On Wed May 11, 2022 at 10:45 PM IST, Krzysztof Kozlowski wrote: > On 11/05/2022 18:15, Sireesh Kodali wrote: > > Convert the dt-bindings from txt to YAML. This is in preparation for > > including the relevant bindings for the MSM8953 platform's wcnss pil. > > > > Signed-off-by: Sireesh Kodali <sireeshkodali1@xxxxxxxxx> > > Thank you for your patch. There is something to discuss/improve. > > Please use existing bindings or example-schema as a starting point. Half > of my review could be skipped if you just followed what we already have > in the tree. > > Some of these qcom specific properties already exist but you decided to > write them differently... please don't, rather reuse the code. > Thank you for your review, I will make the chnages as appropriate in v2. > (...) > > > + > > +maintainers: > > + - Bjorn Andersson <bjorn.andersson@xxxxxxxxxx> > > + > > +description: > > + This document defines the binding for a component that loads and boots > > + firmware on the Qualcomm WCNSS core. > > + > > +properties: > > + compatible: > > + oneOf: > > + - items: > > + - enum: > > + - qcom,pronto-v2-pil > > + - enum: > > + - qcom,pronto > > This does not look correct. The fallback compatible should not change. > What is more, it was not documented in original binding, so this should > be done in separate patch. > This was not a change to the fallback compatible. msm8916.dtsi's wcnss node has "qcom,pronto" as the compatible string, which is why this was added. It is however not documented in the txt file. Is it sufficient to add a note in the commit message, or should it be split into a separate commit? > > + - items: > > No need for items, it's just one item. > > > + - enum: > > + - qcom,riva-pil > > + - qcom,pronto-v1-pil > > + - qcom,pronto-v2-pil > > + > > + reg: > > + description: must specify the base address and size of the CCU, DXE and PMU > > + register blocks > > New line after "decription:", drop "must specify" and start with capital > letter. > > You need maxItems: 3 > Will fix in v2 > > > + > > + reg-names: > > + items: > > + - const: ccu > > + - const: dxe > > + - const: pmu > > + > > + interrupts-extended: > > + description: > > + Interrupt lines > > Skip description, it's obvious. > > It should be only "interrupts", not extended. > > > + minItems: 2 > > + maxItems: 5 > > + > > + interrupt-names: > > + minItems: 2 > > + maxItems: 5 > > Names should be clearly defined. They were BTW defined in original > bindings, so you should not remove them. This makes me wonder what else > did you remove from original bindings... > > Please document all deviations from pure conversion in the commit msg. > It's a second "hidden" difference. > Sorry, this was meant to be a pure txt->YAML conversion. The missing interrupt names was accidental, and will be fixed in v2. > > + > > + firmware-name: > > + $ref: /schemas/types.yaml#/definitions/string > > + description: Relative firmware image path for the WCNSS core. Defaults to > > + "wcnss.mdt". > > > Blank line after "description:". This applies to other places as well. > > Remove "Defailts to ..." and just add "default" schema. > Will be fixed in v2 > > + > > + vddpx-supply: > > + description: Reference to the PX regulator to be held on behalf of the > > + booting of the WCNSS core > > + > > + vddmx-supply: > > + description: Reference to the MX regulator to be held on behalf of the > > + booting of the WCNSS core. > > + > > + vddcx-supply: > > + description: Reference to the CX regulator to be held on behalf of the > > + booting of the WCNSS core. > > s/Reference to the// > > > + > > + power-domains: > > + $ref: /schemas/types.yaml#/definitions/phandle-array > > + description: References to the power domains that need to be held on > > + behalf of the booting WCNSS core > > 1. Ditto. > 2. No need for ref > 3. maxItems > > > + > > + power-domain-names: > > + $ref: /schemas/types.yaml#/definitions/string-array > > No need for ref, skip description. > > > + description: Names of the power domains > > + items: > > + - const: cx > > + - const: mx > > + > > + qcom,smem-states: > > + $ref: /schemas/types.yaml#/definitions/phandle-array > > + description: States used by the AP to signal the WCNSS core that it should > > + shutdown > > + items: > > + - description: Stop the modem > > + > > + qcom,smem-state-names: > > + $ref: /schemas/types.yaml#/definitions/string-array > > No need for ref. Really, it does not appear in any of existing bindings > for smem-state-names, so how did you get it? > The smem nodes were copied from /remoteproc/qcom,sdm845-adsp-pil.yaml > > + description: The names of the state bits used for SMP2P output > > + items: > > + - const: stop > > + > > + memory-region: > > + maxItems: 1 > > + description: Reference to the reserved-memory for the WCNSS core > > + > > + smd-edge: > > + type: object > > + description: > > + Qualcomm Shared Memory subnode which represents communication edge, > > + channels and devices related to the ADSP. > > You should reference /schemas/soc/qcom/qcom,smd.yaml Will be done in v2 > > > + > > + iris: > > Generic node name... what is "iris"? > Iris is the RF module, I'll make the description better > > + type: object > > + description: > > + The iris subnode of the WCNSS PIL is used to describe the attached rf module > > s/rf/RF/ > > > + and its resource dependencies. > > + > > + properties: > > + compatible: > > + enum: > > + - qcom,wcn3620 > > + - qcom,wcn3660 > > + - qcom,wcn3660b > > + - qcom,wcn3680 > > + > > + clocks: > > + description: XO clock > > + > > + clock-names: > > + items: > > + - const: xo > > + > > + required: > > + - compatible > > clocks and clock-names were required. > Missing supplies, which were btw as well required. > This was unintentional, it will be fixed in v2. > > + > > +required: > > + - compatible > > + - reg > > + - reg-names > > + - interrupts-extended > > + - interrupt-names > > + - vddpx-supply > > + - memory-region > > + - smd-edge > > + - iris > > + > > +additionalProperties: false > > + > > +if: > > Within allOf, please. > Will be fixed in v2 > > > Best regards, > Krzysztof Thanks again for the review, Sireesh
