Re: [PATCH v2 02/23] dt-bindings: ata: ahci-platform: Detach common AHCI bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, May 04, 2022 at 05:29:23AM +0900, Damien Le Moal wrote:
> On 2022/05/04 5:09, Serge Semin wrote:
> > In order to create a more sophisticated AHCI controller DT bindings let's
> > divide the already available generic AHCI platform YAML schema into the
> > platform part and a set of the common AHCI properties. The former part
> > will be used to evaluate the AHCI DT nodes mainly compatible with the
> > generic AHCI controller while the later schema will be used for more
> > thorough AHCI DT nodes description. For instance such YAML schemas design
> > will be useful for our DW AHCI SATA controller derivative with four clock
> > sources, two reset lines, one system controller reference and specific
> > max Rx/Tx DMA xfers size constraints.
> > 
> > Note the phys and target-supply property requirement is preserved in the
> > generic AHCI platform bindings because some platforms can lack of the
> > explicitly specified PHYs or target device power regulators.
> > 
> > Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx>
> > 
> > ---
> > 
> > Folks, I don't really see why the phys/target-supply requirement has been
> > added to the generic AHCI DT schema in the first place. Probably just to
> > imply some meaning for the sub-nodes definition. Anyway in one of the
> > further patches I am adding the DW AHCI SATA controller DT bindings which
> > won't require having these properties specified in the sub-nodes, but will
> > describe additional port-specific properties. That's why I get to keep the
> > constraints in the ahci-platform.yaml schema instead of moving them to the
> > common schema.
> > 
> > Changelog v2:
> > - This is a new patch created after rebasing v1 onto the 5.18-rc3 kernel.
> > ---
> >  .../devicetree/bindings/ata/ahci-common.yaml  | 117 ++++++++++++++++++
> >  .../bindings/ata/ahci-platform.yaml           |  68 +---------
> >  2 files changed, 123 insertions(+), 62 deletions(-)
> >  create mode 100644 Documentation/devicetree/bindings/ata/ahci-common.yaml
> > 
> > diff --git a/Documentation/devicetree/bindings/ata/ahci-common.yaml b/Documentation/devicetree/bindings/ata/ahci-common.yaml
> > new file mode 100644
> > index 000000000000..72e24b246040
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/ata/ahci-common.yaml
> > @@ -0,0 +1,117 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/ata/ahci-common.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Common Properties for Serial ATA AHCI controllers
> > +
> > +maintainers:
> > +  - Hans de Goede <hdegoede@xxxxxxxxxx>
> > +  - Jens Axboe <axboe@xxxxxxxxx>
> 

> This should probably be me rather than Jens since Jens is no longer maintaining
> libata/ahci.

Ok. I'll replace his email address with yours in v3.

-Sergey

> 
> > +
> > +description:
> > +  This document defines device tree properties for a common AHCI SATA
> > +  controller implementation. It's hardware interface is supposed to
> > +  conform to the technical standard defined by Intel (see Serial ATA
> > +  Advanced Host Controller Interface specification for details). The
> > +  document doesn't constitute a DT-node binding by itself but merely
> > +  defines a set of common properties for the AHCI-compatible devices.
> > +
> > +select: false
> > +
> > +allOf:
> > +  - $ref: sata-common.yaml#
> > +
> > +properties:
> > +  reg:
> > +    description:
> > +      Generic AHCI registers space conforming to the Serial ATA AHCI
> > +      specification.
> > +
> > +  reg-names:
> > +    description: CSR space IDs
> > +
> > +  interrupts:
> > +    description:
> > +      Generic AHCI state change interrupt. Can be implemented either as a
> > +      single line attached to the controller as a set of the dedicated signals
> > +      for the global and particular port events.
> > +
> > +  clocks:
> > +    description:
> > +      List of all the reference clocks connected to the controller.
> > +
> > +  clock-names:
> > +    description: Reference clocks IDs
> > +
> > +  resets:
> > +    description:
> > +      List of the reset control lines to reset the controller clock
> > +      domains.
> > +
> > +  reset-names:
> > +    description: Reset line IDs
> > +
> > +  power-domains:
> > +    description:
> > +      List of the power domain the AHCI controller being a part of.
> > +
> > +  ahci-supply:
> > +    description: Power regulator for AHCI controller
> > +
> > +  target-supply:
> > +    description: Power regulator for SATA target device
> > +
> > +  phy-supply:
> > +    description: Power regulator for SATA PHY
> > +
> > +  phys:
> > +    description: Reference to the SATA PHY node
> > +    maxItems: 1
> > +
> > +  phy-names:
> > +    maxItems: 1
> > +
> > +  ports-implemented:
> > +    $ref: '/schemas/types.yaml#/definitions/uint32'
> > +    description:
> > +      Mask that indicates which ports the HBA supports. Useful if PI is not
> > +      programmed by the BIOS, which is true for some embedded SoC's.
> > +    maximum: 0x1f
> > +
> > +patternProperties:
> > +  "^sata-port@[0-9a-f]+$":
> > +    type: object
> > +    description:
> > +      It is optionally possible to describe the ports as sub-nodes so
> > +      to enable each port independently when dealing with multiple PHYs.
> > +
> > +    properties:
> > +      reg:
> > +        description: AHCI SATA port identifier
> > +        maxItems: 1
> > +
> > +      phys:
> > +        description: Individual AHCI SATA port PHY
> > +        maxItems: 1
> > +
> > +      phy-names:
> > +        description: AHCI SATA port PHY ID
> > +        maxItems: 1
> > +
> > +      target-supply:
> > +        description: Power regulator for SATA port target device
> > +
> > +    required:
> > +      - reg
> > +
> > +    additionalProperties: true
> > +
> > +required:
> > +  - reg
> > +  - interrupts
> > +
> > +additionalProperties: true
> > +
> > +...
> > diff --git a/Documentation/devicetree/bindings/ata/ahci-platform.yaml b/Documentation/devicetree/bindings/ata/ahci-platform.yaml
> > index 9304e4731965..76075d3c8987 100644
> > --- a/Documentation/devicetree/bindings/ata/ahci-platform.yaml
> > +++ b/Documentation/devicetree/bindings/ata/ahci-platform.yaml
> > @@ -36,8 +36,7 @@ select:
> >      - compatible
> >  
> >  allOf:
> > -  - $ref: "sata-common.yaml#"
> > -
> > +  - $ref: "ahci-common.yaml#"
> >  
> >  properties:
> >    compatible:
> > @@ -69,90 +68,35 @@ properties:
> >      maxItems: 1
> >  
> >    clocks:
> > -    description:
> > -      Clock IDs array as required by the controller.
> >      minItems: 1
> >      maxItems: 3
> >  
> >    clock-names:
> > -    description:
> > -      Names of clocks corresponding to IDs in the clock property.
> >      minItems: 1
> >      maxItems: 3
> >  
> >    interrupts:
> >      maxItems: 1
> >  
> > -  ahci-supply:
> > -    description:
> > -      regulator for AHCI controller
> > -
> > -  phy-supply:
> > -    description:
> > -      regulator for PHY power
> > -
> > -  phys:
> > -    description:
> > -      List of all PHYs on this controller
> > -    maxItems: 1
> > -
> > -  phy-names:
> > -    description:
> > -      Name specifier for the PHYs
> > -    maxItems: 1
> > -
> > -  ports-implemented:
> > -    $ref: '/schemas/types.yaml#/definitions/uint32'
> > -    description: |
> > -      Mask that indicates which ports that the HBA supports
> > -      are available for software to use. Useful if PORTS_IMPL
> > -      is not programmed by the BIOS, which is true with
> > -      some embedded SoCs.
> > -    maximum: 0x1f
> > -
> >    power-domains:
> >      maxItems: 1
> >  
> >    resets:
> >      maxItems: 1
> >  
> > -  target-supply:
> > -    description:
> > -      regulator for SATA target power
> > -
> > -required:
> > -  - compatible
> > -  - reg
> > -  - interrupts
> > -
> >  patternProperties:
> >    "^sata-port@[0-9a-f]+$":
> >      type: object
> > -    additionalProperties: false
> > -    description:
> > -      Subnode with configuration of the Ports.
> > -
> > -    properties:
> > -      reg:
> > -        maxItems: 1
> > -
> > -      phys:
> > -        maxItems: 1
> > -
> > -      phy-names:
> > -        maxItems: 1
> > -
> > -      target-supply:
> > -        description:
> > -          regulator for SATA target power
> > -
> > -    required:
> > -      - reg
> >  
> >      anyOf:
> >        - required: [ phys ]
> >        - required: [ target-supply ]
> >  
> > +required:
> > +  - compatible
> > +  - reg
> > +  - interrupts
> > +
> >  unevaluatedProperties: false
> >  
> >  examples:
> 
> 
> -- 
> Damien Le Moal
> Western Digital Research



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux