From: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx> Convert txt binding to yaml binding for Mediatek switches. Signed-off-by: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx> --- .../devicetree/bindings/net/dsa/mediatek.yaml | 435 ++++++++++++++++++ .../devicetree/bindings/net/dsa/mt7530.txt | 327 ------------- 2 files changed, 435 insertions(+), 327 deletions(-) create mode 100644 Documentation/devicetree/bindings/net/dsa/mediatek.yaml delete mode 100644 Documentation/devicetree/bindings/net/dsa/mt7530.txt diff --git a/Documentation/devicetree/bindings/net/dsa/mediatek.yaml b/Documentation/devicetree/bindings/net/dsa/mediatek.yaml new file mode 100644 index 000000000000..c1724809d34e --- /dev/null +++ b/Documentation/devicetree/bindings/net/dsa/mediatek.yaml @@ -0,0 +1,435 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/dsa/mediatek.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Mediatek MT7530 Ethernet switch + +maintainers: + - Sean Wang <sean.wang@xxxxxxxxxxxx> + - Landen Chao <Landen.Chao@xxxxxxxxxxxx> + - DENG Qingfang <dqfext@xxxxxxxxx> + +description: | + Port 5 of mt7530 and mt7621 switch is muxed between: + 1. GMAC5: GMAC5 can interface with another external MAC or PHY. + 2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC + of the SOC. Used in many setups where port 0/4 becomes the WAN port. + Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to + GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not + connected to external component! + + Port 5 modes/configurations: + 1. Port 5 is disabled and isolated: An external phy can interface to the 2nd + GMAC of the SOC. + In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd + GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC! + 2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC. + It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode + and RGMII delay. + 3. Port 5 is muxed to GMAC5 and can interface to an external phy. + Port 5 becomes an extra switch port. + Only works on platform where external phy TX<->RX lines are swapped. + Like in the Ubiquiti ER-X-SFP. + 4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port. + Currently a 2nd CPU port is not supported by DSA code. + + Depending on how the external PHY is wired: + 1. normal: The PHY can only connect to 2nd GMAC but not to the switch + 2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as + a ethernet port. But can't interface to the 2nd GMAC. + + Based on the DT the port 5 mode is configured. + + Driver tries to lookup the phy-handle of the 2nd GMAC of the master device. + When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2. + phy-mode must be set, see also example 2 below! + * mt7621: phy-mode = "rgmii-txid"; + * mt7623: phy-mode = "rgmii"; + + CPU-Ports need a phy-mode property: + Allowed values on mt7530 and mt7621: + - "rgmii" + - "trgmii" + On mt7531: + - "1000base-x" + - "2500base-x" + - "sgmii" + + +properties: + compatible: + enum: + - mediatek,mt7530 + - mediatek,mt7531 + - mediatek,mt7621 + + "#address-cells": + const: 1 + + "#size-cells": + const: 0 + + core-supply: + description: | + Phandle to the regulator node necessary for the core power. + + "#gpio-cells": + description: | + Must be 2 if gpio-controller is defined. + const: 2 + + gpio-controller: + type: boolean + description: | + Boolean; if defined, MT7530's LED controller will run on + GPIO mode. + + "#interrupt-cells": + const: 1 + + interrupt-controller: + type: boolean + description: | + Boolean; Enables the internal interrupt controller. + + interrupts: + description: | + Parent interrupt for the interrupt controller. + maxItems: 1 + + io-supply: + description: | + Phandle to the regulator node necessary for the I/O power. + See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt + for details for the regulator setup on these boards. + + mediatek,mcm: + type: boolean + description: | + Boolean; if defined, indicates that either MT7530 is the part + on multi-chip module belong to MT7623A has or the remotely standalone + chip as the function MT7623N reference board provided for. + + reset-gpios: + description: | + Should be a gpio specifier for a reset line. + maxItems: 1 + + reset-names: + description: | + Should be set to "mcm". + const: mcm + + resets: + description: | + Phandle pointing to the system reset controller with + line index for the ethsys. + maxItems: 1 + +required: + - compatible + - reg + +allOf: + - $ref: "dsa.yaml#" + - if: + required: + - mediatek,mcm + then: + required: + - resets + - reset-names + else: + required: + - reset-gpios + + - if: + required: + - interrupt-controller + then: + required: + - "#interrupt-cells" + - interrupts + + - if: + properties: + compatible: + items: + - const: mediatek,mt7530 + then: + required: + - core-supply + - io-supply + + +patternProperties: + "^ports$": + type: object + + patternProperties: + "^port@[0-9]+$": + type: object + description: Ethernet switch ports + + $ref: dsa-port.yaml# + + properties: + reg: + description: | + Port address described must be 6 for CPU port and from 0 to 5 for user ports. + + unevaluatedProperties: false + + allOf: + - if: + properties: + label: + items: + - const: cpu + then: + required: + - reg + - phy-mode + +unevaluatedProperties: false + +examples: + - | + mdio0 { + #address-cells = <1>; + #size-cells = <0>; + switch@0 { + compatible = "mediatek,mt7530"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + + core-supply = <&mt6323_vpa_reg>; + io-supply = <&mt6323_vemc3v3_reg>; + reset-gpios = <&pio 33 0>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "wan"; + }; + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "trgmii"; + fixed-link { + speed = <1000>; + full-duplex; + }; + }; + }; + }; + }; + + - | + //Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4. + + eth { + #address-cells = <1>; + #size-cells = <0>; + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "rgmii-txid"; + phy-handle = <&phy4>; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + /* Internal phy */ + phy4: ethernet-phy@4 { + reg = <4>; + }; + + mt7530: switch@1f { + compatible = "mediatek,mt7621"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1f>; + mediatek,mcm; + + resets = <&rstctrl 2>; + reset-names = "mcm"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + /* Commented out. Port 4 is handled by 2nd GMAC. + port@4 { + reg = <4>; + label = "lan4"; + }; + */ + + port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + }; + + - | + //Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY. + + eth { + #address-cells = <1>; + #size-cells = <0>; + gmac_0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + + mdio0: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + + /* External phy */ + ephy5: ethernet-phy@7 { + reg = <7>; + }; + + switch@1f { + compatible = "mediatek,mt7621"; + #address-cells = <1>; + #size-cells = <0>; + reg = <0x1f>; + mediatek,mcm; + + resets = <&rstctrl 2>; + reset-names = "mcm"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + label = "lan0"; + }; + + port@1 { + reg = <1>; + label = "lan1"; + }; + + port@2 { + reg = <2>; + label = "lan2"; + }; + + port@3 { + reg = <3>; + label = "lan3"; + }; + + port@4 { + reg = <4>; + label = "lan4"; + }; + + port@5 { + reg = <5>; + label = "lan5"; + phy-mode = "rgmii"; + phy-handle = <&ephy5>; + }; + + cpu_port0: port@6 { + reg = <6>; + label = "cpu"; + ethernet = <&gmac_0>; + phy-mode = "rgmii"; + + fixed-link { + speed = <1000>; + full-duplex; + pause; + }; + }; + }; + }; + }; + }; diff --git a/Documentation/devicetree/bindings/net/dsa/mt7530.txt b/Documentation/devicetree/bindings/net/dsa/mt7530.txt deleted file mode 100644 index 18247ebfc487..000000000000 --- a/Documentation/devicetree/bindings/net/dsa/mt7530.txt +++ /dev/null @@ -1,327 +0,0 @@ -Mediatek MT7530 Ethernet switch -================================ - -Required properties: - -- compatible: may be compatible = "mediatek,mt7530" - or compatible = "mediatek,mt7621" - or compatible = "mediatek,mt7531" -- #address-cells: Must be 1. -- #size-cells: Must be 0. -- mediatek,mcm: Boolean; if defined, indicates that either MT7530 is the part - on multi-chip module belong to MT7623A has or the remotely standalone - chip as the function MT7623N reference board provided for. - -If compatible mediatek,mt7530 is set then the following properties are required - -- core-supply: Phandle to the regulator node necessary for the core power. -- io-supply: Phandle to the regulator node necessary for the I/O power. - See Documentation/devicetree/bindings/regulator/mt6323-regulator.txt - for details for the regulator setup on these boards. - -If the property mediatek,mcm isn't defined, following property is required - -- reset-gpios: Should be a gpio specifier for a reset line. - -Else, following properties are required - -- resets : Phandle pointing to the system reset controller with - line index for the ethsys. -- reset-names : Should be set to "mcm". - -Required properties for the child nodes within ports container: - -- reg: Port address described must be 6 for CPU port and from 0 to 5 for - user ports. -- phy-mode: String, the following values are acceptable for port labeled - "cpu": - If compatible mediatek,mt7530 or mediatek,mt7621 is set, - must be either "trgmii" or "rgmii" - If compatible mediatek,mt7531 is set, - must be either "sgmii", "1000base-x" or "2500base-x" - -Port 5 of mt7530 and mt7621 switch is muxed between: -1. GMAC5: GMAC5 can interface with another external MAC or PHY. -2. PHY of port 0 or port 4: PHY interfaces with an external MAC like 2nd GMAC - of the SOC. Used in many setups where port 0/4 becomes the WAN port. - Note: On a MT7621 SOC with integrated switch: 2nd GMAC can only connected to - GMAC5 when the gpios for RGMII2 (GPIO 22-33) are not used and not - connected to external component! - -Port 5 modes/configurations: -1. Port 5 is disabled and isolated: An external phy can interface to the 2nd - GMAC of the SOC. - In the case of a build-in MT7530 switch, port 5 shares the RGMII bus with 2nd - GMAC and an optional external phy. Mind the GPIO/pinctl settings of the SOC! -2. Port 5 is muxed to PHY of port 0/4: Port 0/4 interfaces with 2nd GMAC. - It is a simple MAC to PHY interface, port 5 needs to be setup for xMII mode - and RGMII delay. -3. Port 5 is muxed to GMAC5 and can interface to an external phy. - Port 5 becomes an extra switch port. - Only works on platform where external phy TX<->RX lines are swapped. - Like in the Ubiquiti ER-X-SFP. -4. Port 5 is muxed to GMAC5 and interfaces with the 2nd GAMC as 2nd CPU port. - Currently a 2nd CPU port is not supported by DSA code. - -Depending on how the external PHY is wired: -1. normal: The PHY can only connect to 2nd GMAC but not to the switch -2. swapped: RGMII TX, RX are swapped; external phy interface with the switch as - a ethernet port. But can't interface to the 2nd GMAC. - -Based on the DT the port 5 mode is configured. - -Driver tries to lookup the phy-handle of the 2nd GMAC of the master device. -When phy-handle matches PHY of port 0 or 4 then port 5 set-up as mode 2. -phy-mode must be set, see also example 2 below! - * mt7621: phy-mode = "rgmii-txid"; - * mt7623: phy-mode = "rgmii"; - -Optional properties: - -- gpio-controller: Boolean; if defined, MT7530's LED controller will run on - GPIO mode. -- #gpio-cells: Must be 2 if gpio-controller is defined. -- interrupt-controller: Boolean; Enables the internal interrupt controller. - -If interrupt-controller is defined, the following properties are required. - -- #interrupt-cells: Must be 1. -- interrupts: Parent interrupt for the interrupt controller. - -See Documentation/devicetree/bindings/net/dsa/dsa.txt for a list of additional -required, optional properties and how the integrated switch subnodes must -be specified. - -Example: - - &mdio0 { - switch@0 { - compatible = "mediatek,mt7530"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - - core-supply = <&mt6323_vpa_reg>; - io-supply = <&mt6323_vemc3v3_reg>; - reset-gpios = <&pio 33 0>; - - ports { - #address-cells = <1>; - #size-cells = <0>; - reg = <0>; - port@0 { - reg = <0>; - label = "lan0"; - }; - - port@1 { - reg = <1>; - label = "lan1"; - }; - - port@2 { - reg = <2>; - label = "lan2"; - }; - - port@3 { - reg = <3>; - label = "lan3"; - }; - - port@4 { - reg = <4>; - label = "wan"; - }; - - port@6 { - reg = <6>; - label = "cpu"; - ethernet = <&gmac0>; - phy-mode = "trgmii"; - fixed-link { - speed = <1000>; - full-duplex; - }; - }; - }; - }; - }; - -Example 2: MT7621: Port 4 is WAN port: 2nd GMAC -> Port 5 -> PHY port 4. - -ð { - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "rgmii"; - - fixed-link { - speed = <1000>; - full-duplex; - pause; - }; - }; - - gmac1: mac@1 { - compatible = "mediatek,eth-mac"; - reg = <1>; - phy-mode = "rgmii-txid"; - phy-handle = <&phy4>; - }; - - mdio: mdio-bus { - #address-cells = <1>; - #size-cells = <0>; - - /* Internal phy */ - phy4: ethernet-phy@4 { - reg = <4>; - }; - - mt7530: switch@1f { - compatible = "mediatek,mt7621"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x1f>; - pinctrl-names = "default"; - mediatek,mcm; - - resets = <&rstctrl 2>; - reset-names = "mcm"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "lan0"; - }; - - port@1 { - reg = <1>; - label = "lan1"; - }; - - port@2 { - reg = <2>; - label = "lan2"; - }; - - port@3 { - reg = <3>; - label = "lan3"; - }; - -/* Commented out. Port 4 is handled by 2nd GMAC. - port@4 { - reg = <4>; - label = "lan4"; - }; -*/ - - cpu_port0: port@6 { - reg = <6>; - label = "cpu"; - ethernet = <&gmac0>; - phy-mode = "rgmii"; - - fixed-link { - speed = <1000>; - full-duplex; - pause; - }; - }; - }; - }; - }; -}; - -Example 3: MT7621: Port 5 is connected to external PHY: Port 5 -> external PHY. - -ð { - gmac0: mac@0 { - compatible = "mediatek,eth-mac"; - reg = <0>; - phy-mode = "rgmii"; - - fixed-link { - speed = <1000>; - full-duplex; - pause; - }; - }; - - mdio: mdio-bus { - #address-cells = <1>; - #size-cells = <0>; - - /* External phy */ - ephy5: ethernet-phy@7 { - reg = <7>; - }; - - mt7530: switch@1f { - compatible = "mediatek,mt7621"; - #address-cells = <1>; - #size-cells = <0>; - reg = <0x1f>; - pinctrl-names = "default"; - mediatek,mcm; - - resets = <&rstctrl 2>; - reset-names = "mcm"; - - ports { - #address-cells = <1>; - #size-cells = <0>; - - port@0 { - reg = <0>; - label = "lan0"; - }; - - port@1 { - reg = <1>; - label = "lan1"; - }; - - port@2 { - reg = <2>; - label = "lan2"; - }; - - port@3 { - reg = <3>; - label = "lan3"; - }; - - port@4 { - reg = <4>; - label = "lan4"; - }; - - port@5 { - reg = <5>; - label = "lan5"; - phy-mode = "rgmii"; - phy-handle = <&ephy5>; - }; - - cpu_port0: port@6 { - reg = <6>; - label = "cpu"; - ethernet = <&gmac0>; - phy-mode = "rgmii"; - - fixed-link { - speed = <1000>; - full-duplex; - pause; - }; - }; - }; - }; - }; -}; -- 2.25.1
