Re: [PATCH 2/3] phy: phy-stih407-usb: Add dt documentation for USB picophy found on stih407 SoC family

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




Hi,

On Wednesday 03 September 2014 03:57 PM, Peter Griffin wrote:
> This patch adds the dt documentation for the usb picophy found on stih407 SoC family
> available from STMicroelectronics.
> 
> Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@xxxxxx>
> Signed-off-by: Peter Griffin <peter.griffin@xxxxxxxxxx>
> ---
>  .../devicetree/bindings/phy/phy-stih407-usb.txt    | 37 ++++++++++++++++++++++
>  1 file changed, 37 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
> 
> diff --git a/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
> new file mode 100644
> index 0000000..650d346
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/phy-stih407-usb.txt
> @@ -0,0 +1,37 @@
> +ST STiH407 USB-PHY controller
> +
> +This file documents the dt bindings for the picoPHY driver which is the PHY for both USB2 and USB3 host controllers
> +controllers available on STiH407 SoC families.
> +
> +On STiH410, we have to use the DWC3 port#2 with a picoPHY to manage USB2
> +devices. The USB2 Controller will use the ports #0 and #1.
> +
> +This is to document the DT parameters to be passed from the blob in that case.
> +
> +Required properties:
> +- compatible		: should be "st,stih407-usb2-phy"

If STiH410 also uses the same driver then you should add a new compatibility
value for it.
> +- reg			: contain the offset and length of the system configuration registers
> +			  used as glue logic to control & parameter phy
> +- reg-names		: the names of the system configuration registers in "reg", should be "param" and "reg"
> +- st,syscfg		: sysconfig register to manage phy parameter at driver level
> +- resets		: list of phandle and reset specifier pairs. There should be two entries, one
> +			  for the whole phy and one for the port
> +- reset-names		: list of reset signal names. Should be "global" and "port"
> +See: Documentation/devicetree/bindings/reset/st,sti-powerdown.txt
> +See: Documentation/devicetree/bindings/reset/reset.txt
> +
> +Example:
> +
> +usb2_picophy0: usbpicophy@0 {
usbpicophy@f8 since you have a reg property ;-)

> +	compatible	= "st,stih407-usb2-phy";
> +	reg		= <0xf8 0x04>,	/* syscfg 5062 */
> +			  <0xf4 0x04>;	/* syscfg 5061 */
> +	reg-names	= "param",
> +			  "ctrl";
> +			  #phy-cells = <0>;

alignment seems to have gone wrong here.

Thanks
Kishon
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]
  Powered by Linux