This device is a SPI based device from TI.
It is a 3 Gbps HD/SD SDI Dual Output Low Power
Extended Reach Adaptive Cable Equalizer.
LMH0395 enables the use of up to two outputs.
These can be configured using DT.
Controls should be accessible from userspace too...
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@xxxxxxxxxxx>
---
.../devicetree/bindings/media/spi/lmh0395.txt | 44 +++
MAINTAINERS | 6 +
drivers/media/spi/Kconfig | 14 +
drivers/media/spi/Makefile | 1 +
drivers/media/spi/lmh0395.c | 355 +++++++++++++++++++++
5 files changed, 420 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/spi/lmh0395.txt
create mode 100644 drivers/media/spi/Kconfig
create mode 100644 drivers/media/spi/Makefile
create mode 100644 drivers/media/spi/lmh0395.c
diff --git a/Documentation/devicetree/bindings/media/spi/lmh0395.txt b/Documentation/devicetree/bindings/media/spi/lmh0395.txt
new file mode 100644
index 0000000..0a640a4
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/spi/lmh0395.txt
@@ -0,0 +1,44 @@
+* Texas Instruments lmh0395 3G HD/SD SDI equalizer
+
+The LMH0395 3 Gbps HD/SD SDI Dual Output Low Power Extended Reach Adaptive
+Cable Equalizer is designed to equalize data transmitted over cable (or any
+media with similar dispersive loss characteristics).
+The equalizer operates over a wide range of data rates from 125 Mbps to 2.97 Gbps
+and supports SMPTE 424M, SMPTE 292M, SMPTE344M, SMPTE 259M, and DVB-ASI standards.
+
+Required Properties :
+- compatible: Must be "ti,lmh0395"
+
+The device node must contain one 'port' child node per device input and output
+port, in accordance with the video interface bindings defined in
+Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
+are numbered as follows.
+
+ Port LMH0395
+------------------------------------------------------------
+ SDI input 0
+ SDI output 1,2
+
+Example:
+
+ecspi@02010000 {
+ ...
+ ...
+
+ lmh0395@1 {
+ compatible = "ti,lmh0395";
+ reg = <1>;
+ spi-max-frequency = <20000000>;
+ ports {
+ port@0 {
+ reg = <0>;
+ sdi0_in: endpoint {};
+ };
+ port@1 {
+ reg=<1>;
+ sdi0_out0: endpoint {};
+ };
+ };
+ };
+ ...
+};
diff --git a/MAINTAINERS b/MAINTAINERS
index cf24bb5..ca42b9e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -9141,6 +9141,12 @@ S: Maintained
F: sound/soc/codecs/lm49453*
F: sound/soc/codecs/isabelle*
+TI LMH0395 DRIVER
+M: Jean-Michel Hautbois <jean-michel.hautbois@xxxxxxxxxxx>
+L: linux-media@xxxxxxxxxxxxxxx
+S: Maintained
+F: drivers/media/spi/lmh0395*
+
TI LP855x BACKLIGHT DRIVER
M: Milo Kim <milo.kim@xxxxxx>
S: Maintained
diff --git a/drivers/media/spi/Kconfig b/drivers/media/spi/Kconfig
new file mode 100644
index 0000000..291e7ea
--- /dev/null
+++ b/drivers/media/spi/Kconfig
@@ -0,0 +1,14 @@
+if VIDEO_V4L2
+
+config VIDEO_LMH0395
+ tristate "LMH0395 equalizer"
+ depends on VIDEO_V4L2 && SPI && MEDIA_CONTROLLER
+ ---help---
+ Support for TI LMH0395 3G HD/SD SDI Dual Output Low Power
+ Extended Reach Adaptive Cable Equalizer.
+
+ To compile this driver as a module, choose M here: the
+ module will be called lmh0395.
+
+
+endif
diff --git a/drivers/media/spi/Makefile b/drivers/media/spi/Makefile
new file mode 100644
index 0000000..6c587e5
--- /dev/null
+++ b/drivers/media/spi/Makefile
@@ -0,0 +1 @@
+obj-$(CONFIG_VIDEO_LMH0395) += lmh0395.o
diff --git a/drivers/media/spi/lmh0395.c b/drivers/media/spi/lmh0395.c
new file mode 100644
index 0000000..ecf8f83
--- /dev/null
+++ b/drivers/media/spi/lmh0395.c
@@ -0,0 +1,355 @@
+/*
+ * LMH0395 SPI driver.
+ * Copyright (C) 2014 Jean-Michel Hautbois
+ *
+ * 3G HD/SD SDI Dual Output Low Power Extended Reach Adaptive Cable Equalizer
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/ioctl.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/types.h>
+#include <linux/slab.h>
+#include <linux/uaccess.h>
+#include <linux/spi/spi.h>
+#include <linux/videodev2.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-of.h>
+
+static int debug;
+module_param(debug, int, 0644);
+MODULE_PARM_DESC(debug, "debug level (0-1)");
+
+#define LMH0395_SPI_CMD_WRITE 0x00
+#define LMH0395_SPI_CMD_READ 0x80
+
+/* Registers of LMH0395 */
+#define LMH0395_GENERAL_CTRL 0x00
+#define LMH0395_OUTPUT_DRIVER 0x01
+#define LMH0395_LAUNCH_AMP_CTRL 0x02
+#define LMH0395_MUTE_REF 0x03
+#define LMH0395_DEVICE_ID 0x04
+#define LMH0395_RATE_INDICATOR 0x05
+#define LMH0395_CABLE_LENGTH_INDICATOR 0x06
+#define LMH0395_LAUNCH_AMP_INDICATION 0x07
+
+/* This is a one input, dual output device */
+#define LMH0395_SDI_INPUT 0
+#define LMH0395_SDI_OUT0 1
+#define LMH0395_SDI_OUT1 2
+
+#define LMH0395_PADS_NUM 3
+
+/* Register LMH0395_MUTE_REF bits [7:6] */
+enum lmh0395_output_type {
+ LMH0395_OUTPUT_TYPE_NONE,
+ LMH0395_OUTPUT_TYPE_SDO0,
+ LMH0395_OUTPUT_TYPE_SDO1,
+ LMH0395_OUTPUT_TYPE_BOTH
+};
+
+static const char * const output_strs[] = {
+ "No Output Driver",
+ "Output Driver 0",
+ "Output Driver 1",
+ "Output Driver 0+1",
+};
+
+
+/* spi implementation */
+
+static int lmh0395_spi_write(struct spi_device *spi, u8 reg, u8 data)
+{
+ int err;
+ u8 cmd[2];
+
+ cmd[0] = LMH0395_SPI_CMD_WRITE | reg;
+ cmd[1] = data;
+
+ err = spi_write(spi, cmd, 2);
+ if (err < 0) {
+ dev_err(&spi->dev, "SPI failed to select reg\n");
+ return err;
+ }
+
+ return err;
+}
+
+static int lmh0395_spi_read(struct spi_device *spi, u8 reg, u8 *data)
+{
+ int err;
+ u8 cmd[2];
+ u8 read_data[2];
+
+ cmd[0] = LMH0395_SPI_CMD_READ | reg;
+ cmd[1] = 0xFF;
+
+ err = spi_write(spi, cmd, 2);
+ if (err < 0) {
+ dev_err(&spi->dev, "SPI failed to select reg\n");
+ return err;
+ }
+
+ err = spi_read(spi, read_data, 2);
+ if (err < 0) {
+ dev_err(&spi->dev, "SPI failed to read reg\n");
+ return err;
+ }
+ /* The first 8 bits is the adress used, drop it */
+ *data = read_data[1];
+
+ return err;
+}
+
+struct lmh0395_state {
+ struct v4l2_subdev sd;
+ struct media_pad pads[LMH0395_PADS_NUM];
+ enum lmh0395_output_type output_type;
+};
+
+static inline struct lmh0395_state *to_state(struct v4l2_subdev *sd)
+{
+ return container_of(sd, struct lmh0395_state, sd);
+}
+
+static int lmh0395_set_output_type(struct v4l2_subdev *sd, u32 output)
+{
+ struct lmh0395_state *state = to_state(sd);
+ struct spi_device *spi = v4l2_get_subdevdata(sd);
+ u8 muteref_reg;
+
+ switch (output) {
+ case LMH0395_OUTPUT_TYPE_SDO0:
+ lmh0395_spi_read(spi, LMH0395_MUTE_REF, &muteref_reg);
+ muteref_reg |= 0x01 << 6;
+ break;
+ case LMH0395_OUTPUT_TYPE_SDO1:
+ lmh0395_spi_read(spi, LMH0395_MUTE_REF, &muteref_reg);
+ muteref_reg |= 0x10 << 6;
+ break;
+ case LMH0395_OUTPUT_TYPE_BOTH:
+ lmh0395_spi_read(spi, LMH0395_MUTE_REF, &muteref_reg);
+ muteref_reg |= 0x11 << 6;
+ break;
+ case LMH0395_OUTPUT_TYPE_NONE:
+ lmh0395_spi_read(spi, LMH0395_MUTE_REF, &muteref_reg);
+ muteref_reg |= 0x0 << 6;
+ break;
+ default:
+ return -EINVAL;
+ }
+ v4l2_dbg(1, debug, sd, "Selecting %s output type\n",
+ output_strs[output]);
+
+ lmh0395_spi_write(spi, LMH0395_MUTE_REF, muteref_reg);
+ state->output_type = output;
+ return 0;
+
+}
+
+static int lmh0395_get_rate(struct v4l2_subdev *sd, u8 *rate)
+{
+ struct spi_device *spi = v4l2_get_subdevdata(sd);
+ int err;
+ u8 ctrl;
+
+ err = lmh0395_spi_read(spi, LMH0395_RATE_INDICATOR, &ctrl);
+ if (err < 0)
+ return err;
+
+ *rate = ctrl & 0x20;
+ v4l2_dbg(1, debug, sd, "Rate : %s\n", (ctrl & 0x20)?"3G/HD":"SD");
+ return 0;
+}
+
+static int lmh0395_get_cable_length(struct v4l2_subdev *sd, u8 rate)
+{
+ struct spi_device *spi = v4l2_get_subdevdata(sd);
+ u8 length;
+ u8 cli;
+ int err;
+
+ err = lmh0395_spi_read(spi, LMH0395_CABLE_LENGTH_INDICATOR, &cli);
+ if (err < 0)
+ return err;
+
+ /* The cable length indicator (CLI) provides an indication of the
+ * length of the cable attached to input. CLI is accessible via bits
+ * [7:0] of SPI register 06h.
+ * The 8-bit setting ranges in decimal value from 0 to 247
+ * ("00000000" to "11110111" binary), corresponding to 0 to 400m of
+ * Belden 1694A cable.
+ * For 3G and HD input, CLI is 1.25m per step.
+ * For SD input, CLI is 1.25m per step, less 20m, from 0 to 191 decimal
+ * and 3.5m per step from 192 to 247 decimal.
+ */
+
+ length = cli*5/4;
+ if (rate == 0) {
+ if (cli <= 191)
+ length -= 20;
+ else
+ length = ((191*5/4)-20) + ((cli-191)*7/2);
+
+ }
+ v4l2_dbg(1, debug, sd, "Length estimated (BELDEN 1694A cables) : %dm\n",
+ length);
+ return 0;
+}
+
+static int lmh0395_get_control(struct v4l2_subdev *sd)
+{
+ int err;
+ struct spi_device *spi = v4l2_get_subdevdata(sd);
+ u8 ctrl;
+ u8 rate;
+
+ err = lmh0395_spi_read(spi, LMH0395_GENERAL_CTRL, &ctrl);
+ if (err < 0)
+ return err;
+
+ if (ctrl & 0x80) {
+ v4l2_dbg(1, debug, sd, "Carrier detected\n");
+ lmh0395_get_rate(sd, &rate);
+ lmh0395_get_cable_length(sd, rate);
+ }
+ return 0;
+}
+
+static int lmh0395_s_routing(struct v4l2_subdev *sd, u32 input, u32 output,
+ u32 config)
+{
+ struct lmh0395_state *state = to_state(sd);
+ int err = 0;
+
+ if (state->output_type != output)
+ err = lmh0395_set_output_type(sd, output);
+
+ return err;
+}
+
+static const struct v4l2_subdev_video_ops lmh0395_video_ops = {
+ .s_routing = lmh0395_s_routing,
+};
+
+static const struct v4l2_subdev_ops lmh0395_ops = {
+ .video = &lmh0395_video_ops,
+};
+
+static const struct spi_device_id lmh0395_id[] = {
+ { "lmh0395", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(spi, lmh0395_id);
+
+#if IS_ENABLED(CONFIG_OF)
+static const struct of_device_id lmh0395_of_match[] = {
+ {.compatible = "ti,lmh0395", },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(of, lmh0395_of_match);
+#endif
+
+static int lmh0395_probe(struct spi_device *spi)
+{
+ u8 device_id;
+
+ struct lmh0395_state *state;
+ struct v4l2_subdev *sd;
+ int err;
+
+ err = lmh0395_spi_read(spi, LMH0395_DEVICE_ID, &device_id);
+ if (err < 0)
+ return err;
+
+ dev_dbg(&spi->dev, "device_id 0x%x\n", device_id);
+
+ /* Now that the device is here, let's init V4L2 */
+ state = devm_kzalloc(&spi->dev, sizeof(*state), GFP_KERNEL);
+ if (!state)
+ return -ENOMEM;
+
+ sd = &state->sd;
+ v4l2_spi_subdev_init(sd, spi, &lmh0395_ops);
+ state->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+ state->pads[LMH0395_SDI_INPUT].flags = MEDIA_PAD_FL_SINK;
+ state->pads[LMH0395_SDI_OUT0].flags = MEDIA_PAD_FL_SOURCE;
+ state->pads[LMH0395_SDI_OUT1].flags = MEDIA_PAD_FL_SOURCE;
+ err = media_entity_init(&sd->entity, LMH0395_PADS_NUM, state->pads, 0);
+ if (err)
+ return err;
+
+ err = v4l2_async_register_subdev(sd);
+ if (err < 0) {
+ media_entity_cleanup(&sd->entity);
+ return err;
+ }
+
+ v4l2_dbg(1, debug, sd, "Configuring equalizer\n");
+ lmh0395_get_control(sd);
+ /* Default is no output */
+ lmh0395_set_output_type(sd, LMH0395_OUTPUT_TYPE_NONE);
+
+ if (IS_ENABLED(CONFIG_OF) && spi->dev.of_node) {
+ const struct of_device_id *oid;
+ struct device_node *n;
+ struct of_endpoint ep;
+
+ oid = of_match_node(lmh0395_of_match, spi->dev.of_node);
+ n = NULL;
+ while ((n = of_graph_get_next_endpoint(spi->dev.of_node, n))
+ != NULL) {
+ of_graph_parse_endpoint(n, &ep);
+ dev_dbg(&spi->dev, "endpoint %d on port %d\n",
+ ep.id, ep.port);
+ /* port 1 => SDO0 */
+ if (ep.port >= 1)
+ lmh0395_set_output_type(sd, ep.port);
+ of_node_put(n);
+ }
+ } else {
+ dev_dbg(&spi->dev, "No DT configuration\n");
+ }
+
+ dev_dbg(&spi->dev, "device probed\n");
+
+ return 0;
+}
+
+static int lmh0395_remove(struct spi_device *spi)
+{
+ struct v4l2_subdev *sd = spi_get_drvdata(spi);
+
+ v4l2_async_unregister_subdev(sd);
+ media_entity_cleanup(&sd->entity);
+ return 0;
+}
+
+
+static struct spi_driver lmh0395_driver = {
+ .driver = {
+ .of_match_table = of_match_ptr(lmh0395_of_match),
+ .name = "lmh0395",
+ .owner = THIS_MODULE,
+ },
+ .probe = lmh0395_probe,
+ .remove = lmh0395_remove,
+ .id_table = lmh0395_id,
+};
+
+module_spi_driver(lmh0395_driver);
+
+MODULE_DESCRIPTION("spi device driver for LMH0395 equalizer");
+MODULE_AUTHOR("Jean-Michel Hautbois");
+MODULE_LICENSE("GPL");
--
2.0.4
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
