On 4/26/22 06:49, Frank Wunderlich wrote:
From: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>
Currently CPU-Port is hardcoded to Port 6.
On BPI-R2-Pro board this port is not connected and only Port 5 is
connected to gmac of SoC.
Replace this hardcoded CPU-Port with a member in mt7530_priv struct
which is set in mt753x_cpu_port_enable to the right port.
I defined a default in probe (in case no CPU-Port will be setup) and
if both cpu-port were setup port 6 will be used like the const prior
this patch.
In mt7531_setup first access is before we know which port should be used
(mt753x_cpu_port_enable) so section "BPDU to CPU port" needs to be moved
down.
Signed-off-by: Frank Wunderlich <frank-w@xxxxxxxxxxxxxxx>
---
drivers/net/dsa/mt7530.c | 46 ++++++++++++++++++++++------------------
drivers/net/dsa/mt7530.h | 2 +-
2 files changed, 26 insertions(+), 22 deletions(-)
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c
index ccf4cb944167..4789105b8137 100644
--- a/drivers/net/dsa/mt7530.c
+++ b/drivers/net/dsa/mt7530.c
@@ -1004,6 +1004,7 @@ mt753x_cpu_port_enable(struct dsa_switch *ds, int port)
return ret;
}
+ priv->cpu_port = port;
/* Enable Mediatek header mode on the cpu port */
mt7530_write(priv, MT7530_PVC_P(port),
PORT_SPEC_TAG);
@@ -1041,7 +1042,7 @@ mt7530_port_enable(struct dsa_switch *ds, int port,
* restore the port matrix if the port is the member of a certain
* bridge.
*/
- priv->ports[port].pm |= PCR_MATRIX(BIT(MT7530_CPU_PORT));
+ priv->ports[port].pm |= PCR_MATRIX(BIT(priv->cpu_port));
priv->ports[port].enable = true;
mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
priv->ports[port].pm);
@@ -1190,8 +1191,8 @@ mt7530_port_bridge_join(struct dsa_switch *ds, int port,
struct netlink_ext_ack *extack)
{
struct dsa_port *dp = dsa_to_port(ds, port), *other_dp;
- u32 port_bitmap = BIT(MT7530_CPU_PORT);
struct mt7530_priv *priv = ds->priv;
+ u32 port_bitmap = BIT(priv->cpu_port);
No need to re-order these two lines.
mutex_lock(&priv->reg_mutex);
@@ -1267,9 +1268,9 @@ mt7530_port_set_vlan_unaware(struct dsa_switch *ds, int port)
* the CPU port get out of VLAN filtering mode.
*/
if (all_user_ports_removed) {
- mt7530_write(priv, MT7530_PCR_P(MT7530_CPU_PORT),
+ mt7530_write(priv, MT7530_PCR_P(priv->cpu_port),
PCR_MATRIX(dsa_user_ports(priv->ds)));
- mt7530_write(priv, MT7530_PVC_P(MT7530_CPU_PORT), PORT_SPEC_TAG
+ mt7530_write(priv, MT7530_PVC_P(priv->cpu_port), PORT_SPEC_TAG
| PVC_EG_TAG(MT7530_VLAN_EG_CONSISTENT));
}
}
@@ -1335,8 +1336,8 @@ mt7530_port_bridge_leave(struct dsa_switch *ds, int port,
*/
if (priv->ports[port].enable)
mt7530_rmw(priv, MT7530_PCR_P(port), PCR_MATRIX_MASK,
- PCR_MATRIX(BIT(MT7530_CPU_PORT)));
- priv->ports[port].pm = PCR_MATRIX(BIT(MT7530_CPU_PORT));
+ PCR_MATRIX(BIT(priv->cpu_port)));
+ priv->ports[port].pm = PCR_MATRIX(BIT(priv->cpu_port));
/* When a port is removed from the bridge, the port would be set up
* back to the default as is at initial boot which is a VLAN-unaware
@@ -1503,6 +1504,7 @@ static int
mt7530_port_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering,
struct netlink_ext_ack *extack)
{
+ struct mt7530_priv *priv = ds->priv;
Add a space to separate declaration from code.
if (vlan_filtering) {
/* The port is being kept as VLAN-unaware port when bridge is
* set up with vlan_filtering not being set, Otherwise, the
@@ -1510,7 +1512,7 @@ mt7530_port_vlan_filtering(struct dsa_switch *ds, int port, bool vlan_filtering,
* for becoming a VLAN-aware port.
*/
mt7530_port_set_vlan_aware(ds, port);
- mt7530_port_set_vlan_aware(ds, MT7530_CPU_PORT);
+ mt7530_port_set_vlan_aware(ds, priv->cpu_port);
} else {
mt7530_port_set_vlan_unaware(ds, port);
}
@@ -1526,7 +1528,7 @@ mt7530_hw_vlan_add(struct mt7530_priv *priv,
u32 val;
new_members = entry->old_members | BIT(entry->port) |
- BIT(MT7530_CPU_PORT);
+ BIT(priv->cpu_port);
/* Validate the entry with independent learning, create egress tag per
* VLAN and joining the port as one of the port members.
@@ -1550,8 +1552,8 @@ mt7530_hw_vlan_add(struct mt7530_priv *priv,
* DSA tag.
*/
mt7530_rmw(priv, MT7530_VAWD2,
- ETAG_CTRL_P_MASK(MT7530_CPU_PORT),
- ETAG_CTRL_P(MT7530_CPU_PORT,
+ ETAG_CTRL_P_MASK(priv->cpu_port),
+ ETAG_CTRL_P(priv->cpu_port,
MT7530_VLAN_EGRESS_STACK));
}
@@ -1575,7 +1577,7 @@ mt7530_hw_vlan_del(struct mt7530_priv *priv,
* the entry would be kept valid. Otherwise, the entry is got to be
* disabled.
*/
- if (new_members && new_members != BIT(MT7530_CPU_PORT)) {
+ if (new_members && new_members != BIT(priv->cpu_port)) {
val = IVL_MAC | VTAG_EN | PORT_MEM(new_members) |
VLAN_VALID;
mt7530_write(priv, MT7530_VAWD1, val);
@@ -2105,7 +2107,7 @@ mt7530_setup(struct dsa_switch *ds)
* controller also is the container for two GMACs nodes representing
* as two netdev instances.
*/
- dn = dsa_to_port(ds, MT7530_CPU_PORT)->master->dev.of_node->parent;
+ dn = dsa_to_port(ds, priv->cpu_port)->master->dev.of_node->parent;
ds->assisted_learning_on_cpu_port = true;
ds->mtu_enforcement_ingress = true;
@@ -2337,15 +2339,6 @@ mt7531_setup(struct dsa_switch *ds)
mt7531_ind_c45_phy_write(priv, MT753X_CTRL_PHY_ADDR, MDIO_MMD_VEND2,
CORE_PLL_GROUP4, val);
- /* BPDU to CPU port */
- mt7530_rmw(priv, MT7531_CFC, MT7531_CPU_PMAP_MASK,
- BIT(MT7530_CPU_PORT));
- mt7530_rmw(priv, MT753X_BPC, MT753X_BPDU_PORT_FW_MASK,
- MT753X_BPDU_CPU_ONLY);
-
- /* Enable and reset MIB counters */
- mt7530_mib_reset(ds);
-
for (i = 0; i < MT7530_NUM_PORTS; i++) {
/* Disable forwarding by default on all ports */
mt7530_rmw(priv, MT7530_PCR_P(i), PCR_MATRIX_MASK,
@@ -2373,6 +2366,15 @@ mt7531_setup(struct dsa_switch *ds)
PVC_EG_TAG(MT7530_VLAN_EG_CONSISTENT));
}
+ /* BPDU to CPU port */
+ mt7530_rmw(priv, MT7531_CFC, MT7531_CPU_PMAP_MASK,
+ BIT(priv->cpu_port));
+ mt7530_rmw(priv, MT753X_BPC, MT753X_BPDU_PORT_FW_MASK,
+ MT753X_BPDU_CPU_ONLY);
+
+ /* Enable and reset MIB counters */
+ mt7530_mib_reset(ds);
+
/* Setup VLAN ID 0 for VLAN-unaware bridges */
ret = mt7530_setup_vlan0(priv);
if (ret)
@@ -3213,6 +3215,8 @@ mt7530_probe(struct mdio_device *mdiodev)
if (!priv)
return -ENOMEM;
+ priv->cpu_port = 6;
+
priv->ds = devm_kzalloc(&mdiodev->dev, sizeof(*priv->ds), GFP_KERNEL);
if (!priv->ds)
return -ENOMEM;
diff --git a/drivers/net/dsa/mt7530.h b/drivers/net/dsa/mt7530.h
index 91508e2feef9..62df8d10f6d4 100644
--- a/drivers/net/dsa/mt7530.h
+++ b/drivers/net/dsa/mt7530.h
@@ -8,7 +8,6 @@
#define MT7530_NUM_PORTS 7
#define MT7530_NUM_PHYS 5
-#define MT7530_CPU_PORT 6
We could have kept this define and rename it MT7530_DEFAULT_CPU_PORT or
something and in m7530_probe() use that newly renamed constant to
illustrate that we have a default value assigned, just in case.
#define MT7530_NUM_FDB_RECORDS 2048
#define MT7530_ALL_MEMBERS 0xff
@@ -823,6 +822,7 @@ struct mt7530_priv {
u8 mirror_tx;
struct mt7530_port ports[MT7530_NUM_PORTS];
+ int cpu_port;
This can be an unsigned integer since you do not assign negative values.
With that fixes, this looks good to me.
--
Florian
