Schema changes:
- support for mdio-connected switches (mdio driver), recognized by
checking the presence of property "reg"
- new compatible strings for rtl8367s and rtl8367rb
- "interrupt-controller" was not added as a required property. It might
still work polling the ports when missing.
Examples changes:
- renamed "switch_intc" to make it unique between examples
- removed "dsa-mdio" from mdio compatible property
- renamed phy@0 to ethernet-phy@0 (not tested with real HW)
phy@ requires #phy-cells
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@xxxxxxxxx>
---
.../bindings/net/dsa/realtek-smi.txt | 240 -----------
.../devicetree/bindings/net/dsa/realtek.yaml | 394 ++++++++++++++++++
2 files changed, 394 insertions(+), 240 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/net/dsa/realtek-smi.txt
create mode 100644 Documentation/devicetree/bindings/net/dsa/realtek.yaml
diff --git a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt b/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt
deleted file mode 100644
index 7959ec237983..000000000000
--- a/Documentation/devicetree/bindings/net/dsa/realtek-smi.txt
+++ /dev/null
@@ -1,240 +0,0 @@
-Realtek SMI-based Switches
-==========================
-
-The SMI "Simple Management Interface" is a two-wire protocol using
-bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does
-not use the MDIO protocol. This binding defines how to specify the
-SMI-based Realtek devices.
-
-Required properties:
-
-- compatible: must be exactly one of:
- "realtek,rtl8365mb" (4+1 ports)
- "realtek,rtl8366"
- "realtek,rtl8366rb" (4+1 ports)
- "realtek,rtl8366s" (4+1 ports)
- "realtek,rtl8367"
- "realtek,rtl8367b"
- "realtek,rtl8368s" (8 port)
- "realtek,rtl8369"
- "realtek,rtl8370" (8 port)
-
-Required properties:
-- mdc-gpios: GPIO line for the MDC clock line.
-- mdio-gpios: GPIO line for the MDIO data line.
-- reset-gpios: GPIO line for the reset signal.
-
-Optional properties:
-- realtek,disable-leds: if the LED drivers are not used in the
- hardware design this will disable them so they are not turned on
- and wasting power.
-
-Required subnodes:
-
-- interrupt-controller
-
- This defines an interrupt controller with an IRQ line (typically
- a GPIO) that will demultiplex and handle the interrupt from the single
- interrupt line coming out of one of the SMI-based chips. It most
- importantly provides link up/down interrupts to the PHY blocks inside
- the ASIC.
-
-Required properties of interrupt-controller:
-
-- interrupt: parent interrupt, see interrupt-controller/interrupts.txt
-- interrupt-controller: see interrupt-controller/interrupts.txt
-- #address-cells: should be <0>
-- #interrupt-cells: should be <1>
-
-- mdio
-
- This defines the internal MDIO bus of the SMI device, mostly for the
- purpose of being able to hook the interrupts to the right PHY and
- the right PHY to the corresponding port.
-
-Required properties of mdio:
-
-- compatible: should be set to "realtek,smi-mdio" for all SMI devices
-
-See net/mdio.txt for additional MDIO bus properties.
-
-See net/dsa/dsa.txt for a list of additional required and optional properties
-and subnodes of DSA switches.
-
-Examples:
-
-An example for the RTL8366RB:
-
-switch {
- compatible = "realtek,rtl8366rb";
- /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
- mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
- mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
-
- switch_intc: interrupt-controller {
- /* GPIO 15 provides the interrupt */
- interrupt-parent = <&gpio0>;
- interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <1>;
- };
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
- port@0 {
- reg = <0>;
- label = "lan0";
- phy-handle = <&phy0>;
- };
- port@1 {
- reg = <1>;
- label = "lan1";
- phy-handle = <&phy1>;
- };
- port@2 {
- reg = <2>;
- label = "lan2";
- phy-handle = <&phy2>;
- };
- port@3 {
- reg = <3>;
- label = "lan3";
- phy-handle = <&phy3>;
- };
- port@4 {
- reg = <4>;
- label = "wan";
- phy-handle = <&phy4>;
- };
- port@5 {
- reg = <5>;
- label = "cpu";
- ethernet = <&gmac0>;
- phy-mode = "rgmii";
- fixed-link {
- speed = <1000>;
- full-duplex;
- };
- };
- };
-
- mdio {
- compatible = "realtek,smi-mdio", "dsa-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
-
- phy0: phy@0 {
- reg = <0>;
- interrupt-parent = <&switch_intc>;
- interrupts = <0>;
- };
- phy1: phy@1 {
- reg = <1>;
- interrupt-parent = <&switch_intc>;
- interrupts = <1>;
- };
- phy2: phy@2 {
- reg = <2>;
- interrupt-parent = <&switch_intc>;
- interrupts = <2>;
- };
- phy3: phy@3 {
- reg = <3>;
- interrupt-parent = <&switch_intc>;
- interrupts = <3>;
- };
- phy4: phy@4 {
- reg = <4>;
- interrupt-parent = <&switch_intc>;
- interrupts = <12>;
- };
- };
-};
-
-An example for the RTL8365MB-VC:
-
-switch {
- compatible = "realtek,rtl8365mb";
- mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
- mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
- reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
-
- switch_intc: interrupt-controller {
- interrupt-parent = <&gpio5>;
- interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
- interrupt-controller;
- #address-cells = <0>;
- #interrupt-cells = <1>;
- };
-
- ports {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
- port@0 {
- reg = <0>;
- label = "swp0";
- phy-handle = <ðphy0>;
- };
- port@1 {
- reg = <1>;
- label = "swp1";
- phy-handle = <ðphy1>;
- };
- port@2 {
- reg = <2>;
- label = "swp2";
- phy-handle = <ðphy2>;
- };
- port@3 {
- reg = <3>;
- label = "swp3";
- phy-handle = <ðphy3>;
- };
- port@6 {
- reg = <6>;
- label = "cpu";
- ethernet = <&fec1>;
- phy-mode = "rgmii";
- tx-internal-delay-ps = <2000>;
- rx-internal-delay-ps = <2000>;
-
- fixed-link {
- speed = <1000>;
- full-duplex;
- pause;
- };
- };
- };
-
- mdio {
- compatible = "realtek,smi-mdio";
- #address-cells = <1>;
- #size-cells = <0>;
-
- ethphy0: phy@0 {
- reg = <0>;
- interrupt-parent = <&switch_intc>;
- interrupts = <0>;
- };
- ethphy1: phy@1 {
- reg = <1>;
- interrupt-parent = <&switch_intc>;
- interrupts = <1>;
- };
- ethphy2: phy@2 {
- reg = <2>;
- interrupt-parent = <&switch_intc>;
- interrupts = <2>;
- };
- ethphy3: phy@3 {
- reg = <3>;
- interrupt-parent = <&switch_intc>;
- interrupts = <3>;
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/net/dsa/realtek.yaml b/Documentation/devicetree/bindings/net/dsa/realtek.yaml
new file mode 100644
index 000000000000..8756060895a8
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/dsa/realtek.yaml
@@ -0,0 +1,394 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/net/dsa/realtek.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Realtek switches for unmanaged switches
+
+allOf:
+ - $ref: dsa.yaml#
+
+maintainers:
+ - Linus Walleij <linus.walleij@xxxxxxxxxx>
+
+description:
+ Realtek advertises these chips as fast/gigabit switches or unmanaged
+ switches. They can be controlled using different interfaces, like SMI,
+ MDIO or SPI.
+
+ The SMI "Simple Management Interface" is a two-wire protocol using
+ bit-banged GPIO that while it reuses the MDIO lines MCK and MDIO does
+ not use the MDIO protocol. This binding defines how to specify the
+ SMI-based Realtek devices. The realtek-smi driver is a platform driver
+ and it must be inserted inside a platform node.
+
+ The MDIO-connected switches use MDIO protocol to access their registers.
+ The realtek-mdio driver is an MDIO driver and it must be inserted inside
+ an MDIO node.
+
+properties:
+ compatible:
+ enum:
+ - realtek,rtl8365mb
+ - realtek,rtl8366
+ - realtek,rtl8366rb
+ - realtek,rtl8366s
+ - realtek,rtl8367
+ - realtek,rtl8367b
+ - realtek,rtl8367rb
+ - realtek,rtl8367s
+ - realtek,rtl8368s
+ - realtek,rtl8369
+ - realtek,rtl8370
+ description: |
+ realtek,rtl8365mb: 4+1 ports
+ realtek,rtl8366: 5+1 ports
+ realtek,rtl8366rb: 5+1 ports
+ realtek,rtl8366s: 5+1 ports
+ realtek,rtl8367:
+ realtek,rtl8367b:
+ realtek,rtl8367rb: 5+2 ports
+ realtek,rtl8367s: 5+2 ports
+ realtek,rtl8368s: 8 ports
+ realtek,rtl8369: 8+1 ports
+ realtek,rtl8370: 8+2 ports
+
+ mdc-gpios:
+ description: GPIO line for the MDC clock line.
+ maxItems: 1
+
+ mdio-gpios:
+ description: GPIO line for the MDIO data line.
+ maxItems: 1
+
+ reset-gpios:
+ description: GPIO to be used to reset the whole device
+ maxItems: 1
+
+ realtek,disable-leds:
+ type: boolean
+ description: |
+ if the LED drivers are not used in the hardware design,
+ this will disable them so they are not turned on
+ and wasting power.
+
+ interrupt-controller:
+ type: object
+ description: |
+ This defines an interrupt controller with an IRQ line (typically
+ a GPIO) that will demultiplex and handle the interrupt from the single
+ interrupt line coming out of one of the Realtek switch chips. It most
+ importantly provides link up/down interrupts to the PHY blocks inside
+ the ASIC.
+
+ properties:
+
+ interrupt-controller: true
+
+ interrupts:
+ maxItems: 1
+ description:
+ A single IRQ line from the switch, either active LOW or HIGH
+
+ '#address-cells':
+ const: 0
+
+ '#interrupt-cells':
+ const: 1
+
+ required:
+ - interrupt-controller
+ - '#address-cells'
+ - '#interrupt-cells'
+
+ mdio:
+ $ref: /schemas/net/mdio.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ compatible:
+ const: realtek,smi-mdio
+
+if:
+ required:
+ - reg
+
+then:
+ not:
+ required:
+ - mdc-gpios
+ - mdio-gpios
+ - mdio
+
+ properties:
+ mdc-gpios: false
+ mdio-gpios: false
+ mdio: false
+
+else:
+ required:
+ - mdc-gpios
+ - mdio-gpios
+ - mdio
+ - reset-gpios
+
+required:
+ - compatible
+
+ # - mdc-gpios
+ # - mdio-gpios
+ # - reset-gpios
+ # - mdio
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ platform {
+ switch {
+ compatible = "realtek,rtl8366rb";
+ /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
+ mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
+ mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
+
+ switch_intc1: interrupt-controller {
+ /* GPIO 15 provides the interrupt */
+ interrupt-parent = <&gpio0>;
+ interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ label = "lan0";
+ phy-handle = <&phy0>;
+ };
+ port@1 {
+ reg = <1>;
+ label = "lan1";
+ phy-handle = <&phy1>;
+ };
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ phy-handle = <&phy2>;
+ };
+ port@3 {
+ reg = <3>;
+ label = "lan3";
+ phy-handle = <&phy3>;
+ };
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ phy-handle = <&phy4>;
+ };
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ ethernet = <&gmac0>;
+ phy-mode = "rgmii";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+
+ mdio {
+ compatible = "realtek,smi-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy@0 {
+ reg = <0>;
+ interrupt-parent = <&switch_intc1>;
+ interrupts = <0>;
+ };
+ phy1: ethernet-phy@1 {
+ reg = <1>;
+ interrupt-parent = <&switch_intc1>;
+ interrupts = <1>;
+ };
+ phy2: ethernet-phy@2 {
+ reg = <2>;
+ interrupt-parent = <&switch_intc1>;
+ interrupts = <2>;
+ };
+ phy3: ethernet-phy@3 {
+ reg = <3>;
+ interrupt-parent = <&switch_intc1>;
+ interrupts = <3>;
+ };
+ phy4: ethernet-phy@4 {
+ reg = <4>;
+ interrupt-parent = <&switch_intc1>;
+ interrupts = <12>;
+ };
+ };
+ };
+ };
+
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ platform {
+ switch {
+ compatible = "realtek,rtl8365mb";
+ mdc-gpios = <&gpio1 16 GPIO_ACTIVE_HIGH>;
+ mdio-gpios = <&gpio1 17 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&gpio5 0 GPIO_ACTIVE_LOW>;
+
+ switch_intc2: interrupt-controller {
+ interrupt-parent = <&gpio5>;
+ interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port@0 {
+ reg = <0>;
+ label = "swp0";
+ phy-handle = <ðphy0>;
+ };
+ port@1 {
+ reg = <1>;
+ label = "swp1";
+ phy-handle = <ðphy1>;
+ };
+ port@2 {
+ reg = <2>;
+ label = "swp2";
+ phy-handle = <ðphy2>;
+ };
+ port@3 {
+ reg = <3>;
+ label = "swp3";
+ phy-handle = <ðphy3>;
+ };
+ port@6 {
+ reg = <6>;
+ label = "cpu";
+ ethernet = <&fec1>;
+ phy-mode = "rgmii";
+ tx-internal-delay-ps = <2000>;
+ rx-internal-delay-ps = <2000>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ pause;
+ };
+ };
+ };
+
+ mdio {
+ compatible = "realtek,smi-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy0: ethernet-phy@0 {
+ reg = <0>;
+ interrupt-parent = <&switch_intc2>;
+ interrupts = <0>;
+ };
+ ethphy1: ethernet-phy@1 {
+ reg = <1>;
+ interrupt-parent = <&switch_intc2>;
+ interrupts = <1>;
+ };
+ ethphy2: ethernet-phy@2 {
+ reg = <2>;
+ interrupt-parent = <&switch_intc2>;
+ interrupts = <2>;
+ };
+ ethphy3: ethernet-phy@3 {
+ reg = <3>;
+ interrupt-parent = <&switch_intc2>;
+ interrupts = <3>;
+ };
+ };
+ };
+ };
+
+ - |
+ #include <dt-bindings/gpio/gpio.h>
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ switch@29 {
+ compatible = "realtek,rtl8367s";
+ reg = <29>;
+
+ reset-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
+
+ switch_intc3: interrupt-controller {
+ interrupt-parent = <&gpio0>;
+ interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #address-cells = <0>;
+ #interrupt-cells = <1>;
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan4";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan3";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan2";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan1";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "wan";
+ };
+
+ port@7 {
+ reg = <7>;
+ ethernet = <ðernet>;
+ phy-mode = "rgmii";
+ tx-internal-delay-ps = <2000>;
+ rx-internal-delay-ps = <0>;
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+ };
--
2.35.1
