Re: [PATCH v3 7/8] arm64: dts: qcom: sdm660: Add initial Inforce IFC6560 board support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2022-05-14 02:45:17, Dmitry Baryshkov wrote:
> The IFC6560 is a board from Inforce Computing, built around the SDA660
> SoC. This patch describes core clocks, some regulators from the two
> PMICs, debug uart, storage, bluetooth and audio DSP remoteproc.
> 
> The regulator settings are inherited from prior work by Konrad Dybcio
> and AngeloGioacchino Del Regno.
> 
> Co-developed-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/qcom/Makefile             |   1 +
>  .../boot/dts/qcom/sda660-inforce-ifc6560.dts  | 455 ++++++++++++++++++
>  2 files changed, 456 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index f9e6343acd03..5f717fe0e8d0 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -88,6 +88,7 @@ dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-herobrine-herobrine-r1.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-idp2.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sc7280-crd.dtb
> +dtb-$(CONFIG_ARCH_QCOM)	+= sda660-inforce-ifc6560.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-ganges-kirin.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-discovery.dtb
>  dtb-$(CONFIG_ARCH_QCOM)	+= sdm630-sony-xperia-nile-pioneer.dtb
> diff --git a/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts b/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts
> new file mode 100644
> index 000000000000..ade5c27dafcf
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/sda660-inforce-ifc6560.dts
> @@ -0,0 +1,455 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2021, Linaro Ltd.
> + * Copyright (c) 2020, Konrad Dybcio <konrad.dybcio@xxxxxxxxxxxxxx>
> + * Copyright (c) 2020, AngeloGioacchino Del Regno
> + *                     <angelogioacchino.delregno@xxxxxxxxxxxxxx>
> + */
> +
> +/dts-v1/;
> +
> +#include "sdm660.dtsi"
> +#include "pm660.dtsi"
> +#include "pm660l.dtsi"
> +
> +/ {
> +	model = "Inforce 6560 Single Board Computer";
> +	compatible = "inforce,ifc6560", "qcom,sda660";
> +	chassis-type = "embedded"; /* SBC */
> +
> +	aliases {
> +		serial0 = &blsp1_uart2;
> +		serial1 = &blsp2_uart1;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	gpio-keys {
> +		compatible = "gpio-keys";
> +
> +		volup {
> +			label = "Volume Up";
> +			gpios = <&pm660l_gpios 7 GPIO_ACTIVE_LOW>;
> +			linux,code = <KEY_VOLUMEUP>;
> +			debounce-interval = <15>;
> +		};
> +	};
> +
> +	/*
> +	 * Until we hook up type-c detection, we
> +	 * have to stick with this. But it works.
> +	 */
> +	extcon_usb: extcon-usb {
> +		compatible = "linux,extcon-usb-gpio";
> +		id-gpio = <&tlmm 58 GPIO_ACTIVE_HIGH>;
> +	};
> +
> +	hdmi-out {
> +		compatible = "hdmi-connector";
> +		type = "a";
> +
> +		port {
> +			hdmi_con: endpoint {
> +				remote-endpoint = <&adv7533_out>;
> +			};
> +		};
> +	};
> +
> +	vph_pwr: vph-pwr-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "vph_pwr";
> +		regulator-min-microvolt = <3800000>;
> +		regulator-max-microvolt = <3800000>;
> +
> +		regulator-always-on;
> +		regulator-boot-on;
> +	};
> +
> +	v3p3_bck_bst: v3p3-bck-bst-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v3p3_bck_bst";
> +
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +
> +		vin-supply = <&vph_pwr>;
> +	};
> +
> +	v1p2_ldo: v1p2-ldo-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v1p2_ldo";
> +
> +		regulator-min-microvolt = <1200000>;
> +		regulator-max-microvolt = <1200000>;
> +
> +		vin-supply = <&vph_pwr>;
> +	};
> +
> +	v5p0_boost: v5p0-boost-regulator {
> +		compatible = "regulator-fixed";
> +		regulator-name = "v5p0_boost";
> +
> +		regulator-min-microvolt = <5000000>;
> +		regulator-max-microvolt = <5000000>;
> +
> +		vin-supply = <&vph_pwr>;
> +	};
> +};
> +
> +&adsp_pil {
> +	firmware-name = "qcom/ifc6560/adsp.mbn";
> +};
> +
> +&blsp1_dma {
> +	/*
> +	 * The board will lock up if we toggle the BLSP clock, unless the
> +	 * BAM DMA interconnects support is in place.
> +	 */
> +	/delete-property/ clocks;
> +};
> +
> +&blsp_i2c6 {
> +	status = "okay";
> +
> +	adv7533: hdmi@39 {
> +		compatible = "adi,adv7535";
> +		reg = <0x39>, <0x66>;
> +		reg-names = "main", "edid";
> +
> +		interrupt-parent = <&pm660l_gpios>;
> +		interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
> +
> +		clocks = <&rpmcc RPM_SMD_BB_CLK2>;
> +		clock-names = "cec";
> +		/*
> +		 * Limit to 3 lanes to prevent the bridge from changing amount
> +		 * of lanes in the fly. MSM DSI host doesn't like that.
> +		 */
> +		adi,dsi-lanes = <3>;
> +		avdd-supply = <&vreg_l13a_1p8>;
> +		dvdd-supply = <&vreg_l13a_1p8>;
> +		pvdd-supply = <&vreg_l13a_1p8>;
> +		a2vdd-supply = <&vreg_l13a_1p8>;
> +		v3p3-supply = <&v3p3_bck_bst>;
> +
> +		ports {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			port@0 {
> +				reg = <0>;
> +
> +				adv7533_in: endpoint {
> +					remote-endpoint = <&dsi0_out>;
> +				};
> +			};
> +
> +			port@1 {
> +				reg = <1>;
> +
> +				adv7533_out: endpoint {
> +					remote-endpoint = <&hdmi_con>;
> +				};
> +			};
> +		};
> +	};
> +};
> +
> +&blsp1_uart2 {
> +	status = "okay";
> +};
> +
> +&blsp2_dma {
> +	/*
> +	 * The board will lock up if we toggle the BLSP clock, unless the
> +	 * BAM DMA interconnects support is in place.
> +	 */
> +	/delete-property/ clocks;
> +};
> +
> +&blsp2_uart1 {
> +	status = "okay";
> +
> +	bluetooth {
> +		compatible = "qcom,wcn3990-bt";
> +
> +		vddio-supply = <&vreg_l13a_1p8>;
> +		vddxo-supply = <&vreg_l9a_1p8>;
> +		vddrf-supply = <&vreg_l6a_1p3>;
> +		vddch0-supply = <&vreg_l19a_3p3>;
> +		max-speed = <3200000>;
> +	};
> +};
> +
> +&dsi0 {
> +	status = "okay";
> +	vdda-supply = <&vreg_l1a_1p225>;
> +};
> +
> +&dsi0_out {
> +	remote-endpoint = <&adv7533_in>;
> +	data-lanes = <0 1 2 3>;
> +};
> +
> +&dsi0_phy {
> +	status = "okay";
> +	vcca-supply = <&vreg_l1b_0p925>;

@Konrad: It looks like we have this regulator downstream in mdss_dsi but
not in the upstream DT, is it missing by accident?

> +};
> +
> +&mdss {
> +	status = "okay";
> +};
> +
> +&mmss_smmu {
> +	status = "okay";
> +};
> +
> +&pon_pwrkey {
> +	status = "okay";
> +};
> +
> +&pon_resin {
> +	status = "okay";
> +
> +	linux,code = <KEY_VOLUMEUP>;
> +};
> +
> +&qusb2phy {
> +	status = "okay";
> +
> +	vdd-supply = <&vreg_l1b_0p925>;
> +	vdda-phy-dpdm-supply = <&vreg_l7b_3p125>;
> +};
> +
> +&qusb2phy1 {
> +	status = "okay";
> +
> +	vdd-supply = <&vreg_l1b_0p925>;
> +	vdda-phy-dpdm-supply = <&vreg_l7b_3p125>;
> +};
> +
> +&rpm_requests {
> +	pm660-regulators {
> +		compatible = "qcom,rpm-pm660-regulators";
> +
> +		vdd_s1-supply = <&vph_pwr>;
> +		vdd_s2-supply = <&vph_pwr>;
> +		vdd_s3-supply = <&vph_pwr>;
> +		vdd_s4-supply = <&vph_pwr>;
> +		vdd_s5-supply = <&vph_pwr>;
> +		vdd_s6-supply = <&vph_pwr>;
> +
> +		vdd_l1_l6_l7-supply = <&vreg_s5a_1p35>;
> +		vdd_l2_l3-supply = <&vreg_s2b_1p05>;
> +		vdd_l5-supply = <&vreg_s2b_1p05>;
> +		vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>;
> +		vdd_l15_l16_l17_l18_l19-supply = <&vreg_bob>;
> +
> +		vreg_s4a_2p04: s4 {
> +			regulator-min-microvolt = <1805000>;
> +			regulator-max-microvolt = <2040000>;
> +			regulator-enable-ramp-delay = <200>;
> +			regulator-ramp-delay = <0>;
> +			regulator-always-on;
> +		};
> +
> +		vreg_s5a_1p35: s5 {
> +			regulator-min-microvolt = <1224000>;
> +			regulator-max-microvolt = <1350000>;
> +			regulator-enable-ramp-delay = <200>;
> +			regulator-ramp-delay = <0>;
> +		};
> +
> +		vreg_l1a_1p225: l1 {
> +			regulator-min-microvolt = <1150000>;
> +			regulator-max-microvolt = <1250000>;
> +			regulator-enable-ramp-delay = <250>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_l6a_1p3: l6 {
> +			regulator-min-microvolt = <1304000>;
> +			regulator-max-microvolt = <1368000>;
> +			regulator-enable-ramp-delay = <250>;
> +			regulator-ramp-delay = <0>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_l8a_1p8: l8 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1800000>;
> +			regulator-enable-ramp-delay = <250>;
> +			regulator-ramp-delay = <0>;
> +			regulator-system-load = <325000>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_l9a_1p8: l9 {
> +			regulator-min-microvolt = <1804000>;
> +			regulator-max-microvolt = <1896000>;
> +			regulator-enable-ramp-delay = <250>;
> +			regulator-ramp-delay = <0>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_l13a_1p8: l13 {
> +			/* This gives power to the LPDDR4: never turn it off! */
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <1944000>;
> +			regulator-enable-ramp-delay = <250>;
> +			regulator-ramp-delay = <0>;
> +			regulator-always-on;
> +			regulator-boot-on;
> +		};
> +
> +		vreg_l19a_3p3: l19 {
> +			regulator-min-microvolt = <3312000>;
> +			regulator-max-microvolt = <3400000>;
> +			regulator-enable-ramp-delay = <250>;
> +			regulator-ramp-delay = <0>;
> +			regulator-allow-set-load;
> +		};
> +	};
> +
> +	pm660l-regulators {
> +		compatible = "qcom,rpm-pm660l-regulators";
> +
> +		vdd_s1-supply = <&vph_pwr>;
> +		vdd_s2-supply = <&vph_pwr>;
> +		vdd_s3_s4-supply = <&vph_pwr>;
> +		vdd_s5-supply = <&vph_pwr>;
> +		vdd_s6-supply = <&vph_pwr>;
> +
> +		vdd_l1_l9_l10-supply = <&vreg_s2b_1p05>;
> +		vdd_l2-supply = <&vreg_bob>;
> +		vdd_l3_l5_l7_l8-supply = <&vreg_bob>;
> +		vdd_l4_l6-supply = <&vreg_bob>;
> +		vdd_bob-supply = <&vph_pwr>;
> +
> +		vreg_s2b_1p05: s2 {
> +			regulator-min-microvolt = <1050000>;
> +			regulator-max-microvolt = <1050000>;
> +			regulator-enable-ramp-delay = <200>;
> +			regulator-ramp-delay = <0>;
> +		};
> +
> +		vreg_l1b_0p925: l1 {
> +			regulator-min-microvolt = <800000>;
> +			regulator-max-microvolt = <925000>;
> +			regulator-enable-ramp-delay = <250>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_l2b_2p95: l2 {
> +			regulator-min-microvolt = <1648000>;
> +			regulator-max-microvolt = <3100000>;
> +			regulator-enable-ramp-delay = <250>;
> +			regulator-ramp-delay = <0>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_l4b_2p95: l4 {
> +			regulator-min-microvolt = <2944000>;
> +			regulator-max-microvolt = <2952000>;
> +			regulator-enable-ramp-delay = <250>;
> +			regulator-ramp-delay = <0>;
> +
> +			regulator-min-microamp = <200>;
> +			regulator-max-microamp = <600000>;
> +			regulator-system-load = <570000>;
> +			regulator-allow-set-load;
> +		};
> +
> +		/*
> +		 * Downstream specifies a range of 1721-3600mV,
> +		 * but the only assigned consumers are SDHCI2 VMMC
> +		 * and Coresight QPDI that both request pinned 2.95V.
> +		 * Tighten the range to 1.8-3.328 (closest to 3.3) to
> +		 * make the mmc driver happy.
> +		 */
> +		vreg_l5b_2p95: l5 {
> +			regulator-min-microvolt = <1800000>;
> +			regulator-max-microvolt = <3328000>;
> +			regulator-enable-ramp-delay = <250>;
> +			regulator-system-load = <800000>;
> +			regulator-ramp-delay = <0>;
> +			regulator-allow-set-load;
> +		};
> +
> +		vreg_l7b_3p125: l7 {
> +			regulator-min-microvolt = <2700000>;
> +			regulator-max-microvolt = <3125000>;
> +			regulator-enable-ramp-delay = <250>;
> +		};
> +
> +		vreg_l8b_3p3: l8 {
> +			regulator-min-microvolt = <2800000>;
> +			regulator-max-microvolt = <3400000>;
> +			regulator-enable-ramp-delay = <250>;
> +			regulator-ramp-delay = <0>;
> +		};
> +
> +		vreg_bob: bob {
> +			regulator-min-microvolt = <3300000>;
> +			regulator-max-microvolt = <3624000>;
> +			regulator-enable-ramp-delay = <500>;
> +			regulator-ramp-delay = <0>;
> +		};
> +	};
> +};
> +
> +&sdhc_1 {
> +	status = "okay";
> +	supports-cqe;
> +
> +	vmmc-supply = <&vreg_l4b_2p95>;
> +	vqmmc-supply = <&vreg_l8a_1p8>;
> +
> +	mmc-ddr-1_8v;
> +	mmc-hs400-1_8v;
> +	mmc-hs400-enhanced-strobe;
> +};
> +
> +&sdhc_2 {
> +	status = "okay";
> +
> +	pinctrl-names = "default";

Missing , "sleep".

> +	pinctrl-0 = <&sdc2_state_on &sdc2_card_det_n>;
> +	pinctrl1 = <&sdc2_state_off &sdc2_card_det_n>;

Missing hyphen.

> +
> +	vmmc-supply = <&vreg_l5b_2p95>;
> +	vqmmc-supply = <&vreg_l2b_2p95>;
> +
> +	cd-gpios = <&tlmm 54 GPIO_ACTIVE_LOW>;
> +	no-sdio;
> +	no-emmc;
> +};
> +
> +&tlmm {
> +	gpio-reserved-ranges = <0 4>, <8 4>;
> +
> +	sdc2_card_det_n: sd-card-det-n {
> +		pins = "gpio54";
> +		function = "gpio";
> +		bias-pull-up;
> +	};

It seems this pin is also already declared in sdc2-on/off in
sdm630.dtsi, with the same bias-pull-up in the -on case.  However, the
-off case sets bias-disable, won't that conflict?  (not in this moment,
because the clashing pinctrl pairs are "unused" with the typos above).

I have always been under the impression this GPIO is board-specific and
should be moved out of sdm630.dtsi into board-specific DTs, is that
true?

- Marijn

> +};
> +
> +&usb2 {
> +	status = "okay";
> +};
> +
> +&usb2_dwc3 {
> +	dr_mode = "host";
> +};
> +
> +&usb3 {
> +	status = "okay";
> +};
> +
> +&usb3_dwc3 {
> +	dr_mode = "peripheral";
> +	extcon = <&extcon_usb>;
> +};
> -- 
> 2.35.1
> 



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux