On Thu, Mar 24, 2022 at 04:37:19AM +0300, Serge Semin wrote: > Currently both DW PCIe Root Port and End-point DT bindings are too generic > to be used as a descriptive set the device properties. Yes, it's very handy > to have them that way so the DT-schemas could be used to evaluate as many > DW PCIe-related DT-nodes as possible. But at the same time they don't > provide well defined DW PCIe RP/EP DT interface description thus leaving > too much flexibility for the new platforms, no encouraging the developers > to preserve a compatible interface. > > Instead of currently implemented approach we suggest to be more > restrictive and yet preserve some level of flexibility in the DW PCIe > DT-bindings description. The device tree DT-schema is split up into > three parts: a common YAML-schema applicable for both DWC Root Port and > End-point controller configs, DWC PCIe Root Port-specific YAML-schema > and DWC PCIe End-point-specific YAML-schema, where > 1) pci/snps,dw-pcie-common.yaml - The common DT-schema describes the most > generic constraints of the "reg", "interrupts", "clocks", "resets" and > "phys" properties together with a set of common for both device types > PCIe/AXI bus properties like a maximum number of lanes or a maximum link > speed, number of inbound and outbound iATU windows. In addition to that a > set of schema definitions declared under the "$defs" property with "reg", > "interrupt", "clock" and "reset" names common for DWC PCIe Root Port and > End-point devices. They can be used by the successive DT-schemas in case > they are supposed to be compatible with the generic DWC PCIe controller > DT-bindings. > 2) pci/snps,dw-pcie.yaml, pci/snps,dw-pcie-ep.yaml - generic DW PCIe Root > Port and End-point DT-bindings which aside with the device-specific > properties set also contain more restrictive constraints. All new DW PCIe > platforms are supposed to be compatible with one of these bindings by > using "allOf: " property and additionally defining their own constraints > to close up the DT-bindings set. > > So to speak in case if a DW PCIe-based device for some reason has too many > specific properties or it's bindings have already been defined in a > non-generic way, it's DT-schema is supposed to include 1) YAML-file and > provide its own constraints. Otherwise the ready-to-use bindings from 2) > should be utilized. There only two DT-schemas compatible with 2) at the > moment are samsung,axynos-pcie.yaml and intel-gw-pcie.yaml. The > rest of the DW PCIe-related DT-schemas are supposed to use more generic > DW PCIe DT-bindings - pci/snps,dw-pcie-common.yaml. > > Note the provided here generic properties and their possible values are > derived from the DW PCIe RC/EP hardware manuals and from the interface > implemented in the driver. The DT-bindings schemas are created to be as > full as possible with detailed properties/names description for the > easier interface comprehension and new platforms bindings development. > > Also note since there are no generic DT-nodes can be found in the kernel > dts-es which would have a pure "snps,dw-pcie" compatible string, these > DT-bindings have been created to not be selected by default for > evaluation. They are supposed to be used by the new vendor-specific > DT-schemas to at least stop adding new bindings for the same set of DWC > PCIe signals or properties. > > Signed-off-by: Serge Semin <Sergey.Semin@xxxxxxxxxxxxxxxxxxxx> > > --- > > Rob, if you comment the "select: false" line out you'll get a lot of "'*' > is not of type 'array'" errors on the dt_bindings_check command execution. > I have spend tons of time trying to figure out what was wrong, but still > failed to find out a solution. For some reason the "$ref"-ed schemas > defined under the "$defs" basic property are considered by the parser as > defining an array. No matter whether I specified the "type: string" > keyword or not, as long as there is "enum" or "oneOf" keyword used in the > "*-names" property definition in "$defs" it's considered as describing an > array thus causing the errors like: As-is, there were lots of errors... > > > DTC Documentation/devicetree/bindings/pci/snps,dw-pcie.example.dt.yaml > > CHECK Documentation/devicetree/bindings/pci/snps,dw-pcie.example.dt.yaml > > /.../snps,dw-pcie.example.dt.yaml: pcie@1f052000: reg-names:0: 'oneOf' conditional failed, one must be fixed: > > 'dbi' is not of type 'array' > > From schema: /.../snps,dw-pcie.yaml > > /.../snps,dw-pcie.example.dt.yaml: pcie@1f052000: reg-names:1: 'oneOf' conditional failed, one must be fixed: > > 'config' is not of type 'array' > > From schema: /.../snps,dw-pcie.yaml > > /.../snps,dw-pcie.example.dt.yaml: pcie@1f052000: interrupt-names:0: 'anyOf' conditional failed, one must be fixed: > > /.../snps,dw-pcie.example.dt.yaml: pcie@1f052000: interrupt-names:0: 'oneOf' conditional failed, one must be fixed: > > 'msi' is not of type 'array' > > /../snps,dw-pcie.example.dt.yaml: pcie@1f052000: interrupt-names:0: 'oneOf' conditional failed, one must be fixed: > > 'msi' is not of type 'array' > > From schema: /.../snps,dw-pcie.yaml > > As soon as I manually moved the same "$defs"-schemas into the places they > are referenced to, the errors disappeared and the DT-schemas validation > worked as expected by the semantics. > > As I see it there must be some bug in the parser, otherwise I am out of > ideas how to implement the suggested in this patch design pattern. Rob, > could you take a look at the DT-schemas and help me out with debugging the > problem described above? There is at least an error in your schema, details latter on. It could be an issue in the fixups which in general convert schemas for strings to string arrays and scalars/arrays to matrix. You have to look at processed-schema.json to debug it. The other thing is 'oneOf' errors can be confusing in terms of error messages because the tooling doesn't really know which entry had the least error. Like the type was right, but some secondary constraint failed (as what's secondary is not expressed in any way). I would debug it further, but I don't really like the end result. I think it's too hard to follow. For the most part, we avoid $refs at the property level across different schema files with the big exception being types.yaml. $defs are also used sparingly. The challenge is that json-schema by default will be silent on schemas misformed in lots of ways. Our meta-schema adds a lot of constraints which limits what the schemas can look like and ensures schemas are valid. It also allows me to define new constraints rather than repeat the same review comment over and over. > --- > .../bindings/pci/fsl,imx6q-pcie.yaml | 5 +- > .../bindings/pci/hisilicon,kirin-pcie.yaml | 4 +- > .../bindings/pci/sifive,fu740-pcie.yaml | 4 +- > .../bindings/pci/snps,dw-pcie-common.yaml | 298 ++++++++++++++++++ > .../bindings/pci/snps,dw-pcie-ep.yaml | 143 ++++++--- > .../devicetree/bindings/pci/snps,dw-pcie.yaml | 189 +++++++---- > .../bindings/pci/toshiba,visconti-pcie.yaml | 2 +- > 7 files changed, 524 insertions(+), 121 deletions(-) > create mode 100644 Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml > diff --git a/Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml b/Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml > new file mode 100644 > index 000000000000..27fe1f5c450f > --- /dev/null > +++ b/Documentation/devicetree/bindings/pci/snps,dw-pcie-common.yaml > @@ -0,0 +1,298 @@ > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) > +%YAML 1.2 > +--- > +$id: http://devicetree.org/schemas/pci/snps,dw-pcie-common.yaml# > +$schema: http://devicetree.org/meta-schemas/core.yaml# > + > +title: Synopsys DWC PCIe RP/EP controller > + > +maintainers: > + - Jingoo Han <jingoohan1@xxxxxxxxx> > + - Gustavo Pimentel <gustavo.pimentel@xxxxxxxxxxxx> > + > +properties: > + reg: > + description: > + DWC PCIe CSR space is normally accessed over the dedicated Data Bus > + Interface - DBI. In accordance with the reference manual the register > + configuration space belongs to the Configuration-Dependent Module (CDM) > + and is split up into several sub-parts Standard PCIe configuration > + space, Port Logic Registers (PL), Shadow Config-space Registers, > + iATU/eDMA registers. The particular sub-space is selected by the > + CDM/ELBI (dbi_cs) and CS2 (dbi_cs2) signals (selector bits). Such > + configuration provides a flexible interface for the system engineers to > + either map the particular space at a desired MMIO address or just leave > + them in a contiguous memory space if pure Native or AXI Bridge DBI access > + is selected. Note the PCIe CFG-space, PL and Shadow registers are > + specific to each activated function, while the rest of the sub-spaces > + are common for all of them (if there are more than one). > + minItems: 2 > + maxItems: 6 > + > + interrupts: > + description: > + There are two main sub-blocks which are normally capable of > + generating interrupts. It's System Information Interface and MSI > + interface. While the former one has some common for the Host and > + End-point controllers IRQ-signals, the later interface is obviously > + Root Complex specific since it's responsible for the incoming MSI > + messages signalling. The System Information IRQ signals are mainly > + responsible for reporting the generic PCIe hierarchy and Root > + Complex events like VPD IO request, general AER, PME, Hot-plug, link > + bandwidth change, link equalization request, INTx asserted/deasserted > + Message detection, embedded DMA Tx/Rx/Error. > + minItems: 1 > + maxItems: 26 > + > + clocks: > + description: > + DWC PCIe reference manual explicitly defines a set of the clocks required > + to get the controller working correctly. In general all of them can > + be divided into two groups':' application and core clocks. Note the > + platforms may have some of the clock sources unspecified in case if the > + corresponding domains are fed up from a common clock source. > + minItems: 1 > + maxItems: 7 > + > + resets: > + description: > + DWC PCIe reference manual explicitly defines a set of the reset > + signals required to be de-asserted to properly activate the controller > + sub-parts. All of these signals can be divided into two sub-groups':' > + application and core resets with respect to the main sub-domains they > + are supposed to reset. Note the platforms may have some of these signals > + unspecified in case if they are automatically handled or aggregated into > + a comprehensive control module. > + minItems: 1 > + maxItems: 10 > + > + reset-gpio: > + deprecated: true > + description: > + Reference to the GPIO-controlled PERST# signal. It is used to reset all > + the peripheral devices available on the PCIe bus. > + maxItems: 1 > + > + reset-gpios: > + description: > + Reference to the GPIO-controlled PERST# signal. It is used to reset all > + the peripheral devices available on the PCIe bus. > + maxItems: 1 > + > + phys: > + description: > + There can be up to number of possible lanes PHYs specified. > + Obviously each specified PHY is supposed to be able to work in the > + PCIe mode with a speed implied by the DWC PCIe controller it is > + attached to. > + minItems: 1 > + maxItems: 16 > + > + phy-names: > + minItems: 1 > + maxItems: 16 > + items: > + pattern: '^pcie([0-9]+|-?phy)?$' > + > + num-lanes: > + maximum: 16 > + > + max-link-speed: > + maximum: 4 > + > + num-ob-windows: > + $ref: /schemas/types.yaml#/definitions/uint32 > + deprecated: true > + description: > + Number of outbound address translation windows. This parameter can be > + auto-detected based on the iATU memory writability. So there is no > + point in having a dedicated DT-property for it. > + maximum: 256 > + > + num-ib-windows: > + $ref: /schemas/types.yaml#/definitions/uint32 > + deprecated: true > + description: > + Number of inbound address translation windows. In the same way as > + for the outbound AT windows, this parameter can be auto-detected based > + on the iATU memory writability. There is no point having a dedicated > + DT-property for it either. > + maximum: 256 > + > + num-viewport: > + $ref: /schemas/types.yaml#/definitions/uint32 > + deprecated: true > + description: > + Number of outbound view ports configured in hardware. It's the same as > + the number of outbound AT windows. > + maximum: 256 > + > + snps,enable-cdm-check: > + $ref: /schemas/types.yaml#/definitions/flag > + description: > + Enable automatic checking of CDM (Configuration Dependent Module) > + registers for data corruption. CDM registers include standard PCIe > + configuration space registers, Port Logic registers, DMA and iATU > + registers. This feature has been available since DWC PCIe v4.80a. > + > +additionalProperties: true > + > +$defs: > + reg-names: > + description: > + CSR space names common for the DWC PCIe Root Port and End-point > + controllers. > + oneOf: > + - description: > + Basic DWC PCIe controller configuration-space accessible over > + the DBI interface. This memory space is either activated with > + the CDM/ELBI = 0 and CS2 = 0 or is a contiguous memory region > + with all spaces. Note iATU/eDMA CSRs are indirectly accessible > + via the PL viewports on the DWC PCIe controllers older than > + v4.80a. > + const: dbi This passes only for 'reg-names = "dbi";' > + - description: > + Shadow DWC PCIe config-space registers. This space is selected > + by setting CDM/ELBI = 0 and CS2 = 1. This is an intermix of > + the PCI-SIG PCIe CFG-space with the shadow registers for some > + PCI Header space, PCI Standard and Extended Structures. It's > + mainly relevant for the end-point controller configuration, > + but still there are some shadow registers available for the > + Root Port mode too. > + const: dbi2 This passes only for 'reg-names = "dbi2";' > + - description: > + External Local Bus registers. It's an application-dependent > + registers normally defined by the platform engineers, which > + are selected by setting CDM/ELBI = 1 and CS2 = 0. > + enum: [ elbi, appl, app ] This passes only for 'reg-names = "elbi", "appl", "app";' See the problem? Replacing the 'oneOf' above with 'items' is what you want. But then the schema will not allow any missing entries either. DBI2 is optional for example. There is no way in json-schema to define a list of ordered values(string) once and say some entries are optional which I think is what you are trying to do here. > + - description: > + iATU/eDMA registers common for all device functions. It's an > + unrolled memory space with the internal Address Translation > + Unit and Enhanced DMA, which is selected by setting CDM/ELBI = 1 > + and CS2 = 1. For IP-core releases prior v4.80a, these registers > + have been programmed via an indirect addressing scheme using a > + set of viewport CSRs mapped into the PL space. Note iATU is > + normally mapped to the 0x0 address of this region, while eDMA > + is available at 0x80000 base address. > + enum: [ atu, atu_dma ] > + - description: > + Outbound iATU-available memory-region which usage scenario > + depends on the DWC PCIe controller being either Root Port or > + End-point. If it's Root Port then the register space shall > + have the "config" name and it will be used to access the > + peripheral PCIe devices configuration space. If it's PCIe > + end-point controller, then the region shall be named as > + "addr_space" and it will be used to generate various traffic > + on the PCIe bus hierarchy. It's usage scenario depends on the > + end-point functionality, for instance it can be used to create > + MSI(X) messages. > + enum: [ config, addr_space ] So 'addr_space' is now valid for host mode? (Really, for DW blocks with iATU, this should have been the whole memory space and the driver could size the config space itself. (IOW, the config region is configuration rather than h/w description.) > + - description: > + PHY/PCS configuration registers. Some platforms can have the > + PCS and PHY CSRs accessible over a dedicated memory mapped > + region, but mainly these registers are indirectly accessible > + either by means of the embedded PHY viewport schema or by some > + platform-specific method. > + enum: [ link, phy ] These should not be in any new users as the phy should be separate. > + > + interrupt-names: > + description: > + IRQ signal names common for the DWC PCIe Root Port and End-point > + controllers. > + oneOf: > + - description: > + Controller request to read or write virtual product data > + from/to the VPD capability registers. > + const: vpd > + - description: > + Link Equalization Request flag is set in the Link Status 2 > + register (applicable if the corresponding IRQ is enabled in > + the Link Control 3 register). > + const: l_eq > + - description: > + Indicates that the eDMA Tx/Rx transfer is complete or that an > + error has occurred on the corresponding channel. eDMA can have > + eight Tx (Write) and Rx (Read) eDMA channels thus supporting up > + to 16 IRQ signals all together. Write eDMA channels shall go > + first in the ordered row as per default edma_int[*] bus setup. > + pattern: '^dma([0-9]|1[0-5])?$' > + - description: > + PCIe protocol correctable error or a Data Path protection > + correctable error is detected by the automotive/safety > + feature. > + const: sft_ce > + - description: > + Indicates that the internal safety mechanism detected and > + uncorrectable error. > + const: sft_ue This says there is only a single interrupt entry. Same for the other $defs. Rob
