Add a node for the adsp found on msm8226.
Signed-off-by: Luca Weiss <luca@xxxxxxxxx>
---
.../boot/dts/qcom-apq8026-asus-sparrow.dts | 2 +
arch/arm/boot/dts/qcom-msm8226.dtsi | 65 +++++++++++++++++++
2 files changed, 67 insertions(+)
diff --git a/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts b/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
index ace8cea27949..818c1a201227 100644
--- a/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
+++ b/arch/arm/boot/dts/qcom-apq8026-asus-sparrow.dts
@@ -8,6 +8,8 @@
#include "qcom-msm8226.dtsi"
#include "qcom-pm8226.dtsi"
+/delete-node/ &adsp_region;
+
/ {
model = "ASUS ZenWatch 2";
compatible = "asus,sparrow", "qcom,apq8026";
diff --git a/arch/arm/boot/dts/qcom-msm8226.dtsi b/arch/arm/boot/dts/qcom-msm8226.dtsi
index 28eca15b5712..3016035d5e21 100644
--- a/arch/arm/boot/dts/qcom-msm8226.dtsi
+++ b/arch/arm/boot/dts/qcom-msm8226.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/interrupt-controller/arm-gic.h>
#include <dt-bindings/clock/qcom,gcc-msm8974.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/power/qcom-rpmpd.h>
#include <dt-bindings/reset/qcom,gcc-msm8974.h>
/ {
@@ -60,6 +61,11 @@ smem_region: smem@3000000 {
reg = <0x3000000 0x100000>;
no-map;
};
+
+ adsp_region: adsp@dc00000 {
+ reg = <0x0dc00000 0x1900000>;
+ no-map;
+ };
};
smd {
@@ -115,6 +121,31 @@ smem {
hwlocks = <&tcsr_mutex 3>;
};
+ smp2p-adsp {
+ compatible = "qcom,smp2p";
+ qcom,smem = <443>, <429>;
+
+ interrupt-parent = <&intc>;
+ interrupts = <GIC_SPI 158 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,ipc = <&apcs 8 10>;
+
+ qcom,local-pid = <0>;
+ qcom,remote-pid = <2>;
+
+ adsp_smp2p_out: master-kernel {
+ qcom,entry-name = "master-kernel";
+ #qcom,smem-state-cells = <1>;
+ };
+
+ adsp_smp2p_in: slave-kernel {
+ qcom,entry-name = "slave-kernel";
+
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+ };
+
soc: soc {
compatible = "simple-bus";
#address-cells = <1>;
@@ -512,6 +543,40 @@ tcsr_mutex_block: syscon@fd484000 {
compatible = "syscon";
reg = <0xfd484000 0x2000>;
};
+
+ adsp: remoteproc@fe200000 {
+ compatible = "qcom,msm8226-adsp-pil";
+ reg = <0xfe200000 0x100>;
+
+ interrupts-extended = <&intc GIC_SPI 162 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 0 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 1 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 2 IRQ_TYPE_EDGE_RISING>,
+ <&adsp_smp2p_in 3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "wdog", "fatal", "ready", "handover", "stop-ack";
+
+ power-domains = <&rpmpd MSM8226_VDDCX>;
+ power-domain-names = "cx";
+
+ clocks = <&xo_board>;
+ clock-names = "xo";
+
+ memory-region = <&adsp_region>;
+
+ qcom,smem-states = <&adsp_smp2p_out 0>;
+ qcom,smem-state-names = "stop";
+
+ status = "disabled";
+
+ smd-edge {
+ interrupts = <GIC_SPI 156 IRQ_TYPE_EDGE_RISING>;
+
+ qcom,ipc = <&apcs 8 8>;
+ qcom,smd-edge = <1>;
+
+ label = "lpass";
+ };
+ };
};
timer {
--
2.36.0
