Re: [PATCH v5 4/5] PCI: qcom: Add interconnect support to 2.7.0/1.9.0 ops

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 03/02/2022 18:57, Bjorn Andersson wrote:
On Sat 18 Dec 06:10 PST 2021, Dmitry Baryshkov wrote:

Add optional interconnect support for the 2.7.0/1.9.0 hosts. Set the
bandwidth according to the values from the downstream driver.


What memory transactions will travel this path? I would expect there to
be two different paths involved, given the rather low bw numbers I
presume this is the config path?

I think so. Downstream votes on this path for most of the known SoCs. Two spotted omissions are ipq8074 and qcs404.


Is there no vote for the data path?

CNSS devices can vote additionally on the MASTER_PCI to memory paths:
For sm845 (45 = MASTER_PCIE):
                qcom,msm-bus,vectors-KBps =
                        <45 512 0 0>,
                        <45 512 600000 800000>; /* ~4.6Gbps (MCS12) */

On sm8150/sm8250 qca bindings do not contain a vote, but wil6210 does (100 = MASTER_PCIE_1):
                qcom,msm-bus,vectors-KBps =
                        <100 512 0 0>,
                        <100 512 600000 800000>; /* ~4.6Gbps (MCS12) */

For sm8450 there are two paths used by cnss:
		<&pcie_noc MASTER_PCIE_0 &pcie_noc SLAVE_ANOC_PCIE_GEM_NOC>,
		<&gem_noc MASTER_ANOC_PCIE_GEM_NOC &mc_virt SLAVE_EBI1>;

with multiple entries per each path.

So, I'm not sure about these values.


Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
---
  drivers/pci/controller/dwc/pcie-qcom.c | 11 +++++++++++
  1 file changed, 11 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index d8d400423a0a..55ac3caa6d7d 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -12,6 +12,7 @@
  #include <linux/crc8.h>
  #include <linux/delay.h>
  #include <linux/gpio/consumer.h>
+#include <linux/interconnect.h>
  #include <linux/interrupt.h>
  #include <linux/io.h>
  #include <linux/iopoll.h>
@@ -167,6 +168,7 @@ struct qcom_pcie_resources_2_7_0 {
  	struct clk *pipe_clk_src;
  	struct clk *phy_pipe_clk;
  	struct clk *ref_clk_src;
+	struct icc_path *path;
  };
union qcom_pcie_resources {
@@ -1121,6 +1123,10 @@ static int qcom_pcie_get_resources_2_7_0(struct qcom_pcie *pcie)
  	if (IS_ERR(res->pci_reset))
  		return PTR_ERR(res->pci_reset);
+ res->path = devm_of_icc_get(dev, "pci");

The paths are typically identified using a string of the form
<source>-<destination>.


I don't see the related update to the DT binding for the introduction of
the interconnect.

Regards,
Bjorn

+	if (IS_ERR(res->path))
+		return PTR_ERR(res->path);
+
  	res->supplies[0].supply = "vdda";
  	res->supplies[1].supply = "vddpe-3v3";
  	ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(res->supplies),
@@ -1183,6 +1189,9 @@ static int qcom_pcie_init_2_7_0(struct qcom_pcie *pcie)
  	if (pcie->cfg->pipe_clk_need_muxing)
  		clk_set_parent(res->pipe_clk_src, res->phy_pipe_clk);
+ if (res->path)
+		icc_set_bw(res->path, 500, 800);
+
  	ret = clk_bulk_prepare_enable(res->num_clks, res->clks);
  	if (ret < 0)
  		goto err_disable_regulators;
@@ -1241,6 +1250,8 @@ static void qcom_pcie_deinit_2_7_0(struct qcom_pcie *pcie)
  	struct qcom_pcie_resources_2_7_0 *res = &pcie->res.v2_7_0;
clk_bulk_disable_unprepare(res->num_clks, res->clks);
+	if (res->path)
+		icc_set_bw(res->path, 0, 0);
/* Set TCXO as clock source for pcie_pipe_clk_src */
  	if (pcie->cfg->pipe_clk_need_muxing)
--
2.34.1



--
With best wishes
Dmitry



[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux