Kalle Valo <kvalo@xxxxxxxxxx> writes: > Manikanta Pubbisetty <quic_mpubbise@xxxxxxxxxxx> writes: > >> WCN6750 is non-DBS 2x2 11AX chipset. Unlike QCA6390/WCN6855 which >> are DBS (dual band simultaneous) solutions (2 LMACs), WCN6750 has a >> single LMAC supporting 2G, 5G and 6G bands. It can be operated only >> on one band at any given point. >> >> WCN6750 is a PCIe device. Unlike other supported ATH11K PCIe devices >> which are directly attached to APSS (Application Processor SubSystem), >> WCN6750 is not attached to APSS, it is attached to the WPSS >> (Wireless Processor SubSystem) Q6 processor, the FW which runs on the >> Q6 processor will enumerate the PCIe device. Since APSS is unaware of >> such a device, it has to be registered as a platform device(AHB) to the >> kernel for device probing. Like other AHB devices, remoteproc APIs are >> used to boot up or shutdown of WCN6750. >> >> WCN6750 uses both AHB and PCIe ATH11K APIs for it's operation. >> It uses AHB APIs for device probe and booting of the remote processor. >> Once device is booted up, it uses ATH11K PCIe APIs for initialization >> and register access. Hence, it is referred as hybrid bus device in >> the rest of this series. >> >> Since the chip is enumerated by WPSS Q6, device information like >> BAR and BAR size is not known to the APSS processor. A new QMI message >> called device info QMI request will be sent to the target for fetching >> these details. >> >> STA and AP modes are supported; Basic connectivity and ping are >> verified in both the modes. >> >> An important point to note is that though WCN6750 is a PCIe device, >> it cannot be attached to any other platform except on Qualcomm >> Snapdragon SoCs due to the aforementioned reasons. >> >> Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1 >> Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1 >> Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 >> Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1 >> >> Manikanta Pubbisetty (12): >> dt: bindings: net: add bindings of WCN6750 for ath11k >> ath11k: Add HW params for WCN6750 >> ath11k: Add bus params for WCN6750 >> ath11k: Add register access logic for WCN6750 >> ath11k: Fetch device information via QMI for WCN6750 >> ath11k: Add QMI changes for WCN6750 >> ath11k: HAL changes to support WCN6750 >> ath11k: Datapath changes to support WCN6750 >> ath11k: Do not put HW in DBS mode for WCN6750 >> ath11k: WMI changes to support WCN6750 >> ath11k: Update WBM idle ring HP after FW mode on >> ath11k: Add support for WCN6750 device >> --- >> V5: >> - Rebased on ToT SHAID: 01be26cde012478db958d9bde530877c46031e76 > > I already had v4 applied to the pending branch so I'm going to drop v5 > and look at v4 instead. I see that you also added Rob's reviewed-by to patch 1. Please include ALL changes in the changes list, otherwise review is difficult as we don't know what you changed. -- https://patchwork.kernel.org/project/linux-wireless/list/ https://wireless.wiki.kernel.org/en/developers/documentation/submittingpatches
