From: Dave Gerlach <d-gerlach@xxxxxx>
AM43xx support isolation of the IOs so that control is taken
from the peripheral they are connected to and overridden by values
present in the CTRL_CONF_* registers for the pad in the control module.
The actual toggling happens from the wkup_m3, so use a DT property from
thea wkup_m3_ipc node to allow the PM code to communicate the necessity
for placing the IOs into isolation to the firmware.
Signed-off-by: Dave Gerlach <d-gerlach@xxxxxx>
Signed-off-by: Keerthy <j-keerthy@xxxxxx>
Signed-off-by: Drew Fustini <dfustini@xxxxxxxxxxxx>
---
drivers/soc/ti/wkup_m3_ipc.c | 14 ++++++++++++--
include/linux/wkup_m3_ipc.h | 1 +
2 files changed, 13 insertions(+), 2 deletions(-)
diff --git a/drivers/soc/ti/wkup_m3_ipc.c b/drivers/soc/ti/wkup_m3_ipc.c
index 974b4118a893..e7ae942b7014 100644
--- a/drivers/soc/ti/wkup_m3_ipc.c
+++ b/drivers/soc/ti/wkup_m3_ipc.c
@@ -46,6 +46,8 @@
#define IPC_VTT_STAT_MASK (0x1 << 3)
#define IPC_VTT_GPIO_PIN_SHIFT (0x4)
#define IPC_VTT_GPIO_PIN_MASK (0x3f << 4)
+#define IPC_IO_ISOLATION_STAT_SHIFT (10)
+#define IPC_IO_ISOLATION_STAT_MASK (0x1 << 10)
#define M3_STATE_UNKNOWN 0
#define M3_STATE_RESET 1
@@ -228,6 +230,11 @@ static void wkup_m3_set_vtt_gpio(struct wkup_m3_ipc *m3_ipc, int gpio)
(gpio << IPC_VTT_GPIO_PIN_SHIFT);
}
+static void wkup_m3_set_io_isolation(struct wkup_m3_ipc *m3_ipc)
+{
+ m3_ipc->isolation_conf = (1 << IPC_IO_ISOLATION_STAT_SHIFT);
+}
+
/* Public functions */
/**
* wkup_m3_set_mem_type - Pass wkup_m3 which type of memory is in use
@@ -308,8 +315,8 @@ static int wkup_m3_prepare_low_power(struct wkup_m3_ipc *m3_ipc, int state)
wkup_m3_ctrl_ipc_write(m3_ipc, m3_ipc->resume_addr, 0);
wkup_m3_ctrl_ipc_write(m3_ipc, m3_power_state, 1);
wkup_m3_ctrl_ipc_write(m3_ipc, m3_ipc->mem_type |
- m3_ipc->vtt_conf, 4);
-
+ m3_ipc->vtt_conf |
+ m3_ipc->isolation_conf, 4);
wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 2);
wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 3);
wkup_m3_ctrl_ipc_write(m3_ipc, DS_IPC_DEFAULT, 5);
@@ -519,6 +526,9 @@ static int wkup_m3_ipc_probe(struct platform_device *pdev)
dev_warn(dev, "Invalid VTT GPIO(%d) pin\n", temp);
}
+ if (of_find_property(np, "ti,set-io-isolation", NULL))
+ wkup_m3_set_io_isolation(m3_ipc);
+
/*
* Wait for firmware loading completion in a thread so we
* can boot the wkup_m3 as soon as it's ready without holding
diff --git a/include/linux/wkup_m3_ipc.h b/include/linux/wkup_m3_ipc.h
index 2bc52c6381d5..b706eac58f92 100644
--- a/include/linux/wkup_m3_ipc.h
+++ b/include/linux/wkup_m3_ipc.h
@@ -34,6 +34,7 @@ struct wkup_m3_ipc {
int mem_type;
unsigned long resume_addr;
int vtt_conf;
+ int isolation_conf;
int state;
struct completion sync_complete;
--
2.32.0
