On Sat, May 07, 2022 at 07:04:35PM +0200, Frank Wunderlich wrote: > From: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx> > > Convert txt binding to yaml binding for Mediatek switches. > > Signed-off-by: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx> > --- > v3: > - include standalone patch in mt7530 series > - drop some descriptions (gpio-cells,reset-gpios,reset-names) > - drop | from descriptions > - move patternProperties above allOf > > v2: > - rename mediatek.yaml => mediatek,mt7530.yaml > - drop "boolean" in description > - drop description for interrupt-properties > - drop #interrupt-cells as requirement > - example: eth=>ethernet,mdio0=>mdio,comment indention > - replace 0 by GPIO_ACTIVE_HIGH in first example > - use port(s)-pattern from dsa.yaml > - adress/size-cells not added to required because this > is defined at mdio-level inc current dts , not switch level > --- > .../bindings/net/dsa/mediatek,mt7530.yaml | 423 ++++++++++++++++++ > .../devicetree/bindings/net/dsa/mt7530.txt | 327 -------------- > 2 files changed, 423 insertions(+), 327 deletions(-) > create mode 100644 Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml > delete mode 100644 Documentation/devicetree/bindings/net/dsa/mt7530.txt > > diff --git a/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml b/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml > new file mode 100644 > index 000000000000..a7696d1b4a8c > --- /dev/null > +++ b/Documentation/devicetree/bindings/net/dsa/mediatek,mt7530.yaml > @@ -0,0 +1,423 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/net/dsa/mediatek,mt7530.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Mediatek MT7530 Ethernet switch > + > +maintainers: > + - Sean Wang <sean.wang@xxxxxxxxxxxx> > + - Landen Chao <Landen.Chao@xxxxxxxxxxxx> > + - DENG Qingfang <dqfext@xxxxxxxxx> > + > +description: | > + Port 5 of mt7530 and mt7621 switch is muxed between: > + 1. GMAC5: GMAC5 can interface with another external MAC or PHY. > + 2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC > + of the SOC. Used in many setups where port 0/4 becomes the WAN port. > + Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to > + GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not > + connected to external component! > + > + Port 5 modes/configurations: > + 1. Port 5 is disabled and isolated: An external phy can interface to the 2nd > + GMAC of the SOC. > + In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd > + GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC! > + 2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC. > + It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode > + and RGMII delay. > + 3. Port 5 is muxed to GMAC5 and can interface to an external phy. > + Port 5 becomes an extra switch port. > + Only works on platform where external phy TX<->RX lines are swapped. > + Like in the Ubiquiti ER-X-SFP. > + 4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port. > + Currently a 2nd CPU port is not supported by DSA code. > + > + Depending on how the external PHY is wired: > + 1. normal: The PHY can only connect to 2nd GMAC but not to the switch > + 2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as > + a ethernet port. But can't interface to the 2nd GMAC. > + > + Based on the DT the port 5 mode is configured. > + > + Driver tries to lookup the phy-handle of the 2nd GMAC of the master device. > + When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2. > + phy-mode must be set, see also example 2 below! > + * mt7621: phy-mode = "rgmii-txid"; > + * mt7623: phy-mode = "rgmii"; > + > + CPU-Ports need a phy-mode property: > + Allowed values on mt7530 and mt7621: > + - "rgmii" > + - "trgmii" > + On mt7531: > + - "1000base-x" > + - "2500base-x" > + - "sgmii" > + > + > +properties: > + compatible: > + enum: > + - mediatek,mt7530 > + - mediatek,mt7531 > + - mediatek,mt7621 > + > + "#address-cells": > + const: 1 > + > + "#size-cells": > + const: 0 I don't see any child nodes with addresses, so these can be removed. > + > + core-supply: > + description: > + Phandle to the regulator node necessary for the core power. > + > + "#gpio-cells": > + const: 2 > + > + gpio-controller: > + type: boolean > + description: > + if defined, MT7530's LED controller will run on GPIO mode. > + > + "#interrupt-cells": > + const: 1 > + > + interrupt-controller: > + type: boolean Already has a type. Just: interrupt-controller: true > + > + interrupts: > + maxItems: 1 > + > + io-supply: > + description: > + Phandle to the regulator node necessary for the I/O power. > + See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt > + for details for the regulator setup on these boards. > + > + mediatek,mcm: > + type: boolean > + description: > + if defined, indicates that either MT7530 is the part on multi-chip > + module belong to MT7623A has or the remotely standalone chip as the > + function MT7623N reference board provided for. > + > + reset-gpios: > + maxItems: 1 > + > + reset-names: > + const: mcm > + > + resets: > + description: > + Phandle pointing to the system reset controller with line index for > + the ethsys. > + maxItems: 1 > + > +patternProperties: > + "^(ethernet-)?ports$": > + type: object additionalProperties: false > + > + patternProperties: > + "^(ethernet-)?port@[0-9]+$": > + type: object > + description: Ethernet switch ports > + > + unevaluatedProperties: false > + > + properties: > + reg: > + description: > + Port address described must be 5 or 6 for CPU port and from 0 > + to 5 for user ports. > + > + allOf: > + - $ref: dsa-port.yaml# > + - if: > + properties: > + label: > + items: > + - const: cpu > + then: > + required: > + - reg > + - phy-mode > + > +required: > + - compatible > + - reg > + > +allOf: > + - $ref: "dsa.yaml#" > + - if: > + required: > + - mediatek,mcm > + then: > + required: > + - resets > + - reset-names > + else: > + required: > + - reset-gpios > + > + - if: > + required: > + - interrupt-controller > + then: > + required: > + - interrupts This can be expressed as: dependencies: interrupt-controller: [ interrupts ] > + > + - if: > + properties: > + compatible: > + items: > + - const: mediatek,mt7530 > + then: > + required: > + - core-supply > + - io-supply > + > +unevaluatedProperties: false > + > +examples: > + - | > + #include <dt-bindings/gpio/gpio.h> > + mdio { > + #address-cells = <1>; > + #size-cells = <0>; > + switch@0 { > + compatible = "mediatek,mt7530"; > + #address-cells = <1>; > + #size-cells = <0>; > + reg = <0>; > + > + core-supply = <&mt6323_vpa_reg>; > + io-supply = <&mt6323_vemc3v3_reg>; > + reset-gpios = <&pio 33 GPIO_ACTIVE_HIGH>; > + > + ports { Use the preferred form: ethernet-ports > + #address-cells = <1>; > + #size-cells = <0>; > + port@0 {
