Hi,
Zhi Li wrote:
> On Mon, Sep 15, 2014 at 2:39 AM, Lothar Waßmann <LW@xxxxxxxxxxxxxxxxxxx> wrote:
> > Hi,
> >
> > Frank.Li@xxxxxxxxxxxxx wrote:
> >> From: Fugang Duan <B38611@xxxxxxxxxxxxx>
> >>
> >> By default, the tx/rx queue number is 1, user can config the queue number
> >> at DTS file like this:
> >> fsl,num-tx-queues=<3>;
> >> fsl,num-rx-queues=<3>
> >>
> >> Since i.MX6SX enet-AVB IP support multi queues, so use multi queues
> >> interface to allocate and set up an Ethernet device.
> >>
> >> Signed-off-by: Fugang Duan <B38611@xxxxxxxxxxxxx>
> >> Signed-off-by: Frank Li <Frank.Li@xxxxxxxxxxxxx>
> >> ---
> >> drivers/net/ethernet/freescale/fec.h | 2 ++
> >> drivers/net/ethernet/freescale/fec_main.c | 46 ++++++++++++++++++++++++++++++-
> >> 2 files changed, 47 insertions(+), 1 deletion(-)
> >>
> >> diff --git a/drivers/net/ethernet/freescale/fec.h b/drivers/net/ethernet/freescale/fec.h
> >> index b2b91f8..72fb90f 100644
> >> --- a/drivers/net/ethernet/freescale/fec.h
> >> +++ b/drivers/net/ethernet/freescale/fec.h
> >> @@ -356,6 +356,8 @@ struct fec_enet_private {
> >>
> >> bool ptp_clk_on;
> >> struct mutex ptp_clk_mutex;
> >> + unsigned int num_tx_queues;
> >> + unsigned int num_rx_queues;
> >>
> >> /* The saved address of a sent-in-place packet/buffer, for skfree(). */
> >> struct fec_enet_priv_tx_q *tx_queue[FEC_ENET_MAX_TX_QS];
> >> diff --git a/drivers/net/ethernet/freescale/fec_main.c b/drivers/net/ethernet/freescale/fec_main.c
> >> index 4c0d2ee..2240df0 100644
> >> --- a/drivers/net/ethernet/freescale/fec_main.c
> >> +++ b/drivers/net/ethernet/freescale/fec_main.c
> >> @@ -2709,6 +2709,42 @@ static void fec_reset_phy(struct platform_device *pdev)
> >> }
> >> #endif /* CONFIG_OF */
> >>
> >> +static void
> >> +fec_enet_get_queue_num(struct platform_device *pdev, int *num_tx, int *num_rx)
> >> +{
> >> + struct device_node *np = pdev->dev.of_node;
> >> + int err;
> >> +
> >> + *num_tx = *num_rx = 1;
> >> +
> >> + if (!np || !of_device_is_available(np))
> >> + return;
> >> +
> >> + /* parse the num of tx and rx queues */
> >> + err = of_property_read_u32(np, "fsl,num-tx-queues", num_tx);
> >> + err |= of_property_read_u32(np, "fsl,num-rx-queues", num_rx);
> >> + if (err) {
> >> + *num_tx = 1;
> >> + *num_rx = 1;
> > Shouldn't these be handled seperately? So that if only one of those
> > properties is given in DT the specified value for that property should
> > be used?
>
> I worry about asymmetric design in future.
>
Then why do you use two distinct properties in the first place?
> And use two property is the easy debug two directory.
>
I don't understand this sentence.
Lothar Waßmann
--
___________________________________________________________
Ka-Ro electronics GmbH | Pascalstraße 22 | D - 52076 Aachen
Phone: +49 2408 1402-0 | Fax: +49 2408 1402-10
Geschäftsführer: Matthias Kaussen
Handelsregistereintrag: Amtsgericht Aachen, HRB 4996
www.karo-electronics.de | info@xxxxxxxxxxxxxxxxxxx
___________________________________________________________
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
