Hi Icenowy,
On 4/22/22 11:11 AM, icenowy@xxxxxxxxxxx wrote:
> From: Icenowy Zheng <icenowy@xxxxxxx>
>
> The thermal sensor controller on R329 is similar to the one on H6, but
> with only one sensor. Calibration method is still unknown because no
> calibration is implemented in BSP kernel, neither is it documented in
> the user manual.
Looking at the BSP smartx-r329-tina-for-jishu-community-v0.2, I see:
ths_calib: calib@14 {
reg = <0x14 4>;
};
And the BSP driver (drivers/thermal/sunxi_thermal-ng.c) claims that R329 uses
the same calibration method as for H616. Maybe you are looking at an older BSP?
Regards,
Samuel
>
> Add its support to sun8i-thermal driver. Calibrating it is now
> prevented.
>
> Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
> ---
> drivers/thermal/sun8i_thermal.c | 15 ++++++++++++++-
> 1 file changed, 14 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
> index d9cd23cbb671..3a2f381005b4 100644
> --- a/drivers/thermal/sun8i_thermal.c
> +++ b/drivers/thermal/sun8i_thermal.c
> @@ -312,7 +312,8 @@ static int sun8i_ths_calibrate(struct ths_device *tmdev)
> goto out;
> }
>
> - tmdev->chip->calibrate(tmdev, caldata, callen);
> + if (tmdev->chip->calibrate)
> + tmdev->chip->calibrate(tmdev, caldata, callen);
>
> kfree(caldata);
> out:
> @@ -628,6 +629,17 @@ static const struct ths_thermal_chip sun50i_h6_ths = {
> .calc_temp = sun8i_ths_calc_temp,
> };
>
> +static const struct ths_thermal_chip sun50i_r329_ths = {
> + .sensor_num = 1,
> + .has_bus_clk_reset = true,
> + .offset = 188744,
> + .scale = 672,
> + .temp_data_base = SUN50I_H6_THS_TEMP_DATA,
> + .init = sun50i_h6_thermal_init,
> + .irq_ack = sun50i_h6_irq_ack,
> + .calc_temp = sun8i_ths_calc_temp,
> +};
> +
> static const struct of_device_id of_ths_match[] = {
> { .compatible = "allwinner,sun8i-a83t-ths", .data = &sun8i_a83t_ths },
> { .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths },
> @@ -636,6 +648,7 @@ static const struct of_device_id of_ths_match[] = {
> { .compatible = "allwinner,sun50i-a100-ths", .data = &sun50i_a100_ths },
> { .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths },
> { .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
> + { .compatible = "allwinner,sun50i-r329-ths", .data = &sun50i_r329_ths },
> { /* sentinel */ },
> };
> MODULE_DEVICE_TABLE(of, of_ths_match);
>
