From: Max Krummenacher <max.krummenacher@xxxxxxxxxxx>
The following two nodes define module level functionality, move
them from the carrier board dts file to the SoM file.
While at it, reorder the properties in the gpio-keys node alphabetical.
- gpio-keys defining the wakeup pin
- memory node
The atmel touchscreen node can be used on any carrier board.
Move it from the carrier board to the module-level device tree and
keep it disabled.
Set the default pinmuxing to the dedicated connector available
on newer carrier boards and rename the pinctrl labels specifying
the INT/Reset signal to a common pattern.
pinctrl_atmel_conn - uses 107/106 pins as used on dedicated connector
pinctrl_atmel_adap - uses 28/30 pins as used with jumper wires
Signed-off-by: Max Krummenacher <max.krummenacher@xxxxxxxxxxx>
---
(no changes since v1)
arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts | 49 ------------------
arch/arm/boot/dts/imx6qdl-colibri.dtsi | 53 ++++++++++++++++++++
2 files changed, 53 insertions(+), 49 deletions(-)
diff --git a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
index 535b5c156229..dff2d35e693b 100644
--- a/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
+++ b/arch/arm/boot/dts/imx6dl-colibri-eval-v3.dts
@@ -17,12 +17,6 @@
compatible = "toradex,colibri_imx6dl-eval-v3", "toradex,colibri_imx6dl",
"fsl,imx6dl";
- /* Will be filled by the bootloader */
- memory@10000000 {
- device_type = "memory";
- reg = <0x10000000 0>;
- };
-
aliases {
i2c0 = &i2c2;
i2c1 = &i2c3;
@@ -44,20 +38,6 @@
clock-frequency = <16000000>;
clock-output-names = "clk16m";
};
-
- gpio-keys {
- compatible = "gpio-keys";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_gpio_keys>;
-
- wakeup {
- label = "Wake-Up";
- gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
- linux,code = <KEY_WAKEUP>;
- debounce-interval = <10>;
- wakeup-source;
- };
- };
};
/* Colibri SSP */
@@ -81,21 +61,6 @@
&i2c3 {
status = "okay";
- /*
- * Touchscreen is using SODIMM 28/30, also used for PWM<B>, PWM<C>,
- * aka pwm2, pwm3. so if you enable touchscreen, disable the pwms
- */
- touchscreen@4a {
- compatible = "atmel,maxtouch";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_pcap_1>;
- reg = <0x4a>;
- interrupt-parent = <&gpio1>;
- interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 28 */
- reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>; /* SODIMM 30 */
- status = "disabled";
- };
-
/* M41T0M6 real time clock on carrier board */
rtc_i2c: rtc@68 {
compatible = "st,m41t0";
@@ -111,20 +76,6 @@
&pinctrl_weim_gpio_5 &pinctrl_weim_gpio_6
&pinctrl_usbh_oc_1 &pinctrl_usbc_id_1
>;
-
- pinctrl_pcap_1: pcap1grp {
- fsl,pins = <
- MX6QDL_PAD_GPIO_9__GPIO1_IO09 0x1b0b0 /* SODIMM 28 */
- MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0x1b0b0 /* SODIMM 30 */
- >;
- };
-
- pinctrl_mxt_ts: mxttsgrp {
- fsl,pins = <
- MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0x130b0 /* SODIMM 107 */
- MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0x130b0 /* SODIMM 106 */
- >;
- };
};
&pwm1 {
diff --git a/arch/arm/boot/dts/imx6qdl-colibri.dtsi b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
index 3459bfb5c60b..1c49fd3e6286 100644
--- a/arch/arm/boot/dts/imx6qdl-colibri.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-colibri.dtsi
@@ -23,6 +23,20 @@
status = "disabled";
};
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_gpio_keys>;
+
+ wakeup {
+ debounce-interval = <10>;
+ gpios = <&gpio2 22 GPIO_ACTIVE_HIGH>; /* SODIMM 45 */
+ label = "Wake-Up";
+ linux,code = <KEY_WAKEUP>;
+ wakeup-source;
+ };
+ };
+
lcd_display: disp0 {
compatible = "fsl,imx-parallel-display";
interface-pix-fmt = "bgr666";
@@ -50,6 +64,12 @@
};
};
+ /* Will be filled by the bootloader */
+ memory@10000000 {
+ device_type = "memory";
+ reg = <0x10000000 0>;
+ };
+
panel_dpi: panel-dpi {
/*
* edt,et057090dhu: EDT 5.7" LCD TFT
@@ -564,6 +584,17 @@
scl-gpios = <&gpio1 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
sda-gpios = <&gpio1 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
status = "disabled";
+
+ atmel_mxt_ts: touchscreen@4a {
+ compatible = "atmel,maxtouch";
+ interrupt-parent = <&gpio2>;
+ interrupts = <24 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 107 */
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_atmel_conn>;
+ reg = <0x4a>;
+ reset-gpios = <&gpio1 14 GPIO_ACTIVE_HIGH>; /* SODIMM 106 */
+ status = "disabled";
+ };
};
&ipu1_di0_disp0 {
@@ -682,6 +713,28 @@
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usbh_oc_1>;
+ /* Atmel MXT touchsceen + Capacitive Touch Adapter */
+ /* NOTE: This pin group conflicts with pin groups
+ * pinctrl_pwm1/pinctrl_pwm4. Don't use them simultaneously.
+ */
+ pinctrl_atmel_adap: atmeladaptergrp {
+ fsl,pins = <
+ MX6QDL_PAD_GPIO_9__GPIO1_IO09 0xb0b1 /* SODIMM 28 */
+ MX6QDL_PAD_SD4_DAT2__GPIO2_IO10 0xb0b1 /* SODIMM 30 */
+ >;
+ };
+
+ /* Atmel MXT touchsceen + boards with built-in Capacitive Touch Connector */
+ /* NOTE: This pin group conflicts with pin groups pinctrl_weim_cs1 and
+ * pinctrl_weim_cs2. Don't use them simultaneously.
+ */
+ pinctrl_atmel_conn: atmelconnectorgrp {
+ fsl,pins = <
+ MX6QDL_PAD_EIM_CS1__GPIO2_IO24 0xb0b1 /* SODIMM_107 */
+ MX6QDL_PAD_SD2_DAT1__GPIO1_IO14 0xb0b1 /* SODIMM_106 */
+ >;
+ };
+
pinctrl_audmux: audmuxgrp {
fsl,pins = <
MX6QDL_PAD_KEY_COL0__AUD5_TXC 0x130b0
--
2.20.1
