Re: [PATCH v3 2/2] hwmon: Add driver for Texas Instruments TMP464 and TMP468

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Guenter,

Le 16/02/2022 à 08:07, Guenter Roeck a écrit :
Add support for Texas Instruments TMP464 and TMP468 temperature sensor
ICs.

TI's TMP464 is an I2C temperature sensor chip. This chip is
similar to TI's TMP421 chip, but with 16bit-wide registers (instead
of 8bit-wide registers). The chip has one local sensor and four
remote sensors. TMP468 is similar to TMP464 but has one local and
eight remote sensors.

Originally-from: Agathe Porte <agathe.porte@xxxxxxxxx>
Cc: Agathe Porte <agathe.porte@xxxxxxxxx>
Cc: Krzysztof Adamski <krzysztof.adamski@xxxxxxxxx>
Signed-off-by: Guenter Roeck <linux@xxxxxxxxxxxx>
---
v3:
- Added support for TMP468
- Added support for various limits, temperature hysteresis, alarm attributes,
   and update interval
- Use regmap instead of local caching
- Use static chip configuration
- Unlock check if needed when loading driver, and lock it when unloading it
   - Call tmp464_init_client() before calling tmp464_probe_from_dt()
     since the latter changes registers, which requires the chip to be
     unlocked.
- Restore configuration register when unloading driver
- ti,n-factor is optional, so don't fail if the property is not present

Notes:
- Tested with real TMP468. Module tested for TMP464.
- I was not able to test with a system supporting devicetree;
   especially negative values for "ti,n-factor" need testing
   (and I wonder if of_property_read_s8() would be needed to
    support this properly).

I just did the test on our system and both positive and negative value n-factor fails.

With the following overlay:

/dts-v1/;
/plugin/;
/ {
        fragment@0 {
                target-path = "/soc/.../i2c@4/tmp464@49";
                __overlay__ {
                        #address-cells = <1>;
                        #size-cells = <0>;

                        channel@0 {
                                reg = <0x0>;
                                label = "local";
                                ti,n-factor = /bits/ 8 <(-10)>;
                        };

                        channel@1 {
                                reg = <0x1>;
                                label = "ch1";
                        };

                        channel@2 {
                                reg = <0x2>;
                                label = "ch2";
                        };

                        channel@3 {
                                reg = <0x3>;
                                label = "ch3";
                        };

                        channel@4 {
                                reg = <0x4>;
                                label = "ch4";
                        };
                };
        };

};

I get the following probing error:

[ 3580.557425] tmp464: probe of 16-0049 failed with error -75

With a positive n-factor in the overlay (<(10)> instead of <(-10)>), the driver *does not load either*, with the same error message.

Without any n-factor set, the v3 driver you proposed loads just fine with the DT.

Any idea of where this could come from? This was probably not working in my own implementation either.

PS: check your spam folder eventually for my mail asking delivery details of the TMP464 samples.

Bests,

Agathe.




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux