Add all the usart nodes for the flexcom block. There was already
an usart node for the flexcom3 block. But it missed the DMA
channels. Although the DMA channels are specified, DMA is not
enabled by default because break detection doesn't work with DMA.
Keep the nodes disabled by default.
Signed-off-by: Michael Walle <michael@xxxxxxxx>
---
arch/arm/boot/dts/lan966x.dtsi | 55 ++++++++++++++++++++++++++++++++++
1 file changed, 55 insertions(+)
diff --git a/arch/arm/boot/dts/lan966x.dtsi b/arch/arm/boot/dts/lan966x.dtsi
index a7d46a2ca058..bea69b6d2749 100644
--- a/arch/arm/boot/dts/lan966x.dtsi
+++ b/arch/arm/boot/dts/lan966x.dtsi
@@ -92,6 +92,19 @@ flx0: flexcom@e0040000 {
#size-cells = <1>;
ranges = <0x0 0xe0040000 0x800>;
status = "disabled";
+
+ usart0: serial@200 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(3)>,
+ <&dma0 AT91_XDMAC_DT_PERID(2)>;
+ dma-names = "tx", "rx";
+ clocks = <&nic_clk>;
+ clock-names = "usart";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
};
flx1: flexcom@e0044000 {
@@ -102,6 +115,19 @@ flx1: flexcom@e0044000 {
#size-cells = <1>;
ranges = <0x0 0xe0044000 0x800>;
status = "disabled";
+
+ usart1: serial@200 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(5)>,
+ <&dma0 AT91_XDMAC_DT_PERID(4)>;
+ dma-names = "tx", "rx";
+ clocks = <&nic_clk>;
+ clock-names = "usart";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
};
trng: rng@e0048000 {
@@ -129,6 +155,19 @@ flx2: flexcom@e0060000 {
#size-cells = <1>;
ranges = <0x0 0xe0060000 0x800>;
status = "disabled";
+
+ usart2: serial@200 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(7)>,
+ <&dma0 AT91_XDMAC_DT_PERID(6)>;
+ dma-names = "tx", "rx";
+ clocks = <&nic_clk>;
+ clock-names = "usart";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
};
flx3: flexcom@e0064000 {
@@ -144,6 +183,9 @@ usart3: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(9)>,
+ <&dma0 AT91_XDMAC_DT_PERID(8)>;
+ dma-names = "tx", "rx";
clocks = <&nic_clk>;
clock-names = "usart";
atmel,fifo-size = <32>;
@@ -178,6 +220,19 @@ flx4: flexcom@e0070000 {
#size-cells = <1>;
ranges = <0x0 0xe0070000 0x800>;
status = "disabled";
+
+ usart4: serial@200 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>;
+ dmas = <&dma0 AT91_XDMAC_DT_PERID(11)>,
+ <&dma0 AT91_XDMAC_DT_PERID(10)>;
+ dma-names = "tx", "rx";
+ clocks = <&nic_clk>;
+ clock-names = "usart";
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
};
timer0: timer@e008c000 {
--
2.30.2
