updates:
* seperate leds into multiple groups
* switch sled numbering to 1-based
* disable inchip rtc
* add flash1 in fmc
* switch spi2 pnor using spi-gpio
* update gpio-line-names
* add interrupt pin for each sledx_ioexp
* enable mdio3
* update ADM1278 shunt resistor (300 micro Ohm)
* add INA230 for each sled
Signed-off-by: Potin Lai <potin.lai@xxxxxxxxxxxx>
---
Changes v2 -> v3:
- enable mdio3
- update ADM1278 shunt resistor (300 micro Ohm)
- change sys_log_id default state to off
- add INA230 for each sled
Changes v1 -> v2:
- add interrupt pin for each sledx_ioexp
- remove duplicated i2c1 node
- remove all PCA955X_TYPE_GPIO (default is GPIO)
---
.../dts/aspeed-bmc-facebook-bletchley.dts | 362 ++++++++++++------
1 file changed, 235 insertions(+), 127 deletions(-)
diff --git a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
index f973ea883b97..d0017bca86ad 100644
--- a/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
+++ b/arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts
@@ -5,6 +5,8 @@
#include "aspeed-g6.dtsi"
#include <dt-bindings/gpio/aspeed-gpio.h>
#include <dt-bindings/usb/pd.h>
+#include <dt-bindings/leds/leds-pca955x.h>
+#include <dt-bindings/interrupt-controller/irq.h>
/ {
model = "Facebook Bletchley BMC";
@@ -53,113 +55,139 @@
// Fixed link
};
- leds {
+ front_leds {
compatible = "gpio-leds";
-
sys_log_id {
- retain-state-shutdown;
- default-state = "keep";
- gpios = <&front_leds 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ gpios = <&pca_front 0 GPIO_ACTIVE_HIGH>;
};
+ };
+
+ fan_leds {
+ compatible = "gpio-leds";
fan0_blue {
retain-state-shutdown;
- default-state = "on";
- gpios = <&fan_ioexp 8 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ gpios = <&pca_fan 8 GPIO_ACTIVE_HIGH>;
};
fan1_blue {
retain-state-shutdown;
- default-state = "on";
- gpios = <&fan_ioexp 9 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ gpios = <&pca_fan 9 GPIO_ACTIVE_HIGH>;
};
fan2_blue {
retain-state-shutdown;
- default-state = "on";
- gpios = <&fan_ioexp 10 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ gpios = <&pca_fan 10 GPIO_ACTIVE_HIGH>;
};
fan3_blue {
retain-state-shutdown;
- default-state = "on";
- gpios = <&fan_ioexp 11 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ gpios = <&pca_fan 11 GPIO_ACTIVE_HIGH>;
};
fan0_amber {
retain-state-shutdown;
- default-state = "off";
- gpios = <&fan_ioexp 12 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ gpios = <&pca_fan 12 GPIO_ACTIVE_HIGH>;
};
fan1_amber {
retain-state-shutdown;
- default-state = "off";
- gpios = <&fan_ioexp 13 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ gpios = <&pca_fan 13 GPIO_ACTIVE_HIGH>;
};
fan2_amber {
retain-state-shutdown;
- default-state = "off";
- gpios = <&fan_ioexp 14 GPIO_ACTIVE_HIGH>;
+ default-state = "keep";
+ gpios = <&pca_fan 14 GPIO_ACTIVE_HIGH>;
};
fan3_amber {
retain-state-shutdown;
- default-state = "off";
- gpios = <&fan_ioexp 15 GPIO_ACTIVE_HIGH>;
- };
- sled0_amber {
- retain-state-shutdown;
- default-state = "off";
- gpios = <&sled0_leds 0 GPIO_ACTIVE_LOW>;
- };
- sled0_blue {
- retain-state-shutdown;
- default-state = "off";
- gpios = <&sled0_leds 1 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ gpios = <&pca_fan 15 GPIO_ACTIVE_HIGH>;
};
+ };
+
+ sled1_leds {
+ compatible = "gpio-leds";
sled1_amber {
retain-state-shutdown;
- default-state = "off";
- gpios = <&sled1_leds 0 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ gpios = <&pca_sled1 0 GPIO_ACTIVE_LOW>;
};
sled1_blue {
retain-state-shutdown;
- default-state = "off";
- gpios = <&sled1_leds 1 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ gpios = <&pca_sled1 1 GPIO_ACTIVE_LOW>;
};
+ };
+
+ sled2_leds {
+ compatible = "gpio-leds";
sled2_amber {
retain-state-shutdown;
- default-state = "off";
- gpios = <&sled2_leds 0 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ gpios = <&pca_sled2 0 GPIO_ACTIVE_LOW>;
};
sled2_blue {
retain-state-shutdown;
- default-state = "off";
- gpios = <&sled2_leds 1 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ gpios = <&pca_sled2 1 GPIO_ACTIVE_LOW>;
};
+ };
+
+ sled3_leds {
+ compatible = "gpio-leds";
sled3_amber {
retain-state-shutdown;
- default-state = "off";
- gpios = <&sled3_leds 0 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ gpios = <&pca_sled3 0 GPIO_ACTIVE_LOW>;
};
sled3_blue {
retain-state-shutdown;
- default-state = "off";
- gpios = <&sled3_leds 1 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ gpios = <&pca_sled3 1 GPIO_ACTIVE_LOW>;
};
+ };
+
+ sled4_leds {
+ compatible = "gpio-leds";
sled4_amber {
retain-state-shutdown;
- default-state = "off";
- gpios = <&sled4_leds 0 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ gpios = <&pca_sled4 0 GPIO_ACTIVE_LOW>;
};
sled4_blue {
retain-state-shutdown;
- default-state = "off";
- gpios = <&sled4_leds 1 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ gpios = <&pca_sled4 1 GPIO_ACTIVE_LOW>;
};
+ };
+
+ sled5_leds {
+ compatible = "gpio-leds";
sled5_amber {
retain-state-shutdown;
- default-state = "off";
- gpios = <&sled5_leds 0 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ gpios = <&pca_sled5 0 GPIO_ACTIVE_LOW>;
};
sled5_blue {
retain-state-shutdown;
- default-state = "off";
- gpios = <&sled5_leds 1 GPIO_ACTIVE_LOW>;
+ default-state = "keep";
+ gpios = <&pca_sled5 1 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ sled6_leds {
+ compatible = "gpio-leds";
+ sled6_amber {
+ retain-state-shutdown;
+ default-state = "keep";
+ gpios = <&pca_sled6 0 GPIO_ACTIVE_LOW>;
+ };
+ sled6_blue {
+ retain-state-shutdown;
+ default-state = "keep";
+ gpios = <&pca_sled6 1 GPIO_ACTIVE_LOW>;
};
};
};
@@ -178,7 +206,8 @@
};
&rtc {
- status = "okay";
+ /* Use nxp,pcf85263 (i2c 6-0051) instead */
+ status = "disabled";
};
&fmc {
@@ -188,26 +217,48 @@
m25p,fast-read;
label = "bmc";
spi-max-frequency = <50000000>;
+ spi-tx-bus-width = <2>;
+ spi-rx-bus-width = <2>;
#include "openbmc-flash-layout-128.dtsi"
};
+ flash@1 {
+ status = "okay";
+ m25p,fast-read;
+ label = "flash1";
+ spi-max-frequency = <50000000>;
+ spi-tx-bus-width = <2>;
+ spi-rx-bus-width = <2>;
+ };
};
&spi2 {
status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&pinctrl_spi2_default>;
+
+ compatible = "spi-gpio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ gpio-sck = <&gpio0 ASPEED_GPIO(X, 3) GPIO_ACTIVE_HIGH>;
+ gpio-mosi = <&gpio0 ASPEED_GPIO(X, 4) GPIO_ACTIVE_HIGH>;
+ gpio-miso = <&gpio0 ASPEED_GPIO(X, 5) GPIO_ACTIVE_HIGH>;
+ num-chipselects = <1>;
+ cs-gpios = <&gpio0 ASPEED_GPIO(X, 0) GPIO_ACTIVE_LOW>;
flash@0 {
status = "okay";
m25p,fast-read;
label = "pnor";
- spi-max-frequency = <100000000>;
+ spi-max-frequency = <12000000>;
};
};
&i2c0 {
status = "okay";
- /* TODO: Add ADC INA230 */
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
mp5023@40 {
compatible = "mps,mp5023";
@@ -219,7 +270,7 @@
reg = <0x4f>;
};
- sled0_ioexp: pca9539@76 {
+ sled1_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
@@ -227,14 +278,19 @@
gpio-controller;
#gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 0) IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
gpio-line-names =
- "SLED0_MS_DETECT1","SLED0_VBUS_BMC_EN","SLED0_INA230_ALERT","SLED0_P12V_STBY_ALERT",
- "SLED0_SSD_ALERT","SLED0_MS_DETECT0","SLED0_RST_CCG5","SLED0_FUSB302_INT",
- "SLED0_MD_STBY_RESET","SLED0_MD_IOEXP_EN_FAULT","SLED0_MD_DIR","SLED0_MD_DECAY",
- "SLED0_MD_MODE1","SLED0_MD_MODE2","SLED0_MD_MODE3","power-host0";
+ "SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
+ "SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
+ "SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
+ "SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
};
- sled0_leds: pca9552@67 {
+ pca_sled1: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -243,13 +299,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled0-amber","led-sled0-blue","SLED0_RST_IOEXP","",
+ "led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","SLED1_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
};
- sled0_fusb302: typec-portc@22 {
+ sled1_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
@@ -270,7 +326,11 @@
&i2c1 {
status = "okay";
- /* TODO: Add ADC INA230 */
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
mp5023@40 {
compatible = "mps,mp5023";
@@ -282,7 +342,7 @@
reg = <0x4f>;
};
- sled1_ioexp: pca9539@76 {
+ sled2_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
@@ -290,14 +350,19 @@
gpio-controller;
#gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 1) IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
gpio-line-names =
- "SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
- "SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
- "SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
- "SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
+ "SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT",
+ "SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT",
+ "SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY",
+ "SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2";
};
- sled1_leds: pca9552@67 {
+ pca_sled2: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -306,13 +371,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","",
+ "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","SLED2_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
};
- sled1_fusb302: typec-portc@22 {
+ sled2_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
@@ -331,13 +396,13 @@
};
};
-&i2c1 {
- status = "okay";
-};
-
&i2c2 {
status = "okay";
- /* TODO: Add ADC INA230 */
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
mp5023@40 {
compatible = "mps,mp5023";
@@ -349,7 +414,7 @@
reg = <0x4f>;
};
- sled2_ioexp: pca9539@76 {
+ sled3_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
@@ -357,14 +422,19 @@
gpio-controller;
#gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 2) IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
gpio-line-names =
- "SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT",
- "SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT",
- "SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY",
- "SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2";
+ "SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT",
+ "SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT",
+ "SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY",
+ "SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3";
};
- sled2_leds: pca9552@67 {
+ pca_sled3: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -373,13 +443,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","",
+ "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","SLED3_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
};
- sled2_fusb302: typec-portc@22 {
+ sled3_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
@@ -400,7 +470,11 @@
&i2c3 {
status = "okay";
- /* TODO: Add ADC INA230 */
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
mp5023@40 {
compatible = "mps,mp5023";
@@ -412,7 +486,7 @@
reg = <0x4f>;
};
- sled3_ioexp: pca9539@76 {
+ sled4_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
@@ -420,14 +494,19 @@
gpio-controller;
#gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 3) IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
gpio-line-names =
- "SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT",
- "SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT",
- "SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY",
- "SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3";
+ "SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT",
+ "SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT",
+ "SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY",
+ "SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4";
};
- sled3_leds: pca9552@67 {
+ pca_sled4: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -436,13 +515,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","",
+ "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","SLED4_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
};
- sled3_fusb302: typec-portc@22 {
+ sled4_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
@@ -463,7 +542,11 @@
&i2c4 {
status = "okay";
- /* TODO: Add ADC INA230 */
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
mp5023@40 {
compatible = "mps,mp5023";
@@ -475,7 +558,7 @@
reg = <0x4f>;
};
- sled4_ioexp: pca9539@76 {
+ sled5_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
@@ -483,14 +566,19 @@
gpio-controller;
#gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 4) IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
gpio-line-names =
- "SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT",
- "SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT",
- "SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY",
- "SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4";
+ "SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT",
+ "SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT",
+ "SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY",
+ "SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5";
};
- sled4_leds: pca9552@67 {
+ pca_sled5: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -499,13 +587,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","",
+ "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","SLED5_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
};
- sled4_fusb302: typec-portc@22 {
+ sled5_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
@@ -526,7 +614,11 @@
&i2c5 {
status = "okay";
- /* TODO: Add ADC INA230 */
+ ina230@45 {
+ compatible = "ti,ina230";
+ reg = <0x45>;
+ shunt-resistor = <2000>;
+ };
mp5023@40 {
compatible = "mps,mp5023";
@@ -538,7 +630,7 @@
reg = <0x4f>;
};
- sled5_ioexp: pca9539@76 {
+ sled6_ioexp: pca9539@76 {
compatible = "nxp,pca9539";
reg = <0x76>;
#address-cells = <1>;
@@ -546,14 +638,19 @@
gpio-controller;
#gpio-cells = <2>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <ASPEED_GPIO(M, 5) IRQ_TYPE_LEVEL_LOW>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
gpio-line-names =
- "SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT",
- "SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT",
- "SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY",
- "SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5";
+ "SLED6_MS_DETECT1","SLED6_VBUS_BMC_EN","SLED6_INA230_ALERT","SLED6_P12V_STBY_ALERT",
+ "SLED6_SSD_ALERT","SLED6_MS_DETECT0","SLED6_RST_CCG5","SLED6_FUSB302_INT",
+ "SLED6_MD_STBY_RESET","SLED6_MD_IOEXP_EN_FAULT","SLED6_MD_DIR","SLED6_MD_DECAY",
+ "SLED6_MD_MODE1","SLED6_MD_MODE2","SLED6_MD_MODE3","power-host6";
};
- sled5_leds: pca9552@67 {
+ pca_sled6: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -562,13 +659,13 @@
#gpio-cells = <2>;
gpio-line-names =
- "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","",
+ "led-sled6-amber","led-sled6-blue","SLED6_RST_IOEXP","SLED6_MD_REF_PWM",
"","","","",
"","","","",
"","","","";
};
- sled5_fusb302: typec-portc@22 {
+ sled6_fusb302: typec-portc@22 {
compatible = "fcs,fusb302";
reg = <0x22>;
@@ -632,7 +729,7 @@
reg = <0x40>;
};
- front_leds: pca9552@67 {
+ pca_front: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -655,6 +752,7 @@
adm1278@11 {
compatible = "adi,adm1278";
reg = <0x11>;
+ shunt-resistor-micro-ohms = <300>;
};
tmp421@4c {
@@ -667,7 +765,7 @@
reg = <0x4d>;
};
- fan_ioexp: pca9552@67 {
+ pca_fan: pca9552@67 {
compatible = "nxp,pca9552";
reg = <0x67>;
#address-cells = <1>;
@@ -700,36 +798,38 @@
/*D0-D7*/ "","","","","","","","",
/*E0-E7*/ "","","","","","","","",
/*F0-F7*/ "","","","","","","","",
- /*G0-G7*/ "","SWITCH_FRU_MUX","","","","","","",
+ /*G0-G7*/ "BSM_FRU_WP","SWITCH_FRU_MUX","","",
+ "PWRGD_P1V05_VDDCORE","PWRGD_P1V5_VDD","","",
/*H0-H7*/ "presence-riser1","presence-riser2",
- "presence-sled0","presence-sled1",
- "presence-sled2","presence-sled3",
- "presence-sled4","presence-sled5",
+ "presence-sled1","presence-sled2",
+ "presence-sled3","presence-sled4",
+ "presence-sled5","presence-sled6",
/*I0-I7*/ "REV_ID0","","REV_ID1","REV_ID2",
- "","","","",
+ "","BSM_FLASH_WP_STATUS","BMC_TPM_PRES","",
/*J0-J7*/ "","","","","","","","",
/*K0-K7*/ "","","","","","","","",
- /*L0-L7*/ "","","","","","","","",
- /*M0-M7*/ "ALERT_SLED0","ALERT_SLED1",
- "ALERT_SLED2","ALERT_SLED3",
- "ALERT_SLED4","ALERT_SLED5",
+ /*L0-L7*/ "","","","","","BMC_RTC_INT","","",
+ /*M0-M7*/ "ALERT_SLED1","ALERT_SLED2",
+ "ALERT_SLED3","ALERT_SLED4",
+ "ALERT_SLED5","ALERT_SLED6",
"P12V_AUX_ALERT1","",
/*N0-N7*/ "","","","","","","","",
/*O0-O7*/ "","","","",
"","BOARD_ID0","BOARD_ID1","BOARD_ID2",
- /*P0-P7*/ "","","","","","","","",
+ /*P0-P7*/ "","","","","","","","BMC_HEARTBEAT",
/*Q0-Q7*/ "","","","","","","","",
/*R0-R7*/ "","","","","","","","",
/*S0-S7*/ "","","","BAT_DETECT",
"BMC_BT_WP0","BMC_BT_WP1","","",
/*T0-T7*/ "","","","","","","","",
/*U0-U7*/ "","","","","","","","",
- /*V0-V7*/ "","RST_BMC_MVL","","",
+ /*V0-V7*/ "PWRGD_CNS_PSU","RST_BMC_MVL","","PSU_PRSNT",
"USB2_SEL0_A","USB2_SEL1_A",
"USB2_SEL0_B","USB2_SEL1_B",
/*W0-W7*/ "RST_FRONT_IOEXP","","","","","","","",
/*X0-X7*/ "","","","","","","","",
- /*Y0-Y7*/ "","","BSM_FLASH_LATCH","","","","","",
+ /*Y0-Y7*/ "BMC_SELF_HW_RST","BSM_PRSNT","BSM_FLASH_LATCH","",
+ "","","","",
/*Z0-Z7*/ "","","","","","","","";
};
@@ -754,3 +854,11 @@
&pinctrl_adc12_default &pinctrl_adc13_default
&pinctrl_adc14_default &pinctrl_adc15_default>;
};
+
+&mdio3 {
+ status = "okay";
+ ethphy0: ethernet-phy@0 {
+ compatible = "ethernet-phy-id002b.09ae";
+ reg = <0>;
+ };
+};
--
2.17.1
