On Sat, Feb 19, 2022 at 07:08:34PM +0000, Jonathan McDowell wrote:
> On Fri, Feb 18, 2022 at 02:11:59PM +0000, Jonathan McDowell wrote:
> > On Fri, Feb 18, 2022 at 01:29:54AM +0100, Ansuel Smith wrote:
> > > Mdio0_pins are now declared in ipq8064 dtsi. Usb phy are enabled by
> > > default.
> ...
> > > - mdio0_pins: mdio0_pins {
> > > - mux {
> > > - pins = "gpio0", "gpio1";
> > > - function = "gpio";
> > > - drive-strength = <8>;
> > > - bias-disable;
> > > - };
> > > - };
> > > -
> >
> > This sets the pins to "gpio". Your earlier patch sets them to "mdio", so
> > removing this will break MDIO0 on the RB3011. It's likely that your
> > fixes for MDIO/QCA8K mean that the RB3011 can be switch to use the MDIO
> > driver rather than mdio-gpio, but that will need tested and this change
> > alone will definitely break things.
>
> I tried the below patch to switch the RB3011 to the IPQ8064 MDIO driver
> (based on qcom,ipq8064-mdio.yaml) and get:
>
> [ 1.270310] qca8k 37000000.mdio-mii:10: Switch id detected 0 but expected 13
>
> and none of the ports on that associated switch come up. Kernel is
> 5.15.23 rather than latest, but there are no updates to mdio-ipq8064.c
> in later kernels than I can see and none of the qca8k changes seem
> relevant. Is there something else I'm missing?
>
I encounter an error like that when the MDIO_MASTER_EN was set to 1.
Wonder if we should trigger a switch reset or a reset of the
MDIO_MASTER_EN before probing the switch? (this is currently done after
any phy read/write)
But it's strange... Wonder if the dedicated mdio can't work on this
device with 2 switch attached?
>
> diff --git a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
> index c3e3070702f9..0cafee65ca22 100644
> --- a/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
> +++ b/arch/arm/boot/dts/qcom-ipq8064-rb3011.dts
> @@ -24,13 +24,13 @@ memory@42000000 {
> device_type = "memory";
> };
>
> - mdio0: mdio-0 {
> + mdio0: mdio@37000000 {
> status = "okay";
> - compatible = "virtual,mdio-gpio";
> - gpios = <&qcom_pinmux 1 GPIO_ACTIVE_HIGH>,
> - <&qcom_pinmux 0 GPIO_ACTIVE_HIGH>;
> + compatible = "qcom,ipq8064-mdio";
> #address-cells = <1>;
> #size-cells = <0>;
> + reg = <0x37000000 0x200000>;
> + clocks = <&gcc GMAC_CORE1_CLK>;
>
> pinctrl-0 = <&mdio0_pins>;
> pinctrl-names = "default";
> @@ -318,7 +318,7 @@ mux {
> mdio0_pins: mdio0_pins {
> mux {
> pins = "gpio0", "gpio1";
> - function = "gpio";
> + function = "mdio";
> drive-strength = <8>;
> bias-disable;
> };
>
> J.
>
> --
> /-\ | Shall I call the United Nations?
> |@/ Debian GNU/Linux Developer |
> \- |
--
Ansuel
