Bandwidth monitoring h/w sits between various subsytems like cpu, gpu
etc and ddr subsystem. This h/w can be configured to monitor the data
traffic between ddr and other subsytems. The bandwidth values obtained
from this monitoring is used to bump up or down the corresponding
interconnect speeds.
Co-developed-by: Thara Gopinath <thara.gopinath@xxxxxxxxxx>
Signed-off-by: Thara Gopinath <thara.gopinath@xxxxxxxxxx>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
---
MAINTAINERS | 7 +
drivers/soc/qcom/Kconfig | 10 ++
drivers/soc/qcom/Makefile | 1 +
drivers/soc/qcom/icc-bwmon.c | 328 +++++++++++++++++++++++++++++++++++
4 files changed, 346 insertions(+)
create mode 100644 drivers/soc/qcom/icc-bwmon.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 6157e706ed02..bc123f706256 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -16376,6 +16376,13 @@ S: Maintained
F: Documentation/devicetree/bindings/i2c/i2c-qcom-cci.txt
F: drivers/i2c/busses/i2c-qcom-cci.c
+QUALCOMM INTERCONNECT BWMON DRIVER
+M: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>
+L: linux-arm-msm@xxxxxxxxxxxxxxx
+S: Maintained
+F: Documentation/devicetree/bindings/interconnect/qcom,sdm845-cpu-bwmon.yaml
+F: drivers/soc/qcom/icc-bwmon.c
+
QUALCOMM IOMMU
M: Rob Clark <robdclark@xxxxxxxxx>
L: iommu@xxxxxxxxxxxxxxxxxxxxxxxxxx
diff --git a/drivers/soc/qcom/Kconfig b/drivers/soc/qcom/Kconfig
index e718b8735444..04375824e71a 100644
--- a/drivers/soc/qcom/Kconfig
+++ b/drivers/soc/qcom/Kconfig
@@ -228,4 +228,14 @@ config QCOM_APR
application processor and QDSP6. APR is
used by audio driver to configure QDSP6
ASM, ADM and AFE modules.
+
+config QCOM_ICC_BWMON
+ tristate "QCOM Interconnect Bandwidth Monitor driver"
+ depends on ARCH_QCOM || COMPILE_TEST
+ select PM_OPP
+ help
+ Sets up driver monitoring bandwidth on various interconnects and
+ based on that voting for interconnect bandwidth, adjusting their
+ speed to current demand.
+
endmenu
diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile
index 70d5de69fd7b..d66604aff2b0 100644
--- a/drivers/soc/qcom/Makefile
+++ b/drivers/soc/qcom/Makefile
@@ -28,3 +28,4 @@ obj-$(CONFIG_QCOM_LLCC) += llcc-qcom.o
obj-$(CONFIG_QCOM_RPMHPD) += rpmhpd.o
obj-$(CONFIG_QCOM_RPMPD) += rpmpd.o
obj-$(CONFIG_QCOM_KRYO_L2_ACCESSORS) += kryo-l2-accessors.o
+obj-$(CONFIG_QCOM_ICC_BWMON) += icc-bwmon.o
diff --git a/drivers/soc/qcom/icc-bwmon.c b/drivers/soc/qcom/icc-bwmon.c
new file mode 100644
index 000000000000..6df8d9f6e6e1
--- /dev/null
+++ b/drivers/soc/qcom/icc-bwmon.c
@@ -0,0 +1,328 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (C) 2021-2022 Linaro Ltd
+ */
+#include <linux/interconnect.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/sizes.h>
+#include <linux/time64.h>
+
+#define HW_TIMER_HZ 19200000
+
+#define BWMON_GLOBAL_IRQ_STATUS 0x0
+#define BWMON_GLOBAL_IRQ_CLEAR 0x8
+#define BWMON_GLOBAL_IRQ_ENABLE 0xc
+#define BWMON_GLOBAL_IRQ_ENABLE_ENABLE BIT(0)
+
+#define BWMON_IRQ_STATUS 0x100
+#define BWMON_IRQ_CLEAR 0x108
+#define BWMON_IRQ_ENABLE 0x10c
+#define BWMON_IRQ_ENABLE_ZONE1_SHIFT 5
+#define BWMON_IRQ_ENABLE_ZONE3_SHIFT 7
+
+#define BWMON_ENABLE 0x2a0
+#define BWMON_ENABLE_ENABLE BIT(0)
+
+#define BWMON_CLEAR 0x2a4
+#define BWMON_CLEAR_CLEAR BIT(0)
+
+#define BWMON_SAMPLE_WINDOW 0x2a8
+#define BWMON_THRESHOLD_HIGH 0x2ac
+#define BWMON_THRESHOLD_MED 0x2b0
+#define BWMON_THRESHOLD_LOW 0x2b4
+
+#define BWMON_ZONE_ACTIONS 0x2b8
+#define BWMON_ZONE_ACTIONS_DEFAULT 0x95250901
+
+#define BWMON_THRESHOLD_COUNT 0x2bc
+#define BWMON_THRESHOLD_COUNT_ZONE1_SHIFT 8
+#define BWMON_THRESHOLD_COUNT_ZONE2_SHIFT 16
+#define BWMON_THRESHOLD_COUNT_ZONE3_SHIFT 24
+#define BWMON_THRESHOLD_COUNT_ZONE0_DEFAULT 0xFF
+#define BWMON_THRESHOLD_COUNT_ZONE2_DEFAULT 0xFF
+
+/* BWMON registers count data in MB/s */
+#define BWMON_ZONE_COUNT 0x2d8
+#define BWMON_ZONE_MAX(zone) (0x2e0 + 4 * (zone))
+
+struct icc_bwmon_data {
+ unsigned int sample_ms;
+ unsigned int default_highbw_kbps;
+ unsigned int default_medbw_kbps;
+ unsigned int default_lowbw_kbps;
+ u8 zone1_thres_count;
+ u8 zone3_thres_count;
+};
+
+struct icc_bwmon {
+ struct device *dev;
+ void __iomem *base;
+ int irq;
+
+ unsigned int sample_ms;
+ unsigned int max_bw_kbps;
+ unsigned int min_bw_kbps;
+ unsigned int target_kbps;
+ unsigned int current_kbps;
+};
+
+static void bwmon_clear(struct icc_bwmon *bwmon)
+{
+ /*
+ * Clear zone and global interrupts. The order and barriers are
+ * important. Quoting downstream Qualcomm msm-4.9 tree:
+ *
+ * Synchronize the local interrupt clear in mon_irq_clear()
+ * with the global interrupt clear here. Otherwise, the CPU
+ * may reorder the two writes and clear the global interrupt
+ * before the local interrupt, causing the global interrupt
+ * to be retriggered by the local interrupt still being high.
+ *
+ * Similarly, because the global registers are in a different
+ * region than the local registers, we need to ensure any register
+ * writes to enable the monitor after this call are ordered with the
+ * clearing here so that local writes don't happen before the
+ * interrupt is cleared.
+ */
+ writel(0xa0, bwmon->base + BWMON_IRQ_CLEAR);
+ writel(BIT(0), bwmon->base + BWMON_GLOBAL_IRQ_CLEAR);
+
+ /* Clear counters */
+ writel(BWMON_CLEAR_CLEAR, bwmon->base + BWMON_CLEAR);
+}
+
+static void bwmon_disable(struct icc_bwmon *bwmon)
+{
+ /* Disable interrupts. Strict ordering, see bwmon_clear(). */
+ writel(0x0, bwmon->base + BWMON_GLOBAL_IRQ_ENABLE);
+ writel(0x0, bwmon->base + BWMON_IRQ_ENABLE);
+
+ /* Disable bwmon */
+ writel(0x0, bwmon->base + BWMON_ENABLE);
+}
+
+static void bwmon_enable(struct icc_bwmon *bwmon, unsigned int irq_enable)
+{
+ /* Enable interrupts */
+ writel(BWMON_GLOBAL_IRQ_ENABLE_ENABLE,
+ bwmon->base + BWMON_GLOBAL_IRQ_ENABLE);
+ writel(irq_enable, bwmon->base + BWMON_IRQ_ENABLE);
+
+ /* Enable bwmon */
+ writel(BWMON_ENABLE_ENABLE, bwmon->base + BWMON_ENABLE);
+}
+
+static void bwmon_set_threshold(struct icc_bwmon *bwmon, unsigned int reg,
+ unsigned int kbps)
+{
+ unsigned int mbps = kbps / SZ_1K;
+ unsigned int thres;
+
+ thres = mult_frac(mbps, bwmon->sample_ms, MSEC_PER_SEC);
+ writel_relaxed(thres, bwmon->base + reg);
+}
+
+static void bwmon_start(struct icc_bwmon *bwmon,
+ const struct icc_bwmon_data *data)
+{
+ unsigned int thres_count, irq_enable;
+ int window;
+
+ bwmon_clear(bwmon);
+
+ window = mult_frac(bwmon->sample_ms, HW_TIMER_HZ, MSEC_PER_SEC);
+ writel_relaxed(window, bwmon->base + BWMON_SAMPLE_WINDOW);
+
+ bwmon_set_threshold(bwmon, BWMON_THRESHOLD_HIGH,
+ data->default_highbw_kbps);
+ bwmon_set_threshold(bwmon, BWMON_THRESHOLD_MED,
+ data->default_medbw_kbps);
+ bwmon_set_threshold(bwmon, BWMON_THRESHOLD_LOW,
+ data->default_lowbw_kbps);
+
+ thres_count = data->zone3_thres_count << BWMON_THRESHOLD_COUNT_ZONE3_SHIFT |
+ BWMON_THRESHOLD_COUNT_ZONE2_DEFAULT << BWMON_THRESHOLD_COUNT_ZONE2_SHIFT |
+ data->zone1_thres_count << BWMON_THRESHOLD_COUNT_ZONE1_SHIFT |
+ BWMON_THRESHOLD_COUNT_ZONE0_DEFAULT;
+ writel_relaxed(thres_count, bwmon->base + BWMON_THRESHOLD_COUNT);
+ writel_relaxed(BWMON_ZONE_ACTIONS_DEFAULT,
+ bwmon->base + BWMON_ZONE_ACTIONS);
+
+ /* Write barriers in bwmon_clear() */
+ irq_enable = BIT(BWMON_IRQ_ENABLE_ZONE1_SHIFT) |
+ BIT(BWMON_IRQ_ENABLE_ZONE3_SHIFT);
+ bwmon_clear(bwmon);
+ bwmon_enable(bwmon, irq_enable);
+}
+
+static irqreturn_t bwmon_intr(int irq, void *dev_id)
+{
+ struct icc_bwmon *bwmon = dev_id;
+ unsigned int status, max;
+ int zone;
+
+ status = readl(bwmon->base + BWMON_IRQ_STATUS);
+
+ if (!status)
+ return IRQ_NONE;
+
+ bwmon_disable(bwmon);
+
+ zone = get_bitmask_order(status >> 4) - 1;
+ max = readl(bwmon->base + BWMON_ZONE_MAX(zone)) * SZ_1K;
+ bwmon->target_kbps = mult_frac(max, MSEC_PER_SEC, bwmon->sample_ms);
+
+ return IRQ_WAKE_THREAD;
+}
+
+static irqreturn_t bwmon_intr_thread(int irq, void *dev_id)
+{
+ struct icc_bwmon *bwmon = dev_id;
+ unsigned int irq_enable = 0;
+ struct dev_pm_opp *opp, *target_opp;
+ unsigned int bw_kbps, up_kbps, down_kbps;
+
+ bw_kbps = bwmon->target_kbps;
+
+ target_opp = dev_pm_opp_find_bw_ceil(bwmon->dev, &bw_kbps, 0);
+ if (IS_ERR(target_opp) && PTR_ERR(target_opp) == -ERANGE)
+ target_opp = dev_pm_opp_find_bw_floor(bwmon->dev, &bw_kbps, 0);
+
+ bwmon->target_kbps = bw_kbps;
+
+ bw_kbps--;
+ opp = dev_pm_opp_find_bw_floor(bwmon->dev, &bw_kbps, 0);
+ if (IS_ERR(opp) && PTR_ERR(opp) == -ERANGE)
+ down_kbps = bwmon->target_kbps;
+ else
+ down_kbps = bw_kbps;
+
+ up_kbps = bwmon->target_kbps + 1;
+
+ if (bwmon->target_kbps >= bwmon->max_bw_kbps)
+ irq_enable = BIT(BWMON_IRQ_ENABLE_ZONE1_SHIFT);
+ else if (bwmon->target_kbps <= bwmon->min_bw_kbps)
+ irq_enable = BIT(BWMON_IRQ_ENABLE_ZONE3_SHIFT);
+ else
+ irq_enable = BIT(BWMON_IRQ_ENABLE_ZONE1_SHIFT) |
+ BIT(BWMON_IRQ_ENABLE_ZONE3_SHIFT);
+
+ bwmon_set_threshold(bwmon, BWMON_THRESHOLD_HIGH, up_kbps);
+ bwmon_set_threshold(bwmon, BWMON_THRESHOLD_MED, down_kbps);
+ bwmon_clear(bwmon);
+ bwmon_enable(bwmon, irq_enable);
+
+ if (bwmon->target_kbps == bwmon->current_kbps)
+ goto out;
+
+ dev_pm_opp_set_opp(bwmon->dev, target_opp);
+ bwmon->current_kbps = bwmon->target_kbps;
+
+out:
+ dev_pm_opp_put(target_opp);
+ if (!IS_ERR(opp))
+ dev_pm_opp_put(opp);
+
+ return IRQ_HANDLED;
+}
+
+static int bwmon_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct dev_pm_opp *opp;
+ struct icc_bwmon *bwmon;
+ const struct icc_bwmon_data *data;
+ int ret;
+
+ bwmon = devm_kzalloc(dev, sizeof(*bwmon), GFP_KERNEL);
+ if (!bwmon)
+ return -ENOMEM;
+
+ data = of_device_get_match_data(dev);
+
+ bwmon->base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(bwmon->base)) {
+ dev_err(dev, "failed to map bwmon registers\n");
+ return PTR_ERR(bwmon->base);
+ }
+
+ bwmon->irq = platform_get_irq(pdev, 0);
+ if (bwmon->irq < 0) {
+ dev_err(dev, "failed to acquire bwmon IRQ\n");
+ return bwmon->irq;
+ }
+
+ ret = devm_pm_opp_of_add_table(dev);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to add OPP table\n");
+
+ bwmon->max_bw_kbps = UINT_MAX;
+ opp = dev_pm_opp_find_bw_floor(dev, &bwmon->max_bw_kbps, 0);
+ if (IS_ERR(opp))
+ return dev_err_probe(dev, ret, "failed to find max peak bandwidth\n");
+
+ bwmon->min_bw_kbps = 0;
+ opp = dev_pm_opp_find_bw_ceil(dev, &bwmon->min_bw_kbps, 0);
+ if (IS_ERR(opp))
+ return dev_err_probe(dev, ret, "failed to find min peak bandwidth\n");
+
+ bwmon->sample_ms = data->sample_ms;
+ bwmon->dev = dev;
+
+ bwmon_disable(bwmon);
+ ret = devm_request_threaded_irq(dev, bwmon->irq, bwmon_intr,
+ bwmon_intr_thread,
+ IRQF_ONESHOT, dev_name(dev), bwmon);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to request IRQ\n");
+
+ platform_set_drvdata(pdev, bwmon);
+ bwmon_start(bwmon, data);
+
+ return 0;
+}
+
+static int bwmon_remove(struct platform_device *pdev)
+{
+ struct icc_bwmon *bwmon = platform_get_drvdata(pdev);
+
+ bwmon_disable(bwmon);
+
+ return 0;
+}
+
+/* BWMON v4 */
+static const struct icc_bwmon_data sdm845_bwmon_data = {
+ .sample_ms = 4,
+ .default_highbw_kbps = 4800 * SZ_1K,
+ .default_medbw_kbps = 512 * SZ_1K,
+ .default_lowbw_kbps = 0,
+ .zone1_thres_count = 0x10,
+ .zone3_thres_count = 0x1,
+};
+
+static const struct of_device_id bwmon_of_match[] = {
+ { .compatible = "qcom,sdm845-cpu-bwmon", .data = &sdm845_bwmon_data },
+ {}
+};
+MODULE_DEVICE_TABLE(of, bwmon_of_match);
+
+static struct platform_driver bwmon_driver = {
+ .probe = bwmon_probe,
+ .remove = bwmon_remove,
+ .driver = {
+ .name = "qcom-bwmon",
+ .of_match_table = bwmon_of_match,
+ },
+};
+module_platform_driver(bwmon_driver);
+
+MODULE_AUTHOR("Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>")
+MODULE_DESCRIPTION("QCOM BWMON driver");
+MODULE_LICENSE("GPL");
--
2.32.0
