Re: [PATCH v2 3/4] clocksource/drivers/exynos_mct: Support local-timer-index property

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Krzysztof,

On 11.03.2022 13:51, Krzysztof Kozlowski wrote:
> On 11/03/2022 12:35, Vincent Whitchurch wrote:
>> On Tue, Mar 08, 2022 at 03:57:55PM +0100, Krzysztof Kozlowski wrote:
>>> On 08/03/2022 15:24, Vincent Whitchurch wrote:
>>>> diff --git a/drivers/clocksource/exynos_mct.c b/drivers/clocksource/exynos_mct.c
>>>> index f29c812b70c9..5f8b516614eb 100644
>>>> --- a/drivers/clocksource/exynos_mct.c
>>>> +++ b/drivers/clocksource/exynos_mct.c
>>>> @@ -33,7 +33,7 @@
>>>>   #define EXYNOS4_MCT_G_INT_ENB		EXYNOS4_MCTREG(0x248)
>>>>   #define EXYNOS4_MCT_G_WSTAT		EXYNOS4_MCTREG(0x24C)
>>>>   #define _EXYNOS4_MCT_L_BASE		EXYNOS4_MCTREG(0x300)
>>>> -#define EXYNOS4_MCT_L_BASE(x)		(_EXYNOS4_MCT_L_BASE + (0x100 * x))
>>>> +#define EXYNOS4_MCT_L_BASE(x)		(_EXYNOS4_MCT_L_BASE + (0x100 * (x)))
>>>>   #define EXYNOS4_MCT_L_MASK		(0xffffff00)
>>>>   
>>>>   #define MCT_L_TCNTB_OFFSET		(0x00)
>>>> @@ -75,6 +75,7 @@ enum {
>>>>   static void __iomem *reg_base;
>>>>   static unsigned long clk_rate;
>>>>   static unsigned int mct_int_type;
>>>> +static unsigned int mct_local_idx;
>>> No more static variables. This was wrong design, happens, but let's not
>>> grow the list.
>>>
>>> I propose to conditionally (depending on property samsung,frc-shared)
>>> assign .resume callback to NULL or exynos4_frc_resume. The init can
>>> receive an argument whether to call frc_start().
>> Could we just add the skip-write-register-if-already-started change in
>> exynos4_mct_frc_start() uncondtionally?  Perhaps it could be in a
>> separate patch too?  I was probably being over-cautious when I did it
>> conditionally on mct_local_idx.  Doing it uncondtionally would make it
>> easier to remove the global variable.
>>
>> On my system the FRC is actually started long before Linux, and I assume
>> it's similar on other chips.
> +Cc Marek,
>
> Maybe we could skip it, I don't know. It could be enabled by early boot
> code or by trusted firmware. This would require more testing, on few
> different platforms.
>
> On my Exynos5422 HC1 board the MCT is not running upon boot. The
> EXYNOS4_MCT_G_TCON starts with a reset value (0x0).
>
>>>>   static int mct_irqs[MCT_NR_IRQS];
>>>>   
>>>>   struct mct_clock_event_device {
>>>> @@ -157,6 +158,17 @@ static void exynos4_mct_frc_start(void)
>>>>   	u32 reg;
>>>>   
>>>>   	reg = readl_relaxed(reg_base + EXYNOS4_MCT_G_TCON);
>>>> +
>>>> +	/*
>>>> +	 * If the FRC is already running, we don't need to start it again.  We
>>>> +	 * could probably just do this on all systems, but, to avoid any risk
>>>> +	 * for regressions, we only do it on systems where it's absolutely
>>>> +	 * necessary (i.e., on systems where writes to the global registers
>>>> +	 * need to be avoided).
>>>> +	 */
>>>> +	if (mct_local_idx && (reg & MCT_G_TCON_START))
>>> This contradicts your intentions in commit #2 msg, where you described
>>> that A53 will be started first.
>> Yes, you're right.  The case of the FRC not being running when the A5
>> starts up is only ever hit in our simulation environment where we are
>> able to start Linux on the A5 directly, without having to go via the
>> A53.
>>
>>> 1. If A53 is always started first, is it possible to be here from A5?
>>> 2. If above is possible, how do you handle locking? For example:
>>> a. A53 started with some delay, entered exynos4_mct_frc_start() pass
>>> this check;
>>> b. A5 gets to exynos4_mct_frc_start(), check is still false, so A5
>>> enables the FRC,
>>> c. A53 also enables the FRC.
>> The A5 is normally started from Linux on the A53 (using the remoteproc
>> framework).  This is long after exynos4_mct_frc_start() has been called
>> on the A53.
> If it is 100% like this, let's make it explicit - if it is A53 (lack of
> dedicated property), let's start it. If it A5 (property present), skip it.
>
> Let's wait for Marek thoughts, he was digging the MCT a lot.


Right, I've played a bit with MCT on some older Exynos SoCs (ARM 32bit 
based and even Exynos5433) and it looked that none of it enabled MCT FRC 
timer in their proprietary firmware. I've even proposed a patch for this 
once ([1]), but such approach has been rejected. I think that calling 
exynos4_mct_frc_start() unconditionally won't hurt.

[1] https://lore.kernel.org/all/20181018095708.1527-5-m.szyprowski@xxxxxxxxxxx/

Best regards
-- 
Marek Szyprowski, PhD
Samsung R&D Institute Poland




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux