660.dtsi/sdm630.dtsi - Fix qusb2phy ref clock - Added USB2 host support to sdm630.dtsi - Renamed DTS to follow SoC-vendor-board pattern - Fixed vph_pwr voltage - Removed extra/unrelated comments - Added keys, USB2, USB3, - Added configuration for the attached HDMI bridge - Enabled MDP, MDSS and DSI0/DSI0 PHY devices - Removed uart pinctrl and /reserved-mem nodes (present in main dtsi file) - Added card detection for the SDCC2 - Disabled BLSP BAM DMA devices, they make the board reset during boot [1] https://lore.kernel.org/linux-arm-msm/20210825221110.1498718-1-bjorn.andersson@xxxxxxxxxx/#t Dmitry Baryshkov (11): arm64: dts: qcom: sdm630: disable dsi0/dsi0_phy by default arm64: dts: qcom: sdm660: disable dsi1/dsi1_phy by default arm64: dts: qcom: sdm630: disable GPU by default arm64: dts: qcom: sdm630: fix the qusb2phy ref clock arm64: dts: qcom: sdm630: rename qusb2phy to qusb2phy0 arm64: dts: qcom: sdm630: add second (HS) USB host support arm64: dts: qcom: sdm630: fix gpu's interconnect path arm64: dts: qcom: sdm636-sony-xperia-ganges-mermaid: correct sdc2 pinconf arm64: dts: qcom: sdm660: move SDHC2 card detect pinconf to board files arm64: dts: qcom: sdm660: Add initial Inforce IFC6560 board support dt-bindings: arm: qcom: document sda660 SoC and ifc6560 board .../devicetree/bindings/arm/qcom.yaml | 6 + arch/arm64/boot/dts/qcom/Makefile | 1 + .../boot/dts/qcom/sda660-inforce-ifc6560.dts | 461 ++++++++++++++++++ .../dts/qcom/sdm630-sony-xperia-nile.dtsi | 18 +- arch/arm64/boot/dts/qcom/sdm630.dtsi | 81 ++- .../sdm636-sony-xperia-ganges-mermaid.dts | 2 +- .../boot/dts/qcom/sdm660-xiaomi-lavender.dts | 18 +- arch/arm64/boot/dts/qcom/sdm660.dtsi | 3 + 8 files changed, 571 insertions(+), 19 deletions(-) create mode 100644 arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts -- 2.35.1
