From: David Jander <david@xxxxxxxxxxx>
Following changes was made:
- Add MDIO signal names
- Add missing ISB_IN2 name. Also correct ISB_nIN1. These two signals were used
together in older HW revisions. Later ISB_IN2 was removed. Software should
still be able to use both.
- Add missing CAN1 and UART line names
- Add missing ON1/2_CTRL line names
- fix CPU_* line names. The real signal names are without the CPU_ prefix, like
on imx6qdl-vicut1.dtsi
- Fix ETH_INT signal name
Signed-off-by: David Jander <david@xxxxxxxxxxx>
Signed-off-by: Oleksij Rempel <o.rempel@xxxxxxxxxxxxxx>
---
arch/arm/boot/dts/imx6dl-victgo.dts | 41 ++++++++++++++++++++++-------
1 file changed, 31 insertions(+), 10 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-victgo.dts b/arch/arm/boot/dts/imx6dl-victgo.dts
index 9cf4df3eaeb0..7fc5bb499cbc 100644
--- a/arch/arm/boot/dts/imx6dl-victgo.dts
+++ b/arch/arm/boot/dts/imx6dl-victgo.dts
@@ -408,8 +408,8 @@ &gpio1 {
"CAM2_MIRROR", "", "", "SMBALERT",
"DEBUG_0", "DEBUG_1", "", "", "", "", "", "",
"SD1_DATA0", "SD1_DATA1", "SD1_CMD", "SD1_DATA2", "SD1_CLK",
- "SD1_DATA3", "", "",
- "", "", "", "", "", "", "", "";
+ "SD1_DATA3", "ETH_MDIO", "",
+ "", "", "", "", "", "", "", "ETH_MDC";
};
&gpio2 {
@@ -417,7 +417,7 @@ &gpio2 {
"YACO_WHEEL", "YACO_RADAR", "YACO_PTO", "", "", "", "", "",
"", "LED_PWM", "", "", "",
"", "", "",
- "", "", "", "", "", "", "ISB_IN1", "ON_SWITCH",
+ "", "", "", "", "", "ISB_IN2", "ISB_nIN1", "ON_SWITCH",
"POWER_LED", "", "", "", "", "", "", "";
};
@@ -426,18 +426,20 @@ &gpio3 {
"", "", "", "", "", "", "", "",
"", "", "", "", "", "", "", "",
"ECSPI1_SCLK", "ECSPI1_MISO", "ECSPI1_MOSI", "ECSPI1_SS1",
- "CPU_ON1_FB", "USB_EXT1_OC", "USB_EXT1_PWR", "YACO_IRQ",
+ "CPU_ON1_FB", "USB_OTG_OC", "USB_OTG_PWR", "YACO_IRQ",
"TSS_TXD", "TSS_RXD", "", "", "", "", "YACO_BOOT0",
"YACO_RESET";
};
&gpio4 {
gpio-line-names =
- "", "", "", "", "", "", "", "",
- "", "", "", "", "CAN1_SR", "CAN2_SR", "CAN2_TX", "CAN2_RX",
- "", "", "DIP1_FB", "", "VCAM_EN", "", "", "",
- "CPU_LIGHT_ON", "", "ETH_RESET", "CPU_CONTACT_IN", "BL_EN",
- "BL_PWM", "ETH_INTRP", "ISB_LED";
+ "", "", "", "", "", "", "UART4_TXD", "UART4_RXD",
+ "UART5_TXD", "UART5_RXD", "CAN1_TX", "CAN1_RX", "CAN1_SR",
+ "CAN2_SR", "CAN2_TX", "CAN2_RX",
+ "", "", "DIP1_FB", "", "VCAM_EN", "ON1_CTRL", "ON2_CTRL",
+ "HITCH_IN_OUT",
+ "LIGHT_ON", "", "ETH_RESET", "CONTACT_IN", "BL_EN",
+ "BL_PWM", "ETH_INT", "ISB_LED";
};
&gpio5 {
@@ -445,11 +447,30 @@ &gpio5 {
"", "", "", "", "", "", "", "",
"TSC_PENIRQ", "TSC_BUSY", "ECSPI2_MOSI", "ECSPI2_MISO",
"ECSPI2_SS0", "ECSPI2_SCLK", "", "",
- "", "", "", "", "", "", "", "",
+ "", "", "ITU656_CLK", "I2S_MCLK", "ITU656_PDN", "AUDIO_RESET",
+ "I2S_BITCLK", "I2S_DOUT",
"I2S_LRCLK", "I2S_DIN", "I2C1_SDA", "I2C1_SCL", "YACO_AUX_RX",
"YACO_AUX_TX", "ITU656_D0", "ITU656_D1";
};
+&gpio6 {
+ gpio-line-names =
+ "ITU656_D2", "ITU656_D3", "ITU656_D4", "ITU656_D5",
+ "ITU656_D6", "ITU656_D7", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
+&gpio7 {
+ gpio-line-names =
+ "EMMC_DAT5", "EMMC_DAT4", "EMMC_CMD", "EMMC_CLK", "EMMC_DAT0",
+ "EMMC_DAT1", "EMMC_DAT2", "EMMC_DAT3",
+ "EMMC_RST", "", "", "", "CAM_DETECT", "", "", "",
+ "", "EMMC_DAT7", "EMMC_DAT6", "", "", "", "", "",
+ "", "", "", "", "", "", "", "";
+};
+
&i2c1 {
clock-frequency = <100000>;
pinctrl-names = "default";
--
2.30.2
