Add a driver for the SMB2 charger block found in the Qualcomm PMI8998
and PM660.
Signed-off-by: Caleb Connolly <caleb.connolly@xxxxxxxxxx>
---
drivers/power/supply/Kconfig | 9 +
drivers/power/supply/Makefile | 1 +
drivers/power/supply/qcom_smb2.c | 930 +++++++++++++++++++++++++++++++
3 files changed, 940 insertions(+)
create mode 100644 drivers/power/supply/qcom_smb2.c
diff --git a/drivers/power/supply/Kconfig b/drivers/power/supply/Kconfig
index 1aa8323ad9f6..c72da3d75258 100644
--- a/drivers/power/supply/Kconfig
+++ b/drivers/power/supply/Kconfig
@@ -897,4 +897,13 @@ config BATTERY_UG3105
device is off or suspended, the functionality of this driver is
limited to reporting capacity only.
+config CHARGER_QCOM_SMB2
+ tristate "Qualcomm PMIC charger driver"
+ depends on MFD_SPMI_PMIC
+ depends on IIO
+ help
+ Say Y here to enable the Qualcomm PMIC Charger driver. This
+ adds support for the SMB2 switch mode battery charger found
+ in PMI8998 and related PMICs.
+
endif # POWER_SUPPLY
diff --git a/drivers/power/supply/Makefile b/drivers/power/supply/Makefile
index 7f02f36aea55..e5db9eda6a9b 100644
--- a/drivers/power/supply/Makefile
+++ b/drivers/power/supply/Makefile
@@ -108,3 +108,4 @@ obj-$(CONFIG_BATTERY_ACER_A500) += acer_a500_battery.o
obj-$(CONFIG_BATTERY_SURFACE) += surface_battery.o
obj-$(CONFIG_CHARGER_SURFACE) += surface_charger.o
obj-$(CONFIG_BATTERY_UG3105) += ug3105_battery.o
+obj-$(CONFIG_CHARGER_QCOM_SMB2) += qcom_smb2.o
diff --git a/drivers/power/supply/qcom_smb2.c b/drivers/power/supply/qcom_smb2.c
new file mode 100644
index 000000000000..63100cfc3300
--- /dev/null
+++ b/drivers/power/supply/qcom_smb2.c
@@ -0,0 +1,930 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2016-2019 The Linux Foundation. All rights reserved.
+ * Copyright (c) 2021, Linaro Ltd.
+ * Author: Caleb Connolly <caleb.connolly@xxxxxxxxxx>
+ *
+ * This driver is for the switch-mode battery charger and boost
+ * hardware found in pmi8998 and related PMICs.
+ */
+
+#include <linux/bits.h>
+#include <linux/kernel.h>
+#include <linux/minmax.h>
+#include <linux/platform_device.h>
+#include <linux/of_address.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/device.h>
+#include <linux/iio/consumer.h>
+#include <linux/mutex.h>
+#include <linux/types.h>
+#include <linux/power_supply.h>
+#include <linux/module.h>
+#include <linux/math64.h>
+#include <linux/of_irq.h>
+#include <linux/interrupt.h>
+#include <linux/workqueue.h>
+
+#define BATTERY_CHARGER_STATUS_2_REG 0x07
+#define INPUT_CURRENT_LIMITED_BIT BIT(7)
+#define CHARGER_ERROR_STATUS_SFT_EXPIRE_BIT BIT(6)
+#define CHARGER_ERROR_STATUS_BAT_OV_BIT BIT(5)
+#define CHARGER_ERROR_STATUS_BAT_TERM_MISSING_BIT BIT(4)
+#define BAT_TEMP_STATUS_MASK GENMASK(3, 0)
+#define BAT_TEMP_STATUS_SOFT_LIMIT_MASK GENMASK(3, 2)
+#define BAT_TEMP_STATUS_HOT_SOFT_LIMIT_BIT BIT(3)
+#define BAT_TEMP_STATUS_COLD_SOFT_LIMIT_BIT BIT(2)
+#define BAT_TEMP_STATUS_TOO_HOT_BIT BIT(1)
+#define BAT_TEMP_STATUS_TOO_COLD_BIT BIT(0)
+
+#define CHARGING_ENABLE_CMD_REG 0x42
+#define CHARGING_ENABLE_CMD_BIT BIT(0)
+
+#define CHGR_CFG2_REG 0x51
+#define CHG_EN_SRC_BIT BIT(7)
+#define CHG_EN_POLARITY_BIT BIT(6)
+#define PRETOFAST_TRANSITION_CFG_BIT BIT(5)
+#define BAT_OV_ECC_BIT BIT(4)
+#define I_TERM_BIT BIT(3)
+#define AUTO_RECHG_BIT BIT(2)
+#define EN_ANALOG_DROP_IN_VBATT_BIT BIT(1)
+#define CHARGER_INHIBIT_BIT BIT(0)
+
+#define FAST_CHARGE_CURRENT_CFG_REG 0x61
+#define FAST_CHARGE_CURRENT_SETTING_MASK GENMASK(7, 0)
+
+#define FLOAT_VOLTAGE_CFG_REG 0x70
+#define FLOAT_VOLTAGE_SETTING_MASK GENMASK(7, 0)
+
+#define FG_UPDATE_CFG_2_SEL_REG 0x7D
+#define SOC_LT_OTG_THRESH_SEL_BIT BIT(3)
+#define SOC_LT_CHG_RECHARGE_THRESH_SEL_BIT BIT(2)
+#define VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT BIT(1)
+#define IBT_LT_CHG_TERM_THRESH_SEL_BIT BIT(0)
+
+#define JEITA_EN_CFG_REG 0x90
+#define JEITA_EN_HARDLIMIT_BIT BIT(4)
+#define JEITA_EN_HOT_SL_FCV_BIT BIT(3)
+#define JEITA_EN_COLD_SL_FCV_BIT BIT(2)
+#define JEITA_EN_HOT_SL_CCC_BIT BIT(1)
+#define JEITA_EN_COLD_SL_CCC_BIT BIT(0)
+
+#define INT_RT_STS 0x310
+#define TYPE_C_CHANGE_RT_STS_BIT BIT(7)
+#define USBIN_ICL_CHANGE_RT_STS_BIT BIT(6)
+#define USBIN_SOURCE_CHANGE_RT_STS_BIT BIT(5)
+#define USBIN_PLUGIN_RT_STS_BIT BIT(4)
+#define USBIN_OV_RT_STS_BIT BIT(3)
+#define USBIN_UV_RT_STS_BIT BIT(2)
+#define USBIN_LT_3P6V_RT_STS_BIT BIT(1)
+#define USBIN_COLLAPSE_RT_STS_BIT BIT(0)
+
+#define BATTERY_CHARGER_STATUS_1_REG 0x06
+#define BVR_INITIAL_RAMP_BIT BIT(7)
+#define CC_SOFT_TERMINATE_BIT BIT(6)
+#define STEP_CHARGING_STATUS_SHIFT 3
+#define STEP_CHARGING_STATUS_MASK GENMASK(5, 3)
+#define BATTERY_CHARGER_STATUS_MASK GENMASK(2, 0)
+
+#define BATTERY_HEALTH_STATUS_REG 0x07
+
+#define OTG_CFG_REG 0x153
+#define OTG_RESERVED_MASK GENMASK(7, 6)
+#define DIS_OTG_ON_TLIM_BIT BIT(5)
+#define QUICKSTART_OTG_FASTROLESWAP_BIT BIT(4)
+#define INCREASE_DFP_TIME_BIT BIT(3)
+#define ENABLE_OTG_IN_DEBUG_MODE_BIT BIT(2)
+#define OTG_EN_SRC_CFG_BIT BIT(1)
+#define CONCURRENT_MODE_CFG_BIT BIT(0)
+
+#define OTG_ENG_OTG_CFG_REG 0x1C0
+#define ENG_BUCKBOOST_HALT1_8_MODE_BIT BIT(0)
+
+#define APSD_STATUS_REG 0x307
+#define APSD_STATUS_7_BIT BIT(7)
+#define HVDCP_CHECK_TIMEOUT_BIT BIT(6)
+#define SLOW_PLUGIN_TIMEOUT_BIT BIT(5)
+#define ENUMERATION_DONE_BIT BIT(4)
+#define VADP_CHANGE_DONE_AFTER_AUTH_BIT BIT(3)
+#define QC_AUTH_DONE_STATUS_BIT BIT(2)
+#define QC_CHARGER_BIT BIT(1)
+#define APSD_DTC_STATUS_DONE_BIT BIT(0)
+
+#define APSD_RESULT_STATUS_REG 0x308
+#define ICL_OVERRIDE_LATCH_BIT BIT(7)
+#define APSD_RESULT_STATUS_MASK GENMASK(6, 0)
+#define QC_3P0_BIT BIT(6)
+#define QC_2P0_BIT BIT(5)
+#define FLOAT_CHARGER_BIT BIT(4)
+#define DCP_CHARGER_BIT BIT(3)
+#define CDP_CHARGER_BIT BIT(2)
+#define OCP_CHARGER_BIT BIT(1)
+#define SDP_CHARGER_BIT BIT(0)
+
+#define TYPE_C_STATUS_1_REG 0x30B
+#define UFP_TYPEC_MASK GENMASK(7, 5)
+#define UFP_TYPEC_RDSTD_BIT BIT(7)
+#define UFP_TYPEC_RD1P5_BIT BIT(6)
+#define UFP_TYPEC_RD3P0_BIT BIT(5)
+#define UFP_TYPEC_FMB_255K_BIT BIT(4)
+#define UFP_TYPEC_FMB_301K_BIT BIT(3)
+#define UFP_TYPEC_FMB_523K_BIT BIT(2)
+#define UFP_TYPEC_FMB_619K_BIT BIT(1)
+#define UFP_TYPEC_OPEN_OPEN_BIT BIT(0)
+
+#define TYPE_C_STATUS_2_REG 0x30C
+#define DFP_RA_OPEN_BIT BIT(7)
+#define TIMER_STAGE_BIT BIT(6)
+#define EXIT_UFP_MODE_BIT BIT(5)
+#define EXIT_DFP_MODE_BIT BIT(4)
+#define DFP_TYPEC_MASK GENMASK(3, 0)
+#define DFP_RD_OPEN_BIT BIT(3)
+#define DFP_RD_RA_VCONN_BIT BIT(2)
+#define DFP_RD_RD_BIT BIT(1)
+#define DFP_RA_RA_BIT BIT(0)
+
+#define TYPE_C_STATUS_3_REG 0x30D
+#define ENABLE_BANDGAP_BIT BIT(7)
+#define U_USB_GND_NOVBUS_BIT BIT(6)
+#define U_USB_FLOAT_NOVBUS_BIT BIT(5)
+#define U_USB_GND_BIT BIT(4)
+#define U_USB_FMB1_BIT BIT(3)
+#define U_USB_FLOAT1_BIT BIT(2)
+#define U_USB_FMB2_BIT BIT(1)
+#define U_USB_FLOAT2_BIT BIT(0)
+
+#define TYPE_C_STATUS_4_REG 0x30E
+#define UFP_DFP_MODE_STATUS_BIT BIT(7)
+#define TYPEC_VBUS_STATUS_BIT BIT(6)
+#define TYPEC_VBUS_ERROR_STATUS_BIT BIT(5)
+#define TYPEC_DEBOUNCE_DONE_STATUS_BIT BIT(4)
+#define TYPEC_UFP_AUDIO_ADAPT_STATUS_BIT BIT(3)
+#define TYPEC_VCONN_OVERCURR_STATUS_BIT BIT(2)
+#define CC_ORIENTATION_BIT BIT(1)
+#define CC_ATTACHED_BIT BIT(0)
+
+#define TYPE_C_STATUS_5_REG 0x30F
+#define TRY_SOURCE_FAILED_BIT BIT(6)
+#define TRY_SINK_FAILED_BIT BIT(5)
+#define TIMER_STAGE_2_BIT BIT(4)
+#define TYPEC_LEGACY_CABLE_STATUS_BIT BIT(3)
+#define TYPEC_NONCOMP_LEGACY_CABLE_STATUS_BIT BIT(2)
+#define TYPEC_TRYSOURCE_DETECT_STATUS_BIT BIT(1)
+#define TYPEC_TRYSINK_DETECT_STATUS_BIT BIT(0)
+
+#define CMD_APSD_REG 0x341
+#define ICL_OVERRIDE_BIT BIT(1)
+#define APSD_RERUN_BIT BIT(0)
+
+#define TYPE_C_CFG_REG 0x358
+#define APSD_START_ON_CC_BIT BIT(7)
+#define WAIT_FOR_APSD_BIT BIT(6)
+#define FACTORY_MODE_DETECTION_EN_BIT BIT(5)
+#define FACTORY_MODE_ICL_3A_4A_BIT BIT(4)
+#define FACTORY_MODE_DIS_CHGING_CFG_BIT BIT(3)
+#define SUSPEND_NON_COMPLIANT_CFG_BIT BIT(2)
+#define VCONN_OC_CFG_BIT BIT(1)
+#define TYPE_C_OR_U_USB_BIT BIT(0)
+
+#define TYPE_C_CFG_2_REG 0x359
+#define TYPE_C_DFP_CURRSRC_MODE_BIT BIT(7)
+#define DFP_CC_1P4V_OR_1P6V_BIT BIT(6)
+#define VCONN_SOFTSTART_CFG_MASK GENMASK(5, 4)
+#define EN_TRY_SOURCE_MODE_BIT BIT(3)
+#define USB_FACTORY_MODE_ENABLE_BIT BIT(2)
+#define TYPE_C_UFP_MODE_BIT BIT(1)
+#define EN_80UA_180UA_CUR_SOURCE_BIT BIT(0)
+
+#define TYPE_C_CFG_3_REG 0x35A
+#define TVBUS_DEBOUNCE_BIT BIT(7)
+#define TYPEC_LEGACY_CABLE_INT_EN_BIT BIT(6)
+#define TYPEC_NONCOMPLIANT_LEGACY_CABLE_INT_EN_BIT BIT(5)
+#define TYPEC_TRYSOURCE_DETECT_INT_EN_BIT BIT(4)
+#define TYPEC_TRYSINK_DETECT_INT_EN_BIT BIT(3)
+#define EN_TRYSINK_MODE_BIT BIT(2)
+#define EN_LEGACY_CABLE_DETECTION_BIT BIT(1)
+#define ALLOW_PD_DRING_UFP_TCCDB_BIT BIT(0)
+
+#define USBIN_OPTIONS_1_CFG_REG 0x362
+#define CABLE_R_SEL_BIT BIT(7)
+#define HVDCP_AUTH_ALG_EN_CFG_BIT BIT(6)
+#define HVDCP_AUTONOMOUS_MODE_EN_CFG_BIT BIT(5)
+#define INPUT_PRIORITY_BIT BIT(4)
+#define AUTO_SRC_DETECT_BIT BIT(3)
+#define HVDCP_EN_BIT BIT(2)
+#define VADP_INCREMENT_VOLTAGE_LIMIT_BIT BIT(1)
+#define VADP_TAPER_TIMER_EN_BIT BIT(0)
+
+#define USBIN_OPTIONS_2_CFG_REG 0x363
+#define WIPWR_RST_EUD_CFG_BIT BIT(7)
+#define SWITCHER_START_CFG_BIT BIT(6)
+#define DCD_TIMEOUT_SEL_BIT BIT(5)
+#define OCD_CURRENT_SEL_BIT BIT(4)
+#define SLOW_PLUGIN_TIMER_EN_CFG_BIT BIT(3)
+#define FLOAT_OPTIONS_MASK GENMASK(2, 0)
+#define FLOAT_DIS_CHGING_CFG_BIT BIT(2)
+#define SUSPEND_FLOAT_CFG_BIT BIT(1)
+#define FORCE_FLOAT_SDP_CFG_BIT BIT(0)
+
+#define TAPER_TIMER_SEL_CFG_REG 0x364
+#define TYPEC_SPARE_CFG_BIT BIT(7)
+#define TYPEC_DRP_DFP_TIME_CFG_BIT BIT(5)
+#define TAPER_TIMER_SEL_MASK GENMASK(1, 0)
+
+#define USBIN_LOAD_CFG_REG 0x365
+#define USBIN_OV_CH_LOAD_OPTION_BIT BIT(7)
+#define ICL_OVERRIDE_AFTER_APSD_BIT BIT(4)
+
+#define USBIN_ICL_OPTIONS_REG 0x366
+#define CFG_USB3P0_SEL_BIT BIT(2)
+#define USB51_MODE_BIT BIT(1)
+#define USBIN_MODE_CHG_BIT BIT(0)
+
+#define TYPE_C_INTRPT_ENB_SOFTWARE_CTRL_REG 0x368
+#define EXIT_SNK_BASED_ON_CC_BIT BIT(7)
+#define VCONN_EN_ORIENTATION_BIT BIT(6)
+#define TYPEC_VCONN_OVERCURR_INT_EN_BIT BIT(5)
+#define VCONN_EN_SRC_BIT BIT(4)
+#define VCONN_EN_VALUE_BIT BIT(3)
+#define TYPEC_POWER_ROLE_CMD_MASK GENMASK(2, 0)
+#define UFP_EN_CMD_BIT BIT(2)
+#define DFP_EN_CMD_BIT BIT(1)
+#define TYPEC_DISABLE_CMD_BIT BIT(0)
+
+#define USBIN_CURRENT_LIMIT_CFG_REG 0x370
+#define USBIN_CURRENT_LIMIT_MASK GENMASK(7, 0)
+
+#define USBIN_AICL_OPTIONS_CFG_REG 0x380
+#define SUSPEND_ON_COLLAPSE_USBIN_BIT BIT(7)
+#define USBIN_AICL_HDC_EN_BIT BIT(6)
+#define USBIN_AICL_START_AT_MAX_BIT BIT(5)
+#define USBIN_AICL_RERUN_EN_BIT BIT(4)
+#define USBIN_AICL_ADC_EN_BIT BIT(3)
+#define USBIN_AICL_EN_BIT BIT(2)
+#define USBIN_HV_COLLAPSE_RESPONSE_BIT BIT(1)
+#define USBIN_LV_COLLAPSE_RESPONSE_BIT BIT(0)
+
+#define DC_ENG_SSUPPLY_CFG2_REG 0x4C1
+#define ENG_SSUPPLY_IVREF_OTG_SS_MASK GENMASK(2, 0)
+#define OTG_SS_SLOW 0x3
+
+#define DCIN_AICL_REF_SEL_CFG_REG 0x481
+#define DCIN_CONT_AICL_THRESHOLD_CFG_MASK GENMASK(5, 0)
+
+#define WI_PWR_OPTIONS_REG 0x495
+#define CHG_OK_BIT BIT(7)
+#define WIPWR_UVLO_IRQ_OPT_BIT BIT(6)
+#define BUCK_HOLDOFF_ENABLE_BIT BIT(5)
+#define CHG_OK_HW_SW_SELECT_BIT BIT(4)
+#define WIPWR_RST_ENABLE_BIT BIT(3)
+#define DCIN_WIPWR_IRQ_SELECT_BIT BIT(2)
+#define AICL_SWITCH_ENABLE_BIT BIT(1)
+#define ZIN_ICL_ENABLE_BIT BIT(0)
+
+#define ICL_STATUS_REG 0x607
+#define INPUT_CURRENT_LIMIT_MASK GENMASK(7, 0)
+
+#define POWER_PATH_STATUS_REG 0x60B
+#define P_PATH_INPUT_SS_DONE_BIT BIT(7)
+#define P_PATH_USBIN_SUSPEND_STS_BIT BIT(6)
+#define P_PATH_DCIN_SUSPEND_STS_BIT BIT(5)
+#define P_PATH_USE_USBIN_BIT BIT(4)
+#define P_PATH_USE_DCIN_BIT BIT(3)
+#define P_PATH_POWER_PATH_MASK GENMASK(2, 1)
+#define P_PATH_VALID_INPUT_POWER_SOURCE_STS_BIT BIT(0)
+
+#define WD_CFG_REG 0x651
+#define WATCHDOG_TRIGGER_AFP_EN_BIT BIT(7)
+#define BARK_WDOG_INT_EN_BIT BIT(6)
+#define BITE_WDOG_INT_EN_BIT BIT(5)
+#define SFT_AFTER_WDOG_IRQ_MASK GENMASK(4, 3)
+#define WDOG_IRQ_SFT_BIT BIT(2)
+#define WDOG_TIMER_EN_ON_PLUGIN_BIT BIT(1)
+#define WDOG_TIMER_EN_BIT BIT(0)
+
+#define AICL_RERUN_TIME_CFG_REG 0x661
+#define AICL_RERUN_TIME_MASK GENMASK(1, 0)
+
+#define SDP_CURRENT_UA 500000
+#define CDP_CURRENT_UA 1500000
+#define DCP_CURRENT_UA 1500000
+
+enum charger_status {
+ TRICKLE_CHARGE = 0,
+ PRE_CHARGE,
+ FAST_CHARGE,
+ FULLON_CHARGE,
+ TAPER_CHARGE,
+ TERMINATE_CHARGE,
+ INHIBIT_CHARGE,
+ DISABLE_CHARGE,
+};
+
+struct smb2_register {
+ u16 addr;
+ u8 mask;
+ u8 val;
+};
+
+/**
+ * struct smb2_chip - smb2 chip structure
+ * @dev: Device reference for power_supply
+ * @base: Base address for smb2 registers
+ * @regmap: Register map
+ * @reg_lock: Mutex for register access
+ * @batt_info: Battery data from DT
+ * @usbin_i_chan: USBIN current measurement channel
+ * @usbin_v_chan: USBIN voltage measurement channel
+ * @chg_psy: Charger power supply instance
+ * @usb_present: True if a charger is attached
+ */
+struct smb2_chip {
+ struct device *dev;
+ const char *name;
+ unsigned int base;
+ struct regmap *regmap;
+ struct mutex reg_lock;
+ struct power_supply_battery_info *batt_info;
+
+ struct delayed_work status_change_work;
+
+ struct iio_channel *usbin_i_chan;
+ struct iio_channel *usbin_v_chan;
+
+ struct power_supply *chg_psy;
+
+ bool usb_present;
+};
+
+static enum power_supply_property smb2_properties[] = {
+ POWER_SUPPLY_PROP_MANUFACTURER, POWER_SUPPLY_PROP_MODEL_NAME,
+ POWER_SUPPLY_PROP_CURRENT_MAX, POWER_SUPPLY_PROP_CURRENT_NOW,
+ POWER_SUPPLY_PROP_VOLTAGE_NOW, POWER_SUPPLY_PROP_STATUS,
+ POWER_SUPPLY_PROP_HEALTH, POWER_SUPPLY_PROP_ONLINE,
+ POWER_SUPPLY_PROP_USB_TYPE,
+};
+
+static enum power_supply_usb_type smb2_usb_types[] = {
+ POWER_SUPPLY_USB_TYPE_SDP, POWER_SUPPLY_USB_TYPE_DCP,
+ POWER_SUPPLY_USB_TYPE_CDP, POWER_SUPPLY_USB_TYPE_C,
+ POWER_SUPPLY_USB_TYPE_PD_DRP
+};
+
+/*
+ * Qualcomm "automatic power source detection" aka APSD
+ * tells us what type of charger we're connected to.
+ */
+static int smb2_apsd_get_charger_type(struct smb2_chip *chip, int *val)
+{
+ int rc;
+ unsigned int apsd_stat, stat;
+
+ mutex_lock(&chip->reg_lock);
+
+ rc = regmap_read(chip->regmap, chip->base + APSD_STATUS_REG,
+ &apsd_stat);
+ if (rc < 0) {
+ dev_err(chip->dev, "Failed to read apsd status, rc = %d", rc);
+ return rc;
+ }
+ if (!(apsd_stat & APSD_DTC_STATUS_DONE_BIT)) {
+ dev_err(chip->dev, "Apsd not ready");
+ return -EAGAIN;
+ }
+
+ rc = regmap_read(chip->regmap, chip->base + APSD_RESULT_STATUS_REG,
+ &stat);
+ if (rc < 0) {
+ dev_err(chip->dev, "Failed to read apsd result, rc = %d", rc);
+ return rc;
+ }
+
+ mutex_unlock(&chip->reg_lock);
+
+ stat &= APSD_RESULT_STATUS_MASK;
+
+ if (stat & CDP_CHARGER_BIT) {
+ *val = POWER_SUPPLY_USB_TYPE_CDP;
+ } else if (stat &
+ (DCP_CHARGER_BIT | OCP_CHARGER_BIT | FLOAT_CHARGER_BIT)) {
+ *val = POWER_SUPPLY_USB_TYPE_DCP;
+ } else { /* SDP_CHARGER_BIT (or others) */
+ *val = POWER_SUPPLY_USB_TYPE_SDP;
+ }
+
+ return 0;
+}
+
+int smb2_get_prop_usb_online(struct smb2_chip *chip, int *val)
+{
+ unsigned int stat;
+ int rc;
+
+ rc = regmap_read(chip->regmap, chip->base + POWER_PATH_STATUS_REG,
+ &stat);
+ if (rc < 0) {
+ dev_err(chip->dev, "Couldn't read POWER_PATH_STATUS! ret=%d\n",
+ rc);
+ return rc;
+ }
+
+ *val = (stat & P_PATH_USE_USBIN_BIT) &&
+ (stat & P_PATH_VALID_INPUT_POWER_SOURCE_STS_BIT);
+ return rc;
+}
+
+int smb2_get_prop_status(struct smb2_chip *chip, int *val)
+{
+ int usb_online_val;
+ unsigned int stat;
+ int rc;
+ bool usb_online;
+
+ mutex_lock(&chip->reg_lock);
+
+ rc = smb2_get_prop_usb_online(chip, &usb_online_val);
+ if (rc < 0) {
+ dev_err(chip->dev, "Couldn't get usb online property rc = %d\n",
+ rc);
+ return rc;
+ }
+ usb_online = (bool)usb_online_val;
+
+ if (!usb_online) {
+ *val = POWER_SUPPLY_STATUS_DISCHARGING;
+ return rc;
+ }
+
+ rc = regmap_read(chip->regmap,
+ chip->base + BATTERY_CHARGER_STATUS_1_REG, &stat);
+ if (rc < 0) {
+ dev_err(chip->dev,
+ "Failed to read charging status ret=%d\n", rc);
+ return rc;
+ }
+
+ mutex_unlock(&chip->reg_lock);
+
+ stat = stat & BATTERY_CHARGER_STATUS_MASK;
+
+ switch (stat) {
+ case TRICKLE_CHARGE:
+ case PRE_CHARGE:
+ case FAST_CHARGE:
+ case FULLON_CHARGE:
+ case TAPER_CHARGE:
+ *val = POWER_SUPPLY_STATUS_CHARGING;
+ return rc;
+ case DISABLE_CHARGE:
+ *val = POWER_SUPPLY_STATUS_NOT_CHARGING;
+ return rc;
+ case TERMINATE_CHARGE:
+ *val = POWER_SUPPLY_STATUS_FULL;
+ return rc;
+ case INHIBIT_CHARGE:
+ default:
+ *val = POWER_SUPPLY_STATUS_UNKNOWN;
+ return rc;
+ }
+}
+
+static inline int smb2_get_current_limit(struct smb2_chip *chip,
+ unsigned int *val)
+{
+ int rc = regmap_read(chip->regmap, chip->base + ICL_STATUS_REG, val);
+
+ if (rc >= 0)
+ *val *= 25000;
+ return rc;
+}
+
+static inline int smb2_set_current_limit(struct smb2_chip *chip,
+ unsigned int val)
+{
+ unsigned char val_raw;
+
+ if (val > 4800000) {
+ dev_err(chip->dev,
+ "Can't set current limit higher than 4800000uA");
+ return -EINVAL;
+ }
+ val_raw = val / 25000;
+ return regmap_write(chip->regmap,
+ chip->base + USBIN_CURRENT_LIMIT_CFG_REG, val_raw);
+}
+
+void smb2_status_change_work(struct work_struct *work)
+{
+ struct smb2_chip *chip =
+ container_of(work, struct smb2_chip, status_change_work.work);
+ unsigned int charger_type, current_ua;
+ int usb_online, count, rc;
+
+ mutex_lock(&chip->reg_lock);
+
+ smb2_get_prop_usb_online(chip, &usb_online);
+ if (usb_online == 0)
+ return;
+
+ for (count = 0; count < 3; count++) {
+ dev_info(chip->dev, "get charger type retry %d\n", count);
+ rc = smb2_apsd_get_charger_type(chip, &charger_type);
+ if (rc == 0)
+ break;
+ msleep(100);
+ }
+
+ if (rc < 0) {
+ rc = regmap_update_bits(chip->regmap, chip->base + CMD_APSD_REG,
+ APSD_RERUN_BIT, APSD_RERUN_BIT);
+ schedule_delayed_work(&chip->status_change_work,
+ msecs_to_jiffies(1500));
+ return;
+ }
+
+ switch (charger_type) {
+ case POWER_SUPPLY_USB_TYPE_CDP:
+ current_ua = CDP_CURRENT_UA;
+ break;
+ case POWER_SUPPLY_USB_TYPE_DCP:
+ current_ua = DCP_CURRENT_UA;
+ break;
+ case POWER_SUPPLY_USB_TYPE_SDP:
+ default:
+ current_ua = SDP_CURRENT_UA;
+ break;
+ }
+
+ smb2_set_current_limit(chip, current_ua);
+ mutex_unlock(&chip->reg_lock);
+ power_supply_changed(chip->chg_psy);
+}
+
+int smb2_get_iio_chan(struct smb2_chip *chip, struct iio_channel *chan,
+ int *val)
+{
+ int rc = 0;
+ union power_supply_propval status;
+
+ rc = power_supply_get_property(chip->chg_psy, POWER_SUPPLY_PROP_STATUS,
+ &status);
+ if (rc < 0 || status.intval != POWER_SUPPLY_STATUS_CHARGING) {
+ *val = 0;
+ return 0;
+ }
+
+ if (IS_ERR(chan)) {
+ dev_err(chip->dev, "Failed to chan, err = %li", PTR_ERR(chan));
+ return PTR_ERR(chan);
+ }
+
+ rc = iio_read_channel_processed(chan, val);
+ return rc;
+}
+
+int smb2_get_prop_health(struct smb2_chip *chip, int *val)
+{
+ int rc;
+ unsigned int stat;
+
+ *val = POWER_SUPPLY_HEALTH_UNKNOWN;
+
+ rc = regmap_read(chip->regmap,
+ chip->base + BATTERY_CHARGER_STATUS_2_REG, &stat);
+ if (rc < 0) {
+ dev_err(chip->dev, "Couldn't read charger status rc=%d\n", rc);
+ return rc;
+ }
+
+ switch (stat & BATTERY_CHARGER_STATUS_MASK) {
+ case CHARGER_ERROR_STATUS_BAT_OV_BIT:
+ *val = POWER_SUPPLY_HEALTH_OVERVOLTAGE;
+ return 0;
+ case BAT_TEMP_STATUS_TOO_COLD_BIT:
+ *val = POWER_SUPPLY_HEALTH_COLD;
+ return 0;
+ case BAT_TEMP_STATUS_TOO_HOT_BIT:
+ *val = POWER_SUPPLY_HEALTH_OVERHEAT;
+ return 0;
+ case BAT_TEMP_STATUS_COLD_SOFT_LIMIT_BIT:
+ *val = POWER_SUPPLY_HEALTH_COOL;
+ return 0;
+ case BAT_TEMP_STATUS_HOT_SOFT_LIMIT_BIT:
+ *val = POWER_SUPPLY_HEALTH_WARM;
+ return 0;
+ default:
+ *val = POWER_SUPPLY_HEALTH_GOOD;
+ return 0;
+ }
+}
+
+static int smb2_get_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ union power_supply_propval *val)
+{
+ struct smb2_chip *chip = power_supply_get_drvdata(psy);
+ int error = 0;
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_MANUFACTURER:
+ val->strval = "Qualcomm";
+ return 0;
+ case POWER_SUPPLY_PROP_MODEL_NAME:
+ val->strval = chip->name;
+ return 0;
+ case POWER_SUPPLY_PROP_CURRENT_MAX:
+ error = smb2_get_current_limit(chip, &val->intval);
+ return 0;
+ case POWER_SUPPLY_PROP_CURRENT_NOW:
+ error = smb2_get_iio_chan(chip, chip->usbin_i_chan,
+ &val->intval);
+ return 0;
+ case POWER_SUPPLY_PROP_VOLTAGE_NOW:
+ error = smb2_get_iio_chan(chip, chip->usbin_v_chan,
+ &val->intval);
+ return 0;
+ case POWER_SUPPLY_PROP_ONLINE:
+ error = smb2_get_prop_usb_online(chip, &val->intval);
+ return 0;
+ case POWER_SUPPLY_PROP_STATUS:
+ error = smb2_get_prop_status(chip, &val->intval);
+ return 0;
+ case POWER_SUPPLY_PROP_HEALTH:
+ error = smb2_get_prop_health(chip, &val->intval);
+ return 0;
+ case POWER_SUPPLY_PROP_USB_TYPE:
+ error = smb2_apsd_get_charger_type(chip, &val->intval);
+ return 0;
+ default:
+ dev_err(chip->dev, "invalid property: %d\n", psp);
+ return -EINVAL;
+ }
+}
+
+static int smb2_set_property(struct power_supply *psy,
+ enum power_supply_property psp,
+ const union power_supply_propval *val)
+{
+ struct smb2_chip *chip = power_supply_get_drvdata(psy);
+ int error = 0;
+
+ dev_info(chip->dev, "Setting property: %d", psp);
+
+ mutex_lock(&chip->reg_lock);
+
+ switch (psp) {
+ case POWER_SUPPLY_PROP_CURRENT_MAX:
+ error = smb2_set_current_limit(chip, val->intval);
+ break;
+ default:
+ dev_err(chip->dev, "No setter for property: %d\n", psp);
+ error = -EINVAL;
+ }
+
+ mutex_unlock(&chip->reg_lock);
+
+ return error;
+}
+
+static int smb2_property_is_writable(struct power_supply *psy,
+ enum power_supply_property psp)
+{
+ switch (psp) {
+ case POWER_SUPPLY_PROP_CURRENT_MAX:
+ return 1;
+ default:
+ return 0;
+ }
+}
+
+irqreturn_t smb2_handle_usb_plugin(int irq, void *data)
+{
+ struct smb2_chip *chip = data;
+ int rc;
+ unsigned int intrt_stat;
+
+ rc = regmap_read(chip->regmap, chip->base + INT_RT_STS, &intrt_stat);
+ if (rc < 0) {
+ dev_err(chip->dev,
+ "Couldn't read USB status from reg! ret=%d\n", rc);
+ return rc;
+ }
+
+ chip->usb_present = (bool)(intrt_stat & USBIN_PLUGIN_RT_STS_BIT);
+
+ power_supply_changed(chip->chg_psy);
+
+ schedule_delayed_work(&chip->status_change_work,
+ msecs_to_jiffies(1000));
+
+ return IRQ_HANDLED;
+}
+
+static const struct power_supply_desc smb2_psy_desc = {
+ .name = "usb",
+ .type = POWER_SUPPLY_TYPE_USB,
+ .usb_types = smb2_usb_types,
+ .num_usb_types = ARRAY_SIZE(smb2_usb_types),
+ .properties = smb2_properties,
+ .num_properties = ARRAY_SIZE(smb2_properties),
+ .get_property = smb2_get_property,
+ .set_property = smb2_set_property,
+ .property_is_writeable = smb2_property_is_writable,
+};
+
+/* Init sequence derived from downstream driver */
+static struct smb2_register smb2_init_seq[] = {
+ { .addr = AICL_RERUN_TIME_CFG_REG,
+ .mask = AICL_RERUN_TIME_MASK,
+ .val = 0 },
+ { .addr = USBIN_AICL_OPTIONS_CFG_REG,
+ .mask = USBIN_AICL_START_AT_MAX_BIT | USBIN_AICL_ADC_EN_BIT,
+ .val = 0 },
+ /*
+ * By default configure us as an upstream facing port
+ * FIXME: for OTG we should set UFP_EN_CMD_BIT and DFP_EN_CMD_BIT both to 0
+ */
+ { .addr = TYPE_C_INTRPT_ENB_SOFTWARE_CTRL_REG,
+ .mask = TYPEC_POWER_ROLE_CMD_MASK | VCONN_EN_SRC_BIT |
+ VCONN_EN_VALUE_BIT,
+ .val = VCONN_EN_SRC_BIT | UFP_EN_CMD_BIT },
+ /*
+ * disable Type-C factory mode and stay in Attached.SRC state when VCONN
+ * over-current happens
+ */
+ { .addr = TYPE_C_CFG_REG,
+ .mask = FACTORY_MODE_DETECTION_EN_BIT | VCONN_OC_CFG_BIT,
+ .val = 0 },
+ /* Configure VBUS for software control */
+ { .addr = OTG_CFG_REG, .mask = OTG_EN_SRC_CFG_BIT, .val = 0 },
+ { .addr = FG_UPDATE_CFG_2_SEL_REG,
+ .mask = SOC_LT_CHG_RECHARGE_THRESH_SEL_BIT |
+ VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT,
+ .val = VBT_LT_CHG_RECHARGE_THRESH_SEL_BIT },
+ /* Enable automatic input current limit */
+ { .addr = USBIN_AICL_OPTIONS_CFG_REG,
+ .mask = USBIN_AICL_EN_BIT,
+ .val = 1 },
+ { .addr = USBIN_OPTIONS_1_CFG_REG, .mask = HVDCP_EN_BIT, .val = 0 },
+ { .addr = CHARGING_ENABLE_CMD_REG,
+ .mask = CHARGING_ENABLE_CMD_BIT,
+ .val = CHARGING_ENABLE_CMD_BIT },
+ { .addr = USBIN_LOAD_CFG_REG,
+ .mask = ICL_OVERRIDE_AFTER_APSD_BIT,
+ .val = ICL_OVERRIDE_AFTER_APSD_BIT },
+ { .addr = CHGR_CFG2_REG,
+ .mask = CHG_EN_POLARITY_BIT | CHG_EN_SRC_BIT,
+ .val = 0 },
+ { .addr = TYPE_C_INTRPT_ENB_SOFTWARE_CTRL_REG,
+ .mask = UFP_EN_CMD_BIT,
+ .val = UFP_EN_CMD_BIT },
+ /* Set the default SDP charger type to a 500ma USB 2.0 port
+ * and apply ICL override? (OnePlus 6 hack??)
+ */
+ { .addr = USBIN_ICL_OPTIONS_REG,
+ .mask = USB51_MODE_BIT | USBIN_MODE_CHG_BIT,
+ .val = USB51_MODE_BIT }, //| USBIN_MODE_CHG_BIT },
+};
+
+static int smb2_init_hw(struct smb2_chip *chip)
+{
+ int rc, i;
+
+ for (i = 0; i < ARRAY_SIZE(smb2_init_seq); i++) {
+ dev_info(chip->dev, "%d: Writing 0x%02x to 0x%02x\n", i,
+ smb2_init_seq[i].val, smb2_init_seq[i].addr);
+ rc = regmap_update_bits(chip->regmap,
+ chip->base + smb2_init_seq[i].addr,
+ smb2_init_seq[i].mask,
+ smb2_init_seq[i].val);
+ if (rc < 0) {
+ dev_err(chip->dev,
+ "%s: Failed to write 0x%02x to 0x%02x: %d\n",
+ __func__, smb2_init_seq[i].val,
+ smb2_init_seq[i].addr, rc);
+ return rc;
+ }
+ }
+
+ smb2_set_current_limit(chip, 1950 * 1000);
+ return rc;
+}
+
+static int smb2_probe(struct platform_device *pdev)
+{
+ struct power_supply_config supply_config = {};
+ struct smb2_chip *chip;
+ int rc = 0, irq;
+
+ chip = devm_kzalloc(&pdev->dev, sizeof(*chip), GFP_KERNEL);
+ if (!chip)
+ return -ENOMEM;
+
+ chip->dev = &pdev->dev;
+ chip->name = pdev->name;
+ mutex_init(&chip->reg_lock);
+
+ chip->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!chip->regmap) {
+ dev_err(chip->dev, "failed to locate the regmap\n");
+ return -ENODEV;
+ }
+
+ rc = device_property_read_u32(chip->dev, "reg", &chip->base);
+ if (rc < 0) {
+ dev_err(chip->dev, "Couldn't read base address from dt: %d\n",
+ rc);
+ return rc;
+ }
+
+ irq = of_irq_get_byname(pdev->dev.of_node, "usb-plugin");
+ if (irq < 0) {
+ dev_err(&pdev->dev, "Couldn't get irq usb-plugin byname\n");
+ return irq;
+ }
+
+ rc = devm_request_threaded_irq(chip->dev, irq, NULL,
+ smb2_handle_usb_plugin, IRQF_ONESHOT,
+ "usb-plugin", chip);
+ if (rc < 0) {
+ dev_err(chip->dev, "Couldn't request irq %d\n", irq);
+ return rc;
+ }
+
+ chip->usbin_v_chan = iio_channel_get(chip->dev, "usbin_v");
+ chip->usbin_i_chan = iio_channel_get(chip->dev, "usbin_i");
+
+ /* RRADC should probe before us, but just in case it doesn't */
+ if (PTR_ERR(chip->usbin_v_chan) == -EPROBE_DEFER ||
+ PTR_ERR(chip->usbin_i_chan) == -EPROBE_DEFER) {
+ return -EPROBE_DEFER;
+ }
+
+ rc = smb2_init_hw(chip);
+ if (rc < 0) {
+ dev_err(chip->dev, "Couldn't init hw %d\n", rc);
+ return rc;
+ }
+
+ supply_config.drv_data = chip;
+ supply_config.of_node = pdev->dev.of_node;
+
+ chip->chg_psy = devm_power_supply_register(chip->dev, &smb2_psy_desc,
+ &supply_config);
+ if (IS_ERR(chip->chg_psy)) {
+ dev_err(&pdev->dev, "failed to register power supply\n");
+ return PTR_ERR(chip->chg_psy);
+ }
+
+ rc = power_supply_get_battery_info(chip->chg_psy, &chip->batt_info);
+ if (rc) {
+ dev_err(&pdev->dev, "Failed to get battery info: %d\n", rc);
+ return rc;
+ }
+
+ INIT_DELAYED_WORK(&chip->status_change_work, smb2_status_change_work);
+
+ rc = chip->batt_info->voltage_max_design_uv;
+ rc = regmap_update_bits(chip->regmap,
+ chip->base + FLOAT_VOLTAGE_CFG_REG,
+ FLOAT_VOLTAGE_SETTING_MASK, rc / 1000);
+ if (rc < 0)
+ dev_err(chip->dev, "Couldn't set vbat max rc = %d\n", rc);
+
+ platform_set_drvdata(pdev, chip);
+
+ /* trigger the IRQ to set up initial state */
+ smb2_handle_usb_plugin(irq, chip);
+
+ return 0;
+}
+
+static int smb2_remove(struct platform_device *pdev)
+{
+ struct smb2_chip *chip = platform_get_drvdata(pdev);
+
+ power_supply_put_battery_info(chip->chg_psy, chip->batt_info);
+ return 0;
+}
+
+static const struct of_device_id fg_match_id_table[] = {
+ { .compatible = "qcom,pmi8998-smb2" },
+ { /* sentinal */ }
+};
+MODULE_DEVICE_TABLE(of, fg_match_id_table);
+
+static struct platform_driver qcom_spmi_smb2 = {
+ .probe = smb2_probe,
+ .remove = smb2_remove,
+ .driver = {
+ .name = "qcom-spmi-smb2",
+ .of_match_table = fg_match_id_table,
+ },
+};
+
+module_platform_driver(qcom_spmi_smb2);
+
+MODULE_AUTHOR("Caleb Connolly <caleb.connolly@xxxxxxxxxx>");
+MODULE_DESCRIPTION("Qualcomm SMB2 Charger Driver");
+MODULE_LICENSE("GPL");
--
2.35.1
