Add binding for the Qualcomm Resource Power Manager (RPM) found in 8660,
8960 and 8064 based devices. The binding currently describes the rpm
itself and the regulator subnodes.
Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxxxxxx>
---
Documentation/devicetree/bindings/mfd/qcom-rpm.txt | 246 ++++++++++++++++++++
include/dt-bindings/mfd/qcom-rpm.h | 154 ++++++++++++
2 files changed, 400 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/qcom-rpm.txt
create mode 100644 include/dt-bindings/mfd/qcom-rpm.h
diff --git a/Documentation/devicetree/bindings/mfd/qcom-rpm.txt b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
new file mode 100644
index 0000000..4264021
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/qcom-rpm.txt
@@ -0,0 +1,246 @@
+Qualcomm Resource Power Manager (RPM)
+
+This driver is used to interface with the Resource Power Manager (RPM) found in
+various Qualcomm platforms. The RPM allows each component in the system to vote
+for state of the system resources, such as clocks, regulators and bus
+frequencies.
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,rpm-apq8064"
+ "qcom,rpm-msm8660"
+ "qcom,rpm-msm8960"
+
+- reg:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: base address and size of the RPM's message ram
+
+- interrupts:
+ Usage: required
+ Value type: <prop-encoded-array>
+ Definition: three entries specifying the RPM's:
+ 1. acknowledgement interrupt
+ 2. error interrupt
+ 3. wakeup interrupt
+
+- interrupt-names:
+ Usage: required
+ Value type: <string-array>
+ Definition: must be the three strings "ack", "err" and "wakeup", in order
+
+- #address-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 1
+
+- #size-cells:
+ Usage: required
+ Value type: <u32>
+ Definition: must be 0
+
+- qcom,ipc:
+ Usage: required
+ Value type: <prop-encoded-array>
+
+ Definition: three entries specifying the outgoing ipc bit used for
+ signaling the RPM:
+ - phandle to a syscon node representing the apcs registers
+ - u32 representing offset to the register within the syscon
+ - u32 representing the ipc bit within the register
+
+
+= SUBDEVICES
+
+The RPM exposes resources to its subnodes. The below bindings specify the set
+of valid subnodes that can operate on these resources.
+
+== Switch-mode Power Supply regulator
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,rpm-pm8058-smps"
+ "qcom,rpm-pm8901-ftsmps"
+ "qcom,rpm-pm8921-smps"
+ "qcom,rpm-pm8921-ftsmps"
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: resource as defined in <dt-bindings/mfd/qcom-rpm.h>
+ must be one of:
+ QCOM_RPM_PM8058_SMPS0 - QCOM_RPM_PM8058_SMPS4,
+ QCOM_RPM_PM8821_SMPS1 - QCOM_RPM_PM8821_SMPS2,
+ QCOM_RPM_PM8901_SMPS0 - QCOM_RPM_PM8901_SMPS4,
+ QCOM_RPM_PM8921_SMPS1 - QCOM_RPM_PM8921_SMPS8
+
+- bias-pull-down:
+ Usage: optional
+ Value type: <empty>
+ Definition: enable pull down of the regulator when inactive
+
+- qcom,switch-mode-frequency:
+ Usage: required
+ Value type: <u32>
+ Definition: Frequency (Hz) of the switch-mode power supply;
+ must be one of:
+ 19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
+ 2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
+ 1480000, 1370000, 1280000, 1200000
+
+- qcom,force-mode:
+ Usage: optional (default if no other qcom,force-mode is specified)
+ Value type: <u32>
+ Defintion: indicates that the regulator should be forced to a
+ particular mode, valid values are:
+ QCOM_RPM_FORCE_MODE_NONE - do not force any mode
+ QCOM_RPM_FORCE_MODE_LPM - force into low power mode
+ QCOM_RPM_FORCE_MODE_HPM - force into high power mode
+ QCOM_RPM_FORCE_MODE_AUTO - allow regulator to automatically
+ select its own mode based on
+ realtime current draw, only for:
+ qcom,rpm-pm8921-smps,
+ qcom,rpm-pm8921-ftsmps
+
+- qcom,power-mode-hysteretic:
+ Usage: optional
+ Value type: <empty>
+ Definition: select that the power supply should operate in hysteretic
+ mode, instead of the default pwm mode
+
+Standard regulator bindings are used inside switch mode power supply subnodes.
+Check Documentation/devicetree/bindings/regulator/regulator.txt for more
+details.
+
+== Low-dropout regulator
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,rpm-pm8058-pldo"
+ "qcom,rpm-pm8058-nldo"
+ "qcom,rpm-pm8901-pldo"
+ "qcom,rpm-pm8901-nldo"
+ "qcom,rpm-pm8921-pldo"
+ "qcom,rpm-pm8921-nldo"
+ "qcom,rpm-pm8921-nldo1200"
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: resource as defined in <dt-bindings/mfd/qcom-rpm.h>
+ must be one of:
+ QCOM_RPM_PM8058_LDO0 - QCOM_RPM_PM8058_LDO25,
+ QCOM_RPM_PM8821_LDO1,
+ QCOM_RPM_PM8901_LDO0 - QCOM_RPM_PM8901_LDO6,
+ QCOM_RPM_PM8921_LDO1 - QCOM_RPM_PM8921_LDO29
+
+- bias-pull-down:
+ Usage: optional
+ Value type: <empty>
+ Definition: enable pull down of the regulator when inactive
+
+- qcom,force-mode:
+ Usage: optional
+ Value type: <u32>
+ Defintion: indicates that the regulator should not be forced to any
+ particular mode, valid values are:
+ QCOM_RPM_FORCE_MODE_NONE - do not force any mode
+ QCOM_RPM_FORCE_MODE_LPM - force into low power mode
+ QCOM_RPM_FORCE_MODE_HPM - force into high power mode
+ QCOM_RPM_FORCE_MODE_BYPASS - set regulator to use bypass
+ mode, i.e. to act as a switch
+ and not regulate, only for:
+ qcom,rpm-pm8921-pldo,
+ qcom,rpm-pm8921-nldo,
+ qcom,rpm-pm8921-nldo1200
+
+Standard regulator bindings are used inside switch low-dropout regulator
+subnodes. Check Documentation/devicetree/bindings/regulator/regulator.txt for
+more details.
+
+== Negative Charge Pump
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,rpm-pm8058-ncp"
+ "qcom,rpm-pm8921-ncp"
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: resource as defined in <dt-bindings/mfd/qcom-rpm.h>
+ must be one of:
+ QCOM_RPM_PM8058_NCP,
+ QCOM_RPM_PM8921_NCP
+
+- qcom,switch-mode-frequency:
+ Usage: required
+ Value type: <u32>
+ Definition: Frequency (Hz) of the swith mode power supply;
+ must be one of:
+ 19200000, 9600000, 6400000, 4800000, 3840000, 3200000,
+ 2740000, 2400000, 2130000, 1920000, 1750000, 1600000,
+ 1480000, 1370000, 1280000, 1200000
+
+Standard regulator bindings are used inside negative charge pump regulator
+subnodes. Check Documentation/devicetree/bindings/regulator/regulator.txt for
+more details.
+
+== Switch
+
+- compatible:
+ Usage: required
+ Value type: <string>
+ Definition: must be one of:
+ "qcom,rpm-pm8058-switch"
+ "qcom,rpm-pm8901-switch"
+ "qcom,rpm-pm8921-switch"
+
+- reg:
+ Usage: required
+ Value type: <u32>
+ Definition: resource as defined in <dt-bindings/mfd/qcom/qcom-rpm.h>
+ must be one of:
+ QCOM_RPM_PM8058_LVS0 - QCOM_RPM_PM8058_LVS1,
+ QCOM_RPM_PM8901_LVS0 - QCOM_RPM_PM8901_LVS3,
+ QCOM_RPM_PM8901_MVS,
+ QCOM_RPM_PM8921_LVS1 - QCOM_RPM_PM8921_LVS7,
+ QCOM_RPM_PM8921_MVS
+
+= EXAMPLE
+
+ #include <dt-bindings/mfd/qcom-rpm.h>
+
+ rpm@108000 {
+ compatible = "qcom,rpm-msm8960";
+ reg = <0x108000 0x1000>;
+ qcom,ipc = <&apcs 0x8 2>;
+
+ interrupts = <0 19 0>, <0 21 0>, <0 22 0>;
+ interrupt-names = "ack", "err", "wakeup";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ pm8921_smps1: pm8921-smps1 {
+ compatible = "qcom,rpm-pm8921-smps";
+ reg = <QCOM_RPM_PM8921_SMPS1>;
+
+ regulator-min-microvolt = <1225000>;
+ regulator-max-microvolt = <1225000>;
+ regulator-always-on;
+
+ bias-pull-down;
+
+ qcom,switch-mode-frequency = <3200000>;
+ };
+ };
+
diff --git a/include/dt-bindings/mfd/qcom-rpm.h b/include/dt-bindings/mfd/qcom-rpm.h
new file mode 100644
index 0000000..388a6f3
--- /dev/null
+++ b/include/dt-bindings/mfd/qcom-rpm.h
@@ -0,0 +1,154 @@
+/*
+ * This header provides constants for the Qualcomm RPM bindings.
+ */
+
+#ifndef _DT_BINDINGS_MFD_QCOM_RPM_H
+#define _DT_BINDINGS_MFD_QCOM_RPM_H
+
+/*
+ * Constants use to identify individual resources in the RPM.
+ */
+#define QCOM_RPM_APPS_FABRIC_ARB 1
+#define QCOM_RPM_APPS_FABRIC_CLK 2
+#define QCOM_RPM_APPS_FABRIC_HALT 3
+#define QCOM_RPM_APPS_FABRIC_IOCTL 4
+#define QCOM_RPM_APPS_FABRIC_MODE 5
+#define QCOM_RPM_APPS_L2_CACHE_CTL 6
+#define QCOM_RPM_CFPB_CLK 7
+#define QCOM_RPM_CXO_BUFFERS 8
+#define QCOM_RPM_CXO_CLK 9
+#define QCOM_RPM_DAYTONA_FABRIC_CLK 10
+#define QCOM_RPM_DDR_DMM 11
+#define QCOM_RPM_EBI1_CLK 12
+#define QCOM_RPM_HDMI_SWITCH 13
+#define QCOM_RPM_MMFPB_CLK 14
+#define QCOM_RPM_MM_FABRIC_ARB 15
+#define QCOM_RPM_MM_FABRIC_CLK 16
+#define QCOM_RPM_MM_FABRIC_HALT 17
+#define QCOM_RPM_MM_FABRIC_IOCTL 18
+#define QCOM_RPM_MM_FABRIC_MODE 19
+#define QCOM_RPM_PLL_4 20
+#define QCOM_RPM_PM8058_LDO0 21
+#define QCOM_RPM_PM8058_LDO1 22
+#define QCOM_RPM_PM8058_LDO2 23
+#define QCOM_RPM_PM8058_LDO3 24
+#define QCOM_RPM_PM8058_LDO4 25
+#define QCOM_RPM_PM8058_LDO5 26
+#define QCOM_RPM_PM8058_LDO6 27
+#define QCOM_RPM_PM8058_LDO7 28
+#define QCOM_RPM_PM8058_LDO8 29
+#define QCOM_RPM_PM8058_LDO9 30
+#define QCOM_RPM_PM8058_LDO10 31
+#define QCOM_RPM_PM8058_LDO11 32
+#define QCOM_RPM_PM8058_LDO12 33
+#define QCOM_RPM_PM8058_LDO13 34
+#define QCOM_RPM_PM8058_LDO14 35
+#define QCOM_RPM_PM8058_LDO15 36
+#define QCOM_RPM_PM8058_LDO16 37
+#define QCOM_RPM_PM8058_LDO17 38
+#define QCOM_RPM_PM8058_LDO18 39
+#define QCOM_RPM_PM8058_LDO19 40
+#define QCOM_RPM_PM8058_LDO20 41
+#define QCOM_RPM_PM8058_LDO21 42
+#define QCOM_RPM_PM8058_LDO22 43
+#define QCOM_RPM_PM8058_LDO23 44
+#define QCOM_RPM_PM8058_LDO24 45
+#define QCOM_RPM_PM8058_LDO25 46
+#define QCOM_RPM_PM8058_LVS0 47
+#define QCOM_RPM_PM8058_LVS1 48
+#define QCOM_RPM_PM8058_NCP 49
+#define QCOM_RPM_PM8058_SMPS0 50
+#define QCOM_RPM_PM8058_SMPS1 51
+#define QCOM_RPM_PM8058_SMPS2 52
+#define QCOM_RPM_PM8058_SMPS3 53
+#define QCOM_RPM_PM8058_SMPS4 54
+#define QCOM_RPM_PM8821_LDO1 55
+#define QCOM_RPM_PM8821_SMPS1 56
+#define QCOM_RPM_PM8821_SMPS2 57
+#define QCOM_RPM_PM8901_LDO0 58
+#define QCOM_RPM_PM8901_LDO1 59
+#define QCOM_RPM_PM8901_LDO2 60
+#define QCOM_RPM_PM8901_LDO3 61
+#define QCOM_RPM_PM8901_LDO4 62
+#define QCOM_RPM_PM8901_LDO5 63
+#define QCOM_RPM_PM8901_LDO6 64
+#define QCOM_RPM_PM8901_LVS0 65
+#define QCOM_RPM_PM8901_LVS1 66
+#define QCOM_RPM_PM8901_LVS2 67
+#define QCOM_RPM_PM8901_LVS3 68
+#define QCOM_RPM_PM8901_MVS 69
+#define QCOM_RPM_PM8901_SMPS0 70
+#define QCOM_RPM_PM8901_SMPS1 71
+#define QCOM_RPM_PM8901_SMPS2 72
+#define QCOM_RPM_PM8901_SMPS3 73
+#define QCOM_RPM_PM8901_SMPS4 74
+#define QCOM_RPM_PM8921_CLK1 75
+#define QCOM_RPM_PM8921_CLK2 76
+#define QCOM_RPM_PM8921_LDO1 77
+#define QCOM_RPM_PM8921_LDO2 78
+#define QCOM_RPM_PM8921_LDO3 79
+#define QCOM_RPM_PM8921_LDO4 80
+#define QCOM_RPM_PM8921_LDO5 81
+#define QCOM_RPM_PM8921_LDO6 82
+#define QCOM_RPM_PM8921_LDO7 83
+#define QCOM_RPM_PM8921_LDO8 84
+#define QCOM_RPM_PM8921_LDO9 85
+#define QCOM_RPM_PM8921_LDO10 86
+#define QCOM_RPM_PM8921_LDO11 87
+#define QCOM_RPM_PM8921_LDO12 88
+#define QCOM_RPM_PM8921_LDO13 89
+#define QCOM_RPM_PM8921_LDO14 90
+#define QCOM_RPM_PM8921_LDO15 91
+#define QCOM_RPM_PM8921_LDO16 92
+#define QCOM_RPM_PM8921_LDO17 93
+#define QCOM_RPM_PM8921_LDO18 94
+#define QCOM_RPM_PM8921_LDO19 95
+#define QCOM_RPM_PM8921_LDO20 96
+#define QCOM_RPM_PM8921_LDO21 97
+#define QCOM_RPM_PM8921_LDO22 98
+#define QCOM_RPM_PM8921_LDO23 99
+#define QCOM_RPM_PM8921_LDO24 100
+#define QCOM_RPM_PM8921_LDO25 101
+#define QCOM_RPM_PM8921_LDO26 102
+#define QCOM_RPM_PM8921_LDO27 103
+#define QCOM_RPM_PM8921_LDO28 104
+#define QCOM_RPM_PM8921_LDO29 105
+#define QCOM_RPM_PM8921_LVS1 106
+#define QCOM_RPM_PM8921_LVS2 107
+#define QCOM_RPM_PM8921_LVS3 108
+#define QCOM_RPM_PM8921_LVS4 109
+#define QCOM_RPM_PM8921_LVS5 110
+#define QCOM_RPM_PM8921_LVS6 111
+#define QCOM_RPM_PM8921_LVS7 112
+#define QCOM_RPM_PM8921_MVS 113
+#define QCOM_RPM_PM8921_NCP 114
+#define QCOM_RPM_PM8921_SMPS1 115
+#define QCOM_RPM_PM8921_SMPS2 116
+#define QCOM_RPM_PM8921_SMPS3 117
+#define QCOM_RPM_PM8921_SMPS4 118
+#define QCOM_RPM_PM8921_SMPS5 119
+#define QCOM_RPM_PM8921_SMPS6 120
+#define QCOM_RPM_PM8921_SMPS7 121
+#define QCOM_RPM_PM8921_SMPS8 122
+#define QCOM_RPM_PXO_CLK 123
+#define QCOM_RPM_QDSS_CLK 124
+#define QCOM_RPM_SFPB_CLK 125
+#define QCOM_RPM_SMI_CLK 126
+#define QCOM_RPM_SYS_FABRIC_ARB 127
+#define QCOM_RPM_SYS_FABRIC_CLK 128
+#define QCOM_RPM_SYS_FABRIC_HALT 129
+#define QCOM_RPM_SYS_FABRIC_IOCTL 130
+#define QCOM_RPM_SYS_FABRIC_MODE 131
+#define QCOM_RPM_USB_OTG_SWITCH 132
+#define QCOM_RPM_VDDMIN_GPIO 133
+
+/*
+ * Constants used to select force mode for regulators.
+ */
+#define QCOM_RPM_FORCE_MODE_NONE 0
+#define QCOM_RPM_FORCE_MODE_LPM 1
+#define QCOM_RPM_FORCE_MODE_HPM 2
+#define QCOM_RPM_FORCE_MODE_AUTO 3
+#define QCOM_RPM_FORCE_MODE_BYPASS 4
+
+#endif
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
