While the Pro-1 is based on MTP and is very close to it, it's really not great
for it to include the MTP dtsi straight up, as any small change will affect
both boards and not all of them will apply to the phone as well.
Signed-off-by: Konrad Dybcio <konrad.dybcio@xxxxxxxxxxxxxx>
---
.../boot/dts/qcom/msm8998-fxtec-pro1.dts | 421 +++++++++++++++++-
1 file changed, 420 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts b/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts
index f61ea651b0eb..adbb933f4cd1 100644
--- a/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts
+++ b/arch/arm64/boot/dts/qcom/msm8998-fxtec-pro1.dts
@@ -9,7 +9,10 @@
#include <dt-bindings/input/input.h>
#include <dt-bindings/leds/common.h>
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
-#include "msm8998-mtp.dtsi"
+#include "msm8998.dtsi"
+#include "pm8005.dtsi"
+#include "pm8998.dtsi"
+#include "pmi8998.dtsi"
/ {
model = "F(x)tec Pro1 (QX1000)";
@@ -17,6 +20,11 @@ / {
chassis-type = "handset";
qcom,board-id = <0x02000b 0x10>;
+ aliases {
+ serial0 = &blsp2_uart1;
+ serial1 = &blsp1_uart3;
+ };
+
/*
* Until we hook up type-c detection, we
* have to stick with this. But it works.
@@ -186,6 +194,53 @@ ts_vio_vreg: ts-vio-vreg {
pinctrl-0 = <&ts_vio_default>;
regulator-always-on;
};
+
+ vph_pwr: vph-pwr-regulator {
+ compatible = "regulator-fixed";
+ regulator-name = "vph_pwr";
+ regulator-always-on;
+ regulator-boot-on;
+ };
+};
+
+&blsp1_uart3 {
+ status = "okay";
+
+ bluetooth {
+ compatible = "qcom,wcn3990-bt";
+
+ vddio-supply = <&vreg_s4a_1p8>;
+ vddxo-supply = <&vreg_l7a_1p8>;
+ vddrf-supply = <&vreg_l17a_1p3>;
+ vddch0-supply = <&vreg_l25a_3p3>;
+ max-speed = <3200000>;
+ };
+};
+
+&blsp1_uart3_on {
+ rx {
+ /delete-property/ bias-disable;
+ /*
+ * Configure a pull-up on 45 (RX). This is needed to
+ * avoid garbage data when the TX pin of the Bluetooth
+ * module is in tri-state (module powered off or not
+ * driving the signal yet).
+ */
+ bias-pull-up;
+ };
+
+ cts {
+ /delete-property/ bias-disable;
+ /*
+ * Configure a pull-down on 47 (CTS) to match the pull
+ * of the Bluetooth module.
+ */
+ bias-pull-down;
+ };
+};
+
+&blsp2_uart1 {
+ status = "okay";
};
&blsp2_i2c1 {
@@ -204,6 +259,91 @@ touchscreen@14 {
};
};
+&etf {
+ status = "okay";
+};
+
+&etm1 {
+ status = "okay";
+};
+
+&etm2 {
+ status = "okay";
+};
+
+&etm3 {
+ status = "okay";
+};
+
+&etm4 {
+ status = "okay";
+};
+
+&etm5 {
+ status = "okay";
+};
+
+&etm6 {
+ status = "okay";
+};
+
+&etm7 {
+ status = "okay";
+};
+
+&etm8 {
+ status = "okay";
+};
+
+&etr {
+ status = "okay";
+};
+
+&funnel1 {
+ status = "okay";
+};
+
+&funnel2 {
+ status = "okay";
+};
+
+&funnel3 {
+ status = "okay";
+};
+
+&funnel4 {
+ // FIXME: Figure out why clock late_initcall crashes the board with
+ // this enabled.
+ // status = "okay";
+};
+
+&funnel5 {
+ // FIXME: Figure out why clock late_initcall crashes the board with
+ // this enabled.
+ // status = "okay";
+};
+
+&pcie0 {
+ status = "okay";
+};
+
+&pcie_phy {
+ status = "okay";
+};
+
+&pm8005_regulators {
+ vdd_s1-supply = <&vph_pwr>;
+
+ pm8005_s1: s1 { /* VDD_GFX supply */
+ regulator-min-microvolt = <524000>;
+ regulator-max-microvolt = <1100000>;
+ regulator-enable-ramp-delay = <500>;
+
+ /* Hack until we rig up the gpu consumer */
+ regulator-always-on;
+ };
+};
+
&pm8998_gpio {
vol_up_pin_a: vol-up-active {
pins = "gpio6";
@@ -240,6 +380,240 @@ resin {
};
};
+&qusb2phy {
+ status = "okay";
+
+ vdda-pll-supply = <&vreg_l12a_1p8>;
+ vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
+};
+
+&replicator1 {
+ status = "okay";
+};
+
+&rpm_requests {
+ pm8998-regulators {
+ compatible = "qcom,rpm-pm8998-regulators";
+
+ vdd_s1-supply = <&vph_pwr>;
+ vdd_s2-supply = <&vph_pwr>;
+ vdd_s3-supply = <&vph_pwr>;
+ vdd_s4-supply = <&vph_pwr>;
+ vdd_s5-supply = <&vph_pwr>;
+ vdd_s6-supply = <&vph_pwr>;
+ vdd_s7-supply = <&vph_pwr>;
+ vdd_s8-supply = <&vph_pwr>;
+ vdd_s9-supply = <&vph_pwr>;
+ vdd_s10-supply = <&vph_pwr>;
+ vdd_s11-supply = <&vph_pwr>;
+ vdd_s12-supply = <&vph_pwr>;
+ vdd_s13-supply = <&vph_pwr>;
+ vdd_l1_l27-supply = <&vreg_s7a_1p025>;
+ vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
+ vdd_l3_l11-supply = <&vreg_s7a_1p025>;
+ vdd_l4_l5-supply = <&vreg_s7a_1p025>;
+ vdd_l6-supply = <&vreg_s5a_2p04>;
+ vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
+ vdd_l9-supply = <&vreg_bob>;
+ vdd_l10_l23_l25-supply = <&vreg_bob>;
+ vdd_l13_l19_l21-supply = <&vreg_bob>;
+ vdd_l16_l28-supply = <&vreg_bob>;
+ vdd_l18_l22-supply = <&vreg_bob>;
+ vdd_l20_l24-supply = <&vreg_bob>;
+ vdd_l26-supply = <&vreg_s3a_1p35>;
+ vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
+
+ vreg_s3a_1p35: s3 {
+ regulator-min-microvolt = <1352000>;
+ regulator-max-microvolt = <1352000>;
+ };
+
+ vreg_s4a_1p8: s4 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-allow-set-load;
+ };
+
+ vreg_s5a_2p04: s5 {
+ regulator-min-microvolt = <1904000>;
+ regulator-max-microvolt = <2040000>;
+ };
+
+ vreg_s7a_1p025: s7 {
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1028000>;
+ };
+
+ vreg_l1a_0p875: l1 {
+ regulator-min-microvolt = <880000>;
+ regulator-max-microvolt = <880000>;
+ };
+
+ vreg_l2a_1p2: l2 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vreg_l3a_1p0: l3 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ vreg_l5a_0p8: l5 {
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <800000>;
+ };
+
+ vreg_l6a_1p8: l6 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <1808000>;
+ };
+
+ vreg_l7a_1p8: l7 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_l8a_1p2: l8 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vreg_l9a_1p8: l9 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2960000>;
+ };
+
+ vreg_l10a_1p8: l10 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2960000>;
+ };
+
+ vreg_l11a_1p0: l11 {
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ vreg_l12a_1p8: l12 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_l13a_2p95: l13 {
+ regulator-min-microvolt = <1808000>;
+ regulator-max-microvolt = <2960000>;
+ };
+
+ vreg_l14a_1p88: l14 {
+ regulator-min-microvolt = <1880000>;
+ regulator-max-microvolt = <1880000>;
+ };
+
+ vreg_l15a_1p8: l15 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_l16a_2p7: l16 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+ };
+
+ vreg_l17a_1p3: l17 {
+ regulator-min-microvolt = <1304000>;
+ regulator-max-microvolt = <1304000>;
+ };
+
+ vreg_l18a_2p7: l18 {
+ regulator-min-microvolt = <2704000>;
+ regulator-max-microvolt = <2704000>;
+ };
+
+ vreg_l19a_3p0: l19 {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ };
+
+ vreg_l20a_2p95: l20 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l21a_2p95: l21 {
+ regulator-min-microvolt = <2960000>;
+ regulator-max-microvolt = <2960000>;
+ regulator-system-load = <800000>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l22a_2p85: l22 {
+ regulator-min-microvolt = <2864000>;
+ regulator-max-microvolt = <2864000>;
+ };
+
+ vreg_l23a_3p3: l23 {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3312000>;
+ };
+
+ vreg_l24a_3p075: l24 {
+ regulator-min-microvolt = <3088000>;
+ regulator-max-microvolt = <3088000>;
+ };
+
+ vreg_l25a_3p3: l25 {
+ regulator-min-microvolt = <3104000>;
+ regulator-max-microvolt = <3312000>;
+ };
+
+ vreg_l26a_1p2: l26 {
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-allow-set-load;
+ };
+
+ vreg_l28_3p0: l28 {
+ regulator-min-microvolt = <3008000>;
+ regulator-max-microvolt = <3008000>;
+ };
+
+ vreg_lvs1a_1p8: lvs1 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vreg_lvs2a_1p8: lvs2 {
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ };
+
+ pmi8998-regulators {
+ compatible = "qcom,rpm-pmi8998-regulators";
+
+ vdd_bob-supply = <&vph_pwr>;
+
+ vreg_bob: bob {
+ regulator-min-microvolt = <3312000>;
+ regulator-max-microvolt = <3600000>;
+ };
+ };
+};
+
+&remoteproc_adsp {
+ status = "okay";
+};
+
+&remoteproc_mss {
+ status = "okay";
+};
+
+&remoteproc_slpi {
+ status = "okay";
+};
+
&tlmm {
gpio-reserved-ranges = <0 4>;
@@ -288,12 +662,41 @@ ts_int_n: ts-int-n {
};
};
+&sdhc2 {
+ status = "okay";
+ cd-gpios = <&tlmm 95 GPIO_ACTIVE_LOW>;
+
+ vmmc-supply = <&vreg_l21a_2p95>;
+ vqmmc-supply = <&vreg_l13a_2p95>;
+
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&sdc2_on &sdc2_cd>;
+ pinctrl-1 = <&sdc2_off &sdc2_cd>;
+};
+
+&stm {
+ status = "okay";
+};
+
&ufshc {
status = "okay";
+ vcc-supply = <&vreg_l20a_2p95>;
+ vccq-supply = <&vreg_l26a_1p2>;
+ vccq2-supply = <&vreg_s4a_1p8>;
+ vcc-max-microamp = <750000>;
+ vccq-max-microamp = <560000>;
+ vccq2-max-microamp = <750000>;
};
&ufsphy {
status = "okay";
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l2a_1p2>;
+ vddp-ref-clk-supply = <&vreg_l26a_1p2>;
+};
+
+&usb3 {
+ status = "okay";
};
&usb3_dwc3 {
@@ -301,8 +704,24 @@ &usb3_dwc3 {
extcon = <&extcon_usb>;
};
+&usb3phy {
+ status = "okay";
+
+ vdda-phy-supply = <&vreg_l1a_0p875>;
+ vdda-pll-supply = <&vreg_l2a_1p2>;
+};
+
/* GT9286 analog supply */
&vreg_l28_3p0 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
};
+
+&wifi {
+ status = "okay";
+
+ vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
+ vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
+ vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
+ vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
+};
--
2.35.2
