On Wed 02 Feb 03:18 PST 2022, Marijn Suijten wrote:
> On 2022-01-28 16:54:29, Bjorn Andersson wrote:
> > The Light Pulse Generator (LPG) is a PWM-block found in a wide range of
> > PMICs from Qualcomm. These PMICs typically comes with 1-8 LPG instances,
> > with their output being routed to various other components, such as
> > current sinks or GPIOs.
> >
> > Each LPG instance can operate on fixed parameters or based on a shared
> > lookup-table, altering the duty cycle over time. This provides the means
> > for hardware assisted transitions of LED brightness.
> >
> > A typical use case for the fixed parameter mode is to drive a PWM
> > backlight control signal, the driver therefor allows each LPG instance
> > to be exposed to the kernel either through the LED framework or the PWM
> > framework.
> >
> > A typical use case for the LED configuration is to drive RGB LEDs in
> > smartphones etc, for which the driver support multiple channels to be
> > ganged up to a MULTICOLOR LED. In this configuration the pattern
> > generators will be synchronized, to allow for multi-color patterns.
> >
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
>
> Reviewed-by: Marijn Suijten <marijn.suijten@xxxxxxxxxxxxxx>
>
> There may still be some things to improve based on whether lo_pause
> works in non-ping-pong mode - to alleviate the requirement for the first
> delta_t to be at most 512ms - but this patch should not be delayed much
> longer and that's perhaps for a followup patch. Same for my request for
> documentation and examples which at the same time serve as some form of
> tests to see if everything works as desired.
>
I've been considering lopause to be the value before we start the
pattern, but I think you're right in that it denotes how long we should
hold the first value.
So I think it might make sense in the predefined "<value> <delay> <value>
<delay>" scheme to use first <delay> as to calculate lo-pause. I think
it has to be calculated, because the first value will iiuc be held
for (lopause + 1) * delay ms.
> I also vaguely remember other (downstream) drivers to support more than
> 512ms per step by (drastically?) changing PWM period, but not sure how
> that worked again nor if it was reliable.
>
Thinking about it again, while 512 is the 9th bit, we should be able to
represent [0..1023] with 9 bits...
Regards,
Bjorn
> - Marijn
>
> > ---
> >
> > Changes since v10:
> > - Check for and reject pattern.delta_t greater than 9 bits
> > - Write all 9 bits of LPG_RAMP_DURATION_REG
> >
> > drivers/leds/Kconfig | 3 +
> > drivers/leds/Makefile | 3 +
> > drivers/leds/rgb/Kconfig | 13 +
> > drivers/leds/rgb/Makefile | 3 +
> > drivers/leds/rgb/leds-qcom-lpg.c | 1306 ++++++++++++++++++++++++++++++
> > 5 files changed, 1328 insertions(+)
> > create mode 100644 drivers/leds/rgb/Kconfig
> > create mode 100644 drivers/leds/rgb/Makefile
> > create mode 100644 drivers/leds/rgb/leds-qcom-lpg.c
> >
> > diff --git a/drivers/leds/Kconfig b/drivers/leds/Kconfig
> > index 6090e647daee..a49979f41eee 100644
> > --- a/drivers/leds/Kconfig
> > +++ b/drivers/leds/Kconfig
> > @@ -869,6 +869,9 @@ source "drivers/leds/blink/Kconfig"
> > comment "Flash and Torch LED drivers"
> > source "drivers/leds/flash/Kconfig"
> >
> > +comment "RGB LED drivers"
> > +source "drivers/leds/rgb/Kconfig"
> > +
> > comment "LED Triggers"
> > source "drivers/leds/trigger/Kconfig"
> >
> > diff --git a/drivers/leds/Makefile b/drivers/leds/Makefile
> > index e58ecb36360f..4fd2f92cd198 100644
> > --- a/drivers/leds/Makefile
> > +++ b/drivers/leds/Makefile
> > @@ -99,6 +99,9 @@ obj-$(CONFIG_LEDS_USER) += uleds.o
> > # Flash and Torch LED Drivers
> > obj-$(CONFIG_LEDS_CLASS_FLASH) += flash/
> >
> > +# RGB LED Drivers
> > +obj-$(CONFIG_LEDS_CLASS_MULTICOLOR) += rgb/
> > +
> > # LED Triggers
> > obj-$(CONFIG_LEDS_TRIGGERS) += trigger/
> >
> > diff --git a/drivers/leds/rgb/Kconfig b/drivers/leds/rgb/Kconfig
> > new file mode 100644
> > index 000000000000..20be3e11fe4a
> > --- /dev/null
> > +++ b/drivers/leds/rgb/Kconfig
> > @@ -0,0 +1,13 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +
> > +if LEDS_CLASS_MULTICOLOR
> > +
> > +config LEDS_QCOM_LPG
> > + tristate "LED support for Qualcomm LPG"
> > + depends on OF
> > + depends on SPMI
> > + help
> > + This option enables support for the Light Pulse Generator found in a
> > + wide variety of Qualcomm PMICs.
> > +
> > +endif # LEDS_CLASS_MULTICOLOR
> > diff --git a/drivers/leds/rgb/Makefile b/drivers/leds/rgb/Makefile
> > new file mode 100644
> > index 000000000000..83114f44c4ea
> > --- /dev/null
> > +++ b/drivers/leds/rgb/Makefile
> > @@ -0,0 +1,3 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +
> > +obj-$(CONFIG_LEDS_QCOM_LPG) += leds-qcom-lpg.o
> > diff --git a/drivers/leds/rgb/leds-qcom-lpg.c b/drivers/leds/rgb/leds-qcom-lpg.c
> > new file mode 100644
> > index 000000000000..06d5fca1d4b5
> > --- /dev/null
> > +++ b/drivers/leds/rgb/leds-qcom-lpg.c
> > @@ -0,0 +1,1306 @@
> > +// SPDX-License-Identifier: GPL-2.0-only
> > +/*
> > + * Copyright (c) 2017-2022 Linaro Ltd
> > + * Copyright (c) 2010-2012, The Linux Foundation. All rights reserved.
> > + */
> > +#include <linux/bits.h>
> > +#include <linux/led-class-multicolor.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/pwm.h>
> > +#include <linux/regmap.h>
> > +#include <linux/slab.h>
> > +
> > +#define LPG_PATTERN_CONFIG_REG 0x40
> > +#define LPG_SIZE_CLK_REG 0x41
> > +#define LPG_PREDIV_CLK_REG 0x42
> > +#define PWM_TYPE_CONFIG_REG 0x43
> > +#define PWM_VALUE_REG 0x44
> > +#define PWM_ENABLE_CONTROL_REG 0x46
> > +#define PWM_SYNC_REG 0x47
> > +#define LPG_RAMP_DURATION_REG 0x50
> > +#define LPG_HI_PAUSE_REG 0x52
> > +#define LPG_LO_PAUSE_REG 0x54
> > +#define LPG_HI_IDX_REG 0x56
> > +#define LPG_LO_IDX_REG 0x57
> > +#define PWM_SEC_ACCESS_REG 0xd0
> > +#define PWM_DTEST_REG(x) (0xe2 + (x) - 1)
> > +
> > +#define TRI_LED_SRC_SEL 0x45
> > +#define TRI_LED_EN_CTL 0x46
> > +#define TRI_LED_ATC_CTL 0x47
> > +
> > +#define LPG_LUT_REG(x) (0x40 + (x) * 2)
> > +#define RAMP_CONTROL_REG 0xc8
> > +
> > +#define LPG_RESOLUTION 512
> > +#define LPG_MAX_M 7
> > +
> > +struct lpg_channel;
> > +struct lpg_data;
> > +
> > +/**
> > + * struct lpg - LPG device context
> > + * @dev: struct device for LPG device
> > + * @map: regmap for register access
> > + * @pwm: PWM-chip object, if operating in PWM mode
> > + * @data: reference to version specific data
> > + * @lut_base: base address of the LUT block (optional)
> > + * @lut_size: number of entries in the LUT block
> > + * @lut_bitmap: allocation bitmap for LUT entries
> > + * @triled_base: base address of the TRILED block (optional)
> > + * @triled_src: power-source for the TRILED
> > + * @triled_has_atc_ctl: true if there is TRI_LED_ATC_CTL register
> > + * @triled_has_src_sel: true if there is TRI_LED_SRC_SEL register
> > + * @channels: list of PWM channels
> > + * @num_channels: number of @channels
> > + */
> > +struct lpg {
> > + struct device *dev;
> > + struct regmap *map;
> > +
> > + struct pwm_chip pwm;
> > +
> > + const struct lpg_data *data;
> > +
> > + u32 lut_base;
> > + u32 lut_size;
> > + unsigned long *lut_bitmap;
> > +
> > + u32 triled_base;
> > + u32 triled_src;
> > + bool triled_has_atc_ctl;
> > + bool triled_has_src_sel;
> > +
> > + struct lpg_channel *channels;
> > + unsigned int num_channels;
> > +};
> > +
> > +/**
> > + * struct lpg_channel - per channel data
> > + * @lpg: reference to parent lpg
> > + * @base: base address of the PWM channel
> > + * @triled_mask: mask in TRILED to enable this channel
> > + * @lut_mask: mask in LUT to start pattern generator for this channel
> > + * @in_use: channel is exposed to LED framework
> > + * @color: color of the LED attached to this channel
> > + * @dtest_line: DTEST line for output, or 0 if disabled
> > + * @dtest_value: DTEST line configuration
> > + * @pwm_value: duty (in microseconds) of the generated pulses, overridden by LUT
> > + * @enabled: output enabled?
> > + * @period: period (in nanoseconds) of the generated pulses
> > + * @clk: base frequency of the clock generator
> > + * @pre_div: divider of @clk
> > + * @pre_div_exp: exponential divider of @clk
> > + * @ramp_enabled: duty cycle is driven by iterating over lookup table
> > + * @ramp_ping_pong: reverse through pattern, rather than wrapping to start
> > + * @ramp_oneshot: perform only a single pass over the pattern
> > + * @ramp_reverse: iterate over pattern backwards
> > + * @ramp_tick_ms: length (in milliseconds) of one step in the pattern
> > + * @ramp_lo_pause_ms: pause (in milliseconds) before iterating over pattern
> > + * @ramp_hi_pause_ms: pause (in milliseconds) after iterating over pattern
> > + * @pattern_lo_idx: start index of associated pattern
> > + * @pattern_hi_idx: last index of associated pattern
> > + */
> > +struct lpg_channel {
> > + struct lpg *lpg;
> > +
> > + u32 base;
> > + unsigned int triled_mask;
> > + unsigned int lut_mask;
> > +
> > + bool in_use;
> > +
> > + int color;
> > +
> > + u32 dtest_line;
> > + u32 dtest_value;
> > +
> > + u16 pwm_value;
> > + bool enabled;
> > +
> > + u64 period;
> > + unsigned int clk;
> > + unsigned int pre_div;
> > + unsigned int pre_div_exp;
> > +
> > + bool ramp_enabled;
> > + bool ramp_ping_pong;
> > + bool ramp_oneshot;
> > + bool ramp_reverse;
> > + unsigned short ramp_tick_ms;
> > + unsigned long ramp_lo_pause_ms;
> > + unsigned long ramp_hi_pause_ms;
> > +
> > + unsigned int pattern_lo_idx;
> > + unsigned int pattern_hi_idx;
> > +};
> > +
> > +/**
> > + * struct lpg_led - logical LED object
> > + * @lpg: lpg context reference
> > + * @cdev: LED class device
> > + * @mcdev: Multicolor LED class device
> > + * @num_channels: number of @channels
> > + * @channels: list of channels associated with the LED
> > + */
> > +struct lpg_led {
> > + struct lpg *lpg;
> > +
> > + struct led_classdev cdev;
> > + struct led_classdev_mc mcdev;
> > +
> > + unsigned int num_channels;
> > + struct lpg_channel *channels[];
> > +};
> > +
> > +/**
> > + * struct lpg_channel_data - per channel initialization data
> > + * @base: base address for PWM channel registers
> > + * @triled_mask: bitmask for controlling this channel in TRILED
> > + */
> > +struct lpg_channel_data {
> > + unsigned int base;
> > + u8 triled_mask;
> > +};
> > +
> > +/**
> > + * struct lpg_data - initialization data
> > + * @lut_base: base address of LUT block
> > + * @lut_size: number of entries in LUT
> > + * @triled_base: base address of TRILED
> > + * @triled_has_atc_ctl: true if there is TRI_LED_ATC_CTL register
> > + * @triled_has_src_sel: true if there is TRI_LED_SRC_SEL register
> > + * @pwm_9bit_mask: bitmask for switching from 6bit to 9bit pwm
> > + * @num_channels: number of channels in LPG
> > + * @channels: list of channel initialization data
> > + */
> > +struct lpg_data {
> > + unsigned int lut_base;
> > + unsigned int lut_size;
> > + unsigned int triled_base;
> > + bool triled_has_atc_ctl;
> > + bool triled_has_src_sel;
> > + unsigned int pwm_9bit_mask;
> > + int num_channels;
> > + const struct lpg_channel_data *channels;
> > +};
> > +
> > +static int triled_set(struct lpg *lpg, unsigned int mask, unsigned int enable)
> > +{
> > + /* Skip if we don't have a triled block */
> > + if (!lpg->triled_base)
> > + return 0;
> > +
> > + return regmap_update_bits(lpg->map, lpg->triled_base + TRI_LED_EN_CTL,
> > + mask, enable);
> > +}
> > +
> > +static int lpg_lut_store(struct lpg *lpg, struct led_pattern *pattern,
> > + size_t len, unsigned int *lo_idx, unsigned int *hi_idx)
> > +{
> > + unsigned int idx;
> > + u16 val;
> > + int i;
> > +
> > + /* Hardware does not behave when LO_IDX == HI_IDX */
> > + if (len == 1)
> > + return -EINVAL;
> > +
> > + idx = bitmap_find_next_zero_area(lpg->lut_bitmap, lpg->lut_size,
> > + 0, len, 0);
> > + if (idx >= lpg->lut_size)
> > + return -ENOMEM;
> > +
> > + for (i = 0; i < len; i++) {
> > + val = pattern[i].brightness;
> > +
> > + regmap_bulk_write(lpg->map, lpg->lut_base + LPG_LUT_REG(idx + i),
> > + &val, sizeof(val));
> > + }
> > +
> > + bitmap_set(lpg->lut_bitmap, idx, len);
> > +
> > + *lo_idx = idx;
> > + *hi_idx = idx + len - 1;
> > +
> > + return 0;
> > +}
> > +
> > +static void lpg_lut_free(struct lpg *lpg, unsigned int lo_idx, unsigned int hi_idx)
> > +{
> > + int len;
> > +
> > + if (lo_idx == hi_idx)
> > + return;
> > +
> > + len = hi_idx - lo_idx + 1;
> > + bitmap_clear(lpg->lut_bitmap, lo_idx, len);
> > +}
> > +
> > +static int lpg_lut_sync(struct lpg *lpg, unsigned int mask)
> > +{
> > + return regmap_write(lpg->map, lpg->lut_base + RAMP_CONTROL_REG, mask);
> > +}
> > +
> > +static const unsigned int lpg_clk_rates[] = {1024, 32768, 19200000};
> > +static const unsigned int lpg_pre_divs[] = {1, 3, 5, 6};
> > +
> > +static int lpg_calc_freq(struct lpg_channel *chan, uint64_t period)
> > +{
> > + unsigned int clk, best_clk = 0;
> > + unsigned int div, best_div = 0;
> > + unsigned int m, best_m = 0;
> > + unsigned int error;
> > + unsigned int best_err = UINT_MAX;
> > + u64 best_period = 0;
> > +
> > + /*
> > + * The PWM period is determined by:
> > + *
> > + * resolution * pre_div * 2^M
> > + * period = --------------------------
> > + * refclk
> > + *
> > + * With resolution fixed at 2^9 bits, pre_div = {1, 3, 5, 6} and
> > + * M = [0..7].
> > + *
> > + * This allows for periods between 27uS and 384s, as the PWM framework
> > + * wants a period of equal or lower length than requested, reject
> > + * anything below 27uS.
> > + */
> > + if (period <= (u64)NSEC_PER_SEC * LPG_RESOLUTION / 19200000)
> > + return -EINVAL;
> > +
> > + /* Limit period to largest possible value, to avoid overflows */
> > + if (period > (u64)NSEC_PER_SEC * LPG_RESOLUTION * 6 * (1 << LPG_MAX_M) / 1024)
> > + period = (u64)NSEC_PER_SEC * LPG_RESOLUTION * 6 * (1 << LPG_MAX_M) / 2014;
> > +
> > + /*
> > + * Search for the pre_div, clk and M by solving the rewritten formula
> > + * for each clk and pre_div value:
> > + *
> > + * period * clk
> > + * M = log2 -------------------------------------
> > + * NSEC_PER_SEC * pre_div * resolution
> > + */
> > + for (clk = 0; clk < ARRAY_SIZE(lpg_clk_rates); clk++) {
> > + u64 nom = period * lpg_clk_rates[clk];
> > +
> > + for (div = 0; div < ARRAY_SIZE(lpg_pre_divs); div++) {
> > + u64 denom = (u64)NSEC_PER_SEC * lpg_pre_divs[div] * (1 << 9);
> > + u64 actual;
> > + u64 ratio;
> > +
> > + if (nom < denom)
> > + continue;
> > +
> > + ratio = div64_u64(nom, denom);
> > + m = ilog2(ratio);
> > + if (m > LPG_MAX_M)
> > + m = LPG_MAX_M;
> > +
> > + actual = DIV_ROUND_UP_ULL(denom * (1 << m), lpg_clk_rates[clk]);
> > +
> > + error = period - actual;
> > + if (error < best_err) {
> > + best_err = error;
> > +
> > + best_div = div;
> > + best_m = m;
> > + best_clk = clk;
> > + best_period = actual;
> > + }
> > + }
> > + }
> > +
> > + chan->clk = best_clk;
> > + chan->pre_div = best_div;
> > + chan->pre_div_exp = best_m;
> > + chan->period = best_period;
> > +
> > + return 0;
> > +}
> > +
> > +static void lpg_calc_duty(struct lpg_channel *chan, uint64_t duty)
> > +{
> > + unsigned int max = LPG_RESOLUTION - 1;
> > + unsigned int val;
> > +
> > + val = div64_u64(duty * lpg_clk_rates[chan->clk],
> > + (u64)NSEC_PER_SEC * lpg_pre_divs[chan->pre_div] * (1 << chan->pre_div_exp));
> > +
> > + chan->pwm_value = min(val, max);
> > +}
> > +
> > +static void lpg_apply_freq(struct lpg_channel *chan)
> > +{
> > + unsigned long val;
> > + struct lpg *lpg = chan->lpg;
> > +
> > + if (!chan->enabled)
> > + return;
> > +
> > + /* Clock register values are off-by-one from lpg_clk_table */
> > + val = chan->clk + 1;
> > +
> > + /* Enable 9bit resolution */
> > + val |= lpg->data->pwm_9bit_mask;
> > +
> > + regmap_write(lpg->map, chan->base + LPG_SIZE_CLK_REG, val);
> > +
> > + val = chan->pre_div << 5 | chan->pre_div_exp;
> > + regmap_write(lpg->map, chan->base + LPG_PREDIV_CLK_REG, val);
> > +}
> > +
> > +#define LPG_ENABLE_GLITCH_REMOVAL BIT(5)
> > +
> > +static void lpg_enable_glitch(struct lpg_channel *chan)
> > +{
> > + struct lpg *lpg = chan->lpg;
> > +
> > + regmap_update_bits(lpg->map, chan->base + PWM_TYPE_CONFIG_REG,
> > + LPG_ENABLE_GLITCH_REMOVAL, 0);
> > +}
> > +
> > +static void lpg_disable_glitch(struct lpg_channel *chan)
> > +{
> > + struct lpg *lpg = chan->lpg;
> > +
> > + regmap_update_bits(lpg->map, chan->base + PWM_TYPE_CONFIG_REG,
> > + LPG_ENABLE_GLITCH_REMOVAL,
> > + LPG_ENABLE_GLITCH_REMOVAL);
> > +}
> > +
> > +static void lpg_apply_pwm_value(struct lpg_channel *chan)
> > +{
> > + struct lpg *lpg = chan->lpg;
> > + u16 val = chan->pwm_value;
> > +
> > + if (!chan->enabled)
> > + return;
> > +
> > + regmap_bulk_write(lpg->map, chan->base + PWM_VALUE_REG, &val, sizeof(val));
> > +}
> > +
> > +#define LPG_PATTERN_CONFIG_LO_TO_HI BIT(4)
> > +#define LPG_PATTERN_CONFIG_REPEAT BIT(3)
> > +#define LPG_PATTERN_CONFIG_TOGGLE BIT(2)
> > +#define LPG_PATTERN_CONFIG_PAUSE_HI BIT(1)
> > +#define LPG_PATTERN_CONFIG_PAUSE_LO BIT(0)
> > +
> > +static void lpg_apply_lut_control(struct lpg_channel *chan)
> > +{
> > + struct lpg *lpg = chan->lpg;
> > + unsigned int hi_pause;
> > + unsigned int lo_pause;
> > + unsigned int conf = 0;
> > + unsigned int lo_idx = chan->pattern_lo_idx;
> > + unsigned int hi_idx = chan->pattern_hi_idx;
> > + u16 step = chan->ramp_tick_ms;
> > +
> > + if (!chan->ramp_enabled || chan->pattern_lo_idx == chan->pattern_hi_idx)
> > + return;
> > +
> > + hi_pause = DIV_ROUND_UP(chan->ramp_hi_pause_ms, step);
> > + lo_pause = DIV_ROUND_UP(chan->ramp_lo_pause_ms, step);
> > +
> > + if (!chan->ramp_reverse)
> > + conf |= LPG_PATTERN_CONFIG_LO_TO_HI;
> > + if (!chan->ramp_oneshot)
> > + conf |= LPG_PATTERN_CONFIG_REPEAT;
> > + if (chan->ramp_ping_pong)
> > + conf |= LPG_PATTERN_CONFIG_TOGGLE;
> > + if (chan->ramp_hi_pause_ms)
> > + conf |= LPG_PATTERN_CONFIG_PAUSE_HI;
> > + if (chan->ramp_lo_pause_ms)
> > + conf |= LPG_PATTERN_CONFIG_PAUSE_LO;
> > +
> > + regmap_write(lpg->map, chan->base + LPG_PATTERN_CONFIG_REG, conf);
> > + regmap_write(lpg->map, chan->base + LPG_HI_IDX_REG, hi_idx);
> > + regmap_write(lpg->map, chan->base + LPG_LO_IDX_REG, lo_idx);
> > +
> > + regmap_bulk_write(lpg->map, chan->base + LPG_RAMP_DURATION_REG, &step, sizeof(step));
> > + regmap_write(lpg->map, chan->base + LPG_HI_PAUSE_REG, hi_pause);
> > + regmap_write(lpg->map, chan->base + LPG_LO_PAUSE_REG, lo_pause);
> > +}
> > +
> > +#define LPG_ENABLE_CONTROL_OUTPUT BIT(7)
> > +#define LPG_ENABLE_CONTROL_BUFFER_TRISTATE BIT(5)
> > +#define LPG_ENABLE_CONTROL_SRC_PWM BIT(2)
> > +#define LPG_ENABLE_CONTROL_RAMP_GEN BIT(1)
> > +
> > +static void lpg_apply_control(struct lpg_channel *chan)
> > +{
> > + unsigned int ctrl;
> > + struct lpg *lpg = chan->lpg;
> > +
> > + ctrl = LPG_ENABLE_CONTROL_BUFFER_TRISTATE;
> > +
> > + if (chan->enabled)
> > + ctrl |= LPG_ENABLE_CONTROL_OUTPUT;
> > +
> > + if (chan->pattern_lo_idx != chan->pattern_hi_idx)
> > + ctrl |= LPG_ENABLE_CONTROL_RAMP_GEN;
> > + else
> > + ctrl |= LPG_ENABLE_CONTROL_SRC_PWM;
> > +
> > + regmap_write(lpg->map, chan->base + PWM_ENABLE_CONTROL_REG, ctrl);
> > +
> > + /*
> > + * Due to LPG hardware bug, in the PWM mode, having enabled PWM,
> > + * We have to write PWM values one more time.
> > + */
> > + if (chan->enabled)
> > + lpg_apply_pwm_value(chan);
> > +}
> > +
> > +#define LPG_SYNC_PWM BIT(0)
> > +
> > +static void lpg_apply_sync(struct lpg_channel *chan)
> > +{
> > + struct lpg *lpg = chan->lpg;
> > +
> > + regmap_write(lpg->map, chan->base + PWM_SYNC_REG, LPG_SYNC_PWM);
> > +}
> > +
> > +static int lpg_parse_dtest(struct lpg *lpg)
> > +{
> > + struct lpg_channel *chan;
> > + struct device_node *np = lpg->dev->of_node;
> > + int count;
> > + int ret;
> > + int i;
> > +
> > + count = of_property_count_u32_elems(np, "qcom,dtest");
> > + if (count == -EINVAL) {
> > + return 0;
> > + } else if (count < 0) {
> > + ret = count;
> > + goto err_malformed;
> > + } else if (count != lpg->data->num_channels * 2) {
> > + dev_err(lpg->dev, "qcom,dtest needs to be %d items\n",
> > + lpg->data->num_channels * 2);
> > + return -EINVAL;
> > + }
> > +
> > + for (i = 0; i < lpg->data->num_channels; i++) {
> > + chan = &lpg->channels[i];
> > +
> > + ret = of_property_read_u32_index(np, "qcom,dtest", i * 2,
> > + &chan->dtest_line);
> > + if (ret)
> > + goto err_malformed;
> > +
> > + ret = of_property_read_u32_index(np, "qcom,dtest", i * 2 + 1,
> > + &chan->dtest_value);
> > + if (ret)
> > + goto err_malformed;
> > + }
> > +
> > + return 0;
> > +
> > +err_malformed:
> > + dev_err(lpg->dev, "malformed qcom,dtest\n");
> > + return ret;
> > +}
> > +
> > +static void lpg_apply_dtest(struct lpg_channel *chan)
> > +{
> > + struct lpg *lpg = chan->lpg;
> > +
> > + if (!chan->dtest_line)
> > + return;
> > +
> > + regmap_write(lpg->map, chan->base + PWM_SEC_ACCESS_REG, 0xa5);
> > + regmap_write(lpg->map, chan->base + PWM_DTEST_REG(chan->dtest_line),
> > + chan->dtest_value);
> > +}
> > +
> > +static void lpg_apply(struct lpg_channel *chan)
> > +{
> > + lpg_disable_glitch(chan);
> > + lpg_apply_freq(chan);
> > + lpg_apply_pwm_value(chan);
> > + lpg_apply_control(chan);
> > + lpg_apply_sync(chan);
> > + lpg_apply_lut_control(chan);
> > + lpg_enable_glitch(chan);
> > +}
> > +
> > +static void lpg_brightness_set(struct lpg_led *led, struct led_classdev *cdev,
> > + struct mc_subled *subleds)
> > +{
> > + enum led_brightness brightness;
> > + struct lpg_channel *chan;
> > + unsigned int triled_enabled = 0;
> > + unsigned int triled_mask = 0;
> > + unsigned int lut_mask = 0;
> > + unsigned int duty;
> > + struct lpg *lpg = led->lpg;
> > + int i;
> > +
> > + for (i = 0; i < led->num_channels; i++) {
> > + chan = led->channels[i];
> > + brightness = subleds[i].brightness;
> > +
> > + if (brightness == LED_OFF) {
> > + chan->enabled = false;
> > + chan->ramp_enabled = false;
> > + } else if (chan->pattern_lo_idx != chan->pattern_hi_idx) {
> > + lpg_calc_freq(chan, NSEC_PER_MSEC);
> > +
> > + chan->enabled = true;
> > + chan->ramp_enabled = true;
> > +
> > + lut_mask |= chan->lut_mask;
> > + triled_enabled |= chan->triled_mask;
> > + } else {
> > + lpg_calc_freq(chan, NSEC_PER_MSEC);
> > +
> > + duty = div_u64(brightness * chan->period, cdev->max_brightness);
> > + lpg_calc_duty(chan, duty);
> > + chan->enabled = true;
> > + chan->ramp_enabled = false;
> > +
> > + triled_enabled |= chan->triled_mask;
> > + }
> > +
> > + triled_mask |= chan->triled_mask;
> > +
> > + lpg_apply(chan);
> > + }
> > +
> > + /* Toggle triled lines */
> > + if (triled_mask)
> > + triled_set(lpg, triled_mask, triled_enabled);
> > +
> > + /* Trigger start of ramp generator(s) */
> > + if (lut_mask)
> > + lpg_lut_sync(lpg, lut_mask);
> > +}
> > +
> > +static void lpg_brightness_single_set(struct led_classdev *cdev,
> > + enum led_brightness value)
> > +{
> > + struct lpg_led *led = container_of(cdev, struct lpg_led, cdev);
> > + struct mc_subled info;
> > +
> > + info.brightness = value;
> > + lpg_brightness_set(led, cdev, &info);
> > +}
> > +
> > +static void lpg_brightness_mc_set(struct led_classdev *cdev,
> > + enum led_brightness value)
> > +{
> > + struct led_classdev_mc *mc = lcdev_to_mccdev(cdev);
> > + struct lpg_led *led = container_of(mc, struct lpg_led, mcdev);
> > +
> > + led_mc_calc_color_components(mc, value);
> > + lpg_brightness_set(led, cdev, mc->subled_info);
> > +}
> > +
> > +static int lpg_blink_set(struct lpg_led *led,
> > + unsigned long *delay_on, unsigned long *delay_off)
> > +{
> > + struct lpg_channel *chan;
> > + unsigned int period;
> > + unsigned int triled_mask = 0;
> > + struct lpg *lpg = led->lpg;
> > + u64 duty;
> > + int i;
> > +
> > + if (!*delay_on && !*delay_off) {
> > + *delay_on = 500;
> > + *delay_off = 500;
> > + }
> > +
> > + duty = *delay_on * NSEC_PER_MSEC;
> > + period = (*delay_on + *delay_off) * NSEC_PER_MSEC;
> > +
> > + for (i = 0; i < led->num_channels; i++) {
> > + chan = led->channels[i];
> > +
> > + lpg_calc_freq(chan, period);
> > + lpg_calc_duty(chan, duty);
> > +
> > + chan->enabled = true;
> > + chan->ramp_enabled = false;
> > +
> > + triled_mask |= chan->triled_mask;
> > +
> > + lpg_apply(chan);
> > + }
> > +
> > + /* Enable triled lines */
> > + triled_set(lpg, triled_mask, triled_mask);
> > +
> > + chan = led->channels[0];
> > + duty = div_u64(chan->pwm_value * chan->period, LPG_RESOLUTION);
> > + *delay_on = div_u64(duty, NSEC_PER_MSEC);
> > + *delay_off = div_u64(chan->period - duty, NSEC_PER_MSEC);
> > +
> > + return 0;
> > +}
> > +
> > +static int lpg_blink_single_set(struct led_classdev *cdev,
> > + unsigned long *delay_on, unsigned long *delay_off)
> > +{
> > + struct lpg_led *led = container_of(cdev, struct lpg_led, cdev);
> > +
> > + return lpg_blink_set(led, delay_on, delay_off);
> > +}
> > +
> > +static int lpg_blink_mc_set(struct led_classdev *cdev,
> > + unsigned long *delay_on, unsigned long *delay_off)
> > +{
> > + struct led_classdev_mc *mc = lcdev_to_mccdev(cdev);
> > + struct lpg_led *led = container_of(mc, struct lpg_led, mcdev);
> > +
> > + return lpg_blink_set(led, delay_on, delay_off);
> > +}
> > +
> > +static int lpg_pattern_set(struct lpg_led *led, struct led_pattern *pattern,
> > + u32 len, int repeat)
> > +{
> > + struct lpg_channel *chan;
> > + struct lpg *lpg = led->lpg;
> > + unsigned int hi_pause;
> > + unsigned int lo_pause;
> > + unsigned int lo_idx;
> > + unsigned int hi_idx;
> > + bool ping_pong = true;
> > + int brightness_a;
> > + int brightness_b;
> > + int ret;
> > + int i;
> > +
> > + /* Only support oneshot or indefinite loops, due to limited pattern space */
> > + if (repeat != -1 && repeat != 1)
> > + return -EINVAL;
> > +
> > + /* LPG_RAMP_DURATION_REG is 9 bit */
> > + if (pattern[0].delta_t >= 512)
> > + return -EINVAL;
> > +
> > + /*
> > + * The LPG plays patterns with at a fixed pace, a "low pause" can be
> > + * performed before the pattern and a "high pause" after. In order to
> > + * save space the pattern can be played in "ping pong" mode, in which
> > + * the pattern is first played forward, then "high pause" is applied,
> > + * then the pattern is played backwards and finally the "low pause" is
> > + * applied.
> > + *
> > + * The delta_t of the first entry is used to determine the pace of the
> > + * pattern.
> > + *
> > + * If the specified pattern is a palindrome the ping pong mode is
> > + * enabled. In this scenario the delta_t of the last entry determines
> > + * the "low pause" time and the delta_t of the middle entry (i.e. the
> > + * last in the programmed pattern) determines the "high pause". If the
> > + * pattern consists of an odd number of values, no "high pause" is
> > + * used.
> > + *
> > + * When ping pong mode is not selected, the delta_t of the last entry
> > + * is used as "high pause". No "low pause" is used.
> > + *
> > + * delta_t of any other members of the pattern is ignored.
> > + */
> > +
> > + /* Detect palindromes and use "ping pong" to reduce LUT usage */
> > + for (i = 0; i < len / 2; i++) {
> > + brightness_a = pattern[i].brightness;
> > + brightness_b = pattern[len - i - 1].brightness;
> > +
> > + if (brightness_a != brightness_b) {
> > + ping_pong = false;
> > + break;
> > + }
> > + }
> > +
> > + if (ping_pong) {
> > + if (len % 2)
> > + hi_pause = 0;
> > + else
> > + hi_pause = pattern[(len + 1) / 2].delta_t;
> > + lo_pause = pattern[len - 1].delta_t;
> > +
> > + len = (len + 1) / 2;
> > + } else {
> > + hi_pause = pattern[len - 1].delta_t;
> > + lo_pause = 0;
> > + }
> > +
> > + ret = lpg_lut_store(lpg, pattern, len, &lo_idx, &hi_idx);
> > + if (ret < 0)
> > + return ret;
> > +
> > + for (i = 0; i < led->num_channels; i++) {
> > + chan = led->channels[i];
> > +
> > + chan->ramp_tick_ms = pattern[0].delta_t;
> > + chan->ramp_ping_pong = ping_pong;
> > + chan->ramp_oneshot = repeat != -1;
> > +
> > + chan->ramp_lo_pause_ms = lo_pause;
> > + chan->ramp_hi_pause_ms = hi_pause;
> > +
> > + chan->pattern_lo_idx = lo_idx;
> > + chan->pattern_hi_idx = hi_idx;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int lpg_pattern_single_set(struct led_classdev *cdev,
> > + struct led_pattern *pattern, u32 len,
> > + int repeat)
> > +{
> > + struct lpg_led *led = container_of(cdev, struct lpg_led, cdev);
> > + int ret;
> > +
> > + ret = lpg_pattern_set(led, pattern, len, repeat);
> > + if (ret < 0)
> > + return ret;
> > +
> > + lpg_brightness_single_set(cdev, LED_FULL);
> > +
> > + return 0;
> > +}
> > +
> > +static int lpg_pattern_mc_set(struct led_classdev *cdev,
> > + struct led_pattern *pattern, u32 len,
> > + int repeat)
> > +{
> > + struct led_classdev_mc *mc = lcdev_to_mccdev(cdev);
> > + struct lpg_led *led = container_of(mc, struct lpg_led, mcdev);
> > + int ret;
> > +
> > + ret = lpg_pattern_set(led, pattern, len, repeat);
> > + if (ret < 0)
> > + return ret;
> > +
> > + led_mc_calc_color_components(mc, LED_FULL);
> > + lpg_brightness_set(led, cdev, mc->subled_info);
> > +
> > + return 0;
> > +}
> > +
> > +static int lpg_pattern_clear(struct lpg_led *led)
> > +{
> > + struct lpg_channel *chan;
> > + struct lpg *lpg = led->lpg;
> > + int i;
> > +
> > + chan = led->channels[0];
> > + lpg_lut_free(lpg, chan->pattern_lo_idx, chan->pattern_hi_idx);
> > +
> > + for (i = 0; i < led->num_channels; i++) {
> > + chan = led->channels[i];
> > + chan->pattern_lo_idx = 0;
> > + chan->pattern_hi_idx = 0;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int lpg_pattern_single_clear(struct led_classdev *cdev)
> > +{
> > + struct lpg_led *led = container_of(cdev, struct lpg_led, cdev);
> > +
> > + return lpg_pattern_clear(led);
> > +}
> > +
> > +static int lpg_pattern_mc_clear(struct led_classdev *cdev)
> > +{
> > + struct led_classdev_mc *mc = lcdev_to_mccdev(cdev);
> > + struct lpg_led *led = container_of(mc, struct lpg_led, mcdev);
> > +
> > + return lpg_pattern_clear(led);
> > +}
> > +
> > +static int lpg_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm)
> > +{
> > + struct lpg *lpg = container_of(chip, struct lpg, pwm);
> > + struct lpg_channel *chan = &lpg->channels[pwm->hwpwm];
> > +
> > + return chan->in_use ? -EBUSY : 0;
> > +}
> > +
> > +/*
> > + * Limitations:
> > + * - Updating both duty and period is not done atomically, so the output signal
> > + * will momentarily be a mix of the settings.
> > + */
> > +static int lpg_pwm_apply(struct pwm_chip *chip, struct pwm_device *pwm,
> > + const struct pwm_state *state)
> > +{
> > + struct lpg *lpg = container_of(chip, struct lpg, pwm);
> > + struct lpg_channel *chan = &lpg->channels[pwm->hwpwm];
> > + int ret;
> > +
> > + if (state->polarity != PWM_POLARITY_NORMAL)
> > + return -EINVAL;
> > +
> > + ret = lpg_calc_freq(chan, state->period);
> > + if (ret < 0)
> > + return ret;
> > +
> > + lpg_calc_duty(chan, state->duty_cycle);
> > + chan->enabled = state->enabled;
> > +
> > + lpg_apply(chan);
> > +
> > + triled_set(lpg, chan->triled_mask, chan->enabled ? chan->triled_mask : 0);
> > +
> > + return 0;
> > +}
> > +
> > +static void lpg_pwm_get_state(struct pwm_chip *chip, struct pwm_device *pwm,
> > + struct pwm_state *state)
> > +{
> > + struct lpg *lpg = container_of(chip, struct lpg, pwm);
> > + struct lpg_channel *chan = &lpg->channels[pwm->hwpwm];
> > + u64 duty = DIV_ROUND_UP_ULL(chan->pwm_value * chan->period, LPG_RESOLUTION - 1);
> > +
> > + state->period = chan->period;
> > + state->duty_cycle = duty;
> > + state->polarity = PWM_POLARITY_NORMAL;
> > + state->enabled = chan->enabled;
> > +}
> > +
> > +static const struct pwm_ops lpg_pwm_ops = {
> > + .request = lpg_pwm_request,
> > + .apply = lpg_pwm_apply,
> > + .get_state = lpg_pwm_get_state,
> > + .owner = THIS_MODULE,
> > +};
> > +
> > +static int lpg_add_pwm(struct lpg *lpg)
> > +{
> > + int ret;
> > +
> > + lpg->pwm.base = -1;
> > + lpg->pwm.dev = lpg->dev;
> > + lpg->pwm.npwm = lpg->num_channels;
> > + lpg->pwm.ops = &lpg_pwm_ops;
> > +
> > + ret = pwmchip_add(&lpg->pwm);
> > + if (ret)
> > + dev_err(lpg->dev, "failed to add PWM chip: ret %d\n", ret);
> > +
> > + return ret;
> > +}
> > +
> > +static int lpg_parse_channel(struct lpg *lpg, struct device_node *np,
> > + struct lpg_channel **channel)
> > +{
> > + struct lpg_channel *chan;
> > + u32 color = LED_COLOR_ID_GREEN;
> > + u32 reg;
> > + int ret;
> > +
> > + ret = of_property_read_u32(np, "reg", ®);
> > + if (ret || !reg || reg > lpg->num_channels) {
> > + dev_err(lpg->dev, "invalid \"reg\" of %pOFn\n", np);
> > + return -EINVAL;
> > + }
> > +
> > + chan = &lpg->channels[reg - 1];
> > + chan->in_use = true;
> > +
> > + ret = of_property_read_u32(np, "color", &color);
> > + if (ret < 0 && ret != -EINVAL) {
> > + dev_err(lpg->dev, "failed to parse \"color\" of %pOF\n", np);
> > + return ret;
> > + }
> > +
> > + chan->color = color;
> > +
> > + *channel = chan;
> > +
> > + return 0;
> > +}
> > +
> > +static int lpg_add_led(struct lpg *lpg, struct device_node *np)
> > +{
> > + struct led_init_data init_data = {};
> > + struct led_classdev *cdev;
> > + struct device_node *child;
> > + struct mc_subled *info;
> > + struct lpg_led *led;
> > + const char *state;
> > + int num_channels;
> > + u32 color = 0;
> > + int ret;
> > + int i;
> > +
> > + ret = of_property_read_u32(np, "color", &color);
> > + if (ret < 0 && ret != -EINVAL) {
> > + dev_err(lpg->dev, "failed to parse \"color\" of %pOF\n", np);
> > + return ret;
> > + }
> > +
> > + if (color == LED_COLOR_ID_RGB)
> > + num_channels = of_get_available_child_count(np);
> > + else
> > + num_channels = 1;
> > +
> > + led = devm_kzalloc(lpg->dev, struct_size(led, channels, num_channels), GFP_KERNEL);
> > + if (!led)
> > + return -ENOMEM;
> > +
> > + led->lpg = lpg;
> > + led->num_channels = num_channels;
> > +
> > + if (color == LED_COLOR_ID_RGB) {
> > + info = devm_kcalloc(lpg->dev, num_channels, sizeof(*info), GFP_KERNEL);
> > + if (!info)
> > + return -ENOMEM;
> > + i = 0;
> > + for_each_available_child_of_node(np, child) {
> > + ret = lpg_parse_channel(lpg, child, &led->channels[i]);
> > + if (ret < 0)
> > + return ret;
> > +
> > + info[i].color_index = led->channels[i]->color;
> > + info[i].intensity = LED_FULL;
> > + i++;
> > + }
> > +
> > + led->mcdev.subled_info = info;
> > + led->mcdev.num_colors = num_channels;
> > +
> > + cdev = &led->mcdev.led_cdev;
> > + cdev->brightness_set = lpg_brightness_mc_set;
> > + cdev->blink_set = lpg_blink_mc_set;
> > +
> > + /* Register pattern accessors only if we have a LUT block */
> > + if (lpg->lut_base) {
> > + cdev->pattern_set = lpg_pattern_mc_set;
> > + cdev->pattern_clear = lpg_pattern_mc_clear;
> > + }
> > + } else {
> > + ret = lpg_parse_channel(lpg, np, &led->channels[0]);
> > + if (ret < 0)
> > + return ret;
> > +
> > + cdev = &led->cdev;
> > + cdev->brightness_set = lpg_brightness_single_set;
> > + cdev->blink_set = lpg_blink_single_set;
> > +
> > + /* Register pattern accessors only if we have a LUT block */
> > + if (lpg->lut_base) {
> > + cdev->pattern_set = lpg_pattern_single_set;
> > + cdev->pattern_clear = lpg_pattern_single_clear;
> > + }
> > + }
> > +
> > + cdev->default_trigger = of_get_property(np, "linux,default-trigger", NULL);
> > + cdev->max_brightness = 255;
> > +
> > + if (!of_property_read_string(np, "default-state", &state) &&
> > + !strcmp(state, "on"))
> > + cdev->brightness = LED_FULL;
> > + else
> > + cdev->brightness = LED_OFF;
> > +
> > + cdev->brightness_set(cdev, cdev->brightness);
> > +
> > + init_data.fwnode = of_fwnode_handle(np);
> > +
> > + if (color == LED_COLOR_ID_RGB)
> > + ret = devm_led_classdev_multicolor_register_ext(lpg->dev, &led->mcdev, &init_data);
> > + else
> > + ret = devm_led_classdev_register_ext(lpg->dev, &led->cdev, &init_data);
> > + if (ret)
> > + dev_err(lpg->dev, "unable to register %s\n", cdev->name);
> > +
> > + return ret;
> > +}
> > +
> > +static int lpg_init_channels(struct lpg *lpg)
> > +{
> > + const struct lpg_data *data = lpg->data;
> > + int i;
> > +
> > + lpg->num_channels = data->num_channels;
> > + lpg->channels = devm_kcalloc(lpg->dev, data->num_channels,
> > + sizeof(struct lpg_channel), GFP_KERNEL);
> > + if (!lpg->channels)
> > + return -ENOMEM;
> > +
> > + for (i = 0; i < data->num_channels; i++) {
> > + lpg->channels[i].lpg = lpg;
> > + lpg->channels[i].base = data->channels[i].base;
> > + lpg->channels[i].triled_mask = data->channels[i].triled_mask;
> > + lpg->channels[i].lut_mask = BIT(i);
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int lpg_init_triled(struct lpg *lpg)
> > +{
> > + struct device_node *np = lpg->dev->of_node;
> > + int ret;
> > +
> > + /* Skip initialization if we don't have a triled block */
> > + if (!lpg->data->triled_base)
> > + return 0;
> > +
> > + lpg->triled_base = lpg->data->triled_base;
> > + lpg->triled_has_atc_ctl = lpg->data->triled_has_atc_ctl;
> > + lpg->triled_has_src_sel = lpg->data->triled_has_src_sel;
> > +
> > + if (lpg->triled_has_src_sel) {
> > + ret = of_property_read_u32(np, "qcom,power-source", &lpg->triled_src);
> > + if (ret || lpg->triled_src == 2 || lpg->triled_src > 3) {
> > + dev_err(lpg->dev, "invalid power source\n");
> > + return -EINVAL;
> > + }
> > + }
> > +
> > + /* Disable automatic trickle charge LED */
> > + if (lpg->triled_has_atc_ctl)
> > + regmap_write(lpg->map, lpg->triled_base + TRI_LED_ATC_CTL, 0);
> > +
> > + /* Configure power source */
> > + if (lpg->triled_has_src_sel)
> > + regmap_write(lpg->map, lpg->triled_base + TRI_LED_SRC_SEL, lpg->triled_src);
> > +
> > + /* Default all outputs to off */
> > + regmap_write(lpg->map, lpg->triled_base + TRI_LED_EN_CTL, 0);
> > +
> > + return 0;
> > +}
> > +
> > +static int lpg_init_lut(struct lpg *lpg)
> > +{
> > + const struct lpg_data *data = lpg->data;
> > + size_t bitmap_size;
> > +
> > + if (!data->lut_base)
> > + return 0;
> > +
> > + lpg->lut_base = data->lut_base;
> > + lpg->lut_size = data->lut_size;
> > +
> > + bitmap_size = BITS_TO_BYTES(lpg->lut_size);
> > + lpg->lut_bitmap = devm_kzalloc(lpg->dev, bitmap_size, GFP_KERNEL);
> > + if (!lpg->lut_bitmap)
> > + return -ENOMEM;
> > +
> > + return 0;
> > +}
> > +
> > +static int lpg_probe(struct platform_device *pdev)
> > +{
> > + struct device_node *np;
> > + struct lpg *lpg;
> > + int ret;
> > + int i;
> > +
> > + lpg = devm_kzalloc(&pdev->dev, sizeof(*lpg), GFP_KERNEL);
> > + if (!lpg)
> > + return -ENOMEM;
> > +
> > + lpg->data = of_device_get_match_data(&pdev->dev);
> > + if (!lpg->data)
> > + return -EINVAL;
> > +
> > + platform_set_drvdata(pdev, lpg);
> > +
> > + lpg->dev = &pdev->dev;
> > +
> > + lpg->map = dev_get_regmap(pdev->dev.parent, NULL);
> > + if (!lpg->map) {
> > + dev_err(&pdev->dev, "parent regmap unavailable\n");
> > + return -ENXIO;
> > + }
> > +
> > + ret = lpg_init_channels(lpg);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = lpg_parse_dtest(lpg);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = lpg_init_triled(lpg);
> > + if (ret < 0)
> > + return ret;
> > +
> > + ret = lpg_init_lut(lpg);
> > + if (ret < 0)
> > + return ret;
> > +
> > + for_each_available_child_of_node(pdev->dev.of_node, np) {
> > + ret = lpg_add_led(lpg, np);
> > + if (ret)
> > + return ret;
> > + }
> > +
> > + for (i = 0; i < lpg->num_channels; i++)
> > + lpg_apply_dtest(&lpg->channels[i]);
> > +
> > + return lpg_add_pwm(lpg);
> > +}
> > +
> > +static int lpg_remove(struct platform_device *pdev)
> > +{
> > + struct lpg *lpg = platform_get_drvdata(pdev);
> > +
> > + pwmchip_remove(&lpg->pwm);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct lpg_data pm8916_pwm_data = {
> > + .pwm_9bit_mask = BIT(2),
> > +
> > + .num_channels = 1,
> > + .channels = (const struct lpg_channel_data[]) {
> > + { .base = 0xbc00 },
> > + },
> > +};
> > +
> > +static const struct lpg_data pm8941_lpg_data = {
> > + .lut_base = 0xb000,
> > + .lut_size = 64,
> > +
> > + .triled_base = 0xd000,
> > + .triled_has_atc_ctl = true,
> > + .triled_has_src_sel = true,
> > +
> > + .pwm_9bit_mask = 3 << 4,
> > +
> > + .num_channels = 8,
> > + .channels = (const struct lpg_channel_data[]) {
> > + { .base = 0xb100 },
> > + { .base = 0xb200 },
> > + { .base = 0xb300 },
> > + { .base = 0xb400 },
> > + { .base = 0xb500, .triled_mask = BIT(5) },
> > + { .base = 0xb600, .triled_mask = BIT(6) },
> > + { .base = 0xb700, .triled_mask = BIT(7) },
> > + { .base = 0xb800 },
> > + },
> > +};
> > +
> > +static const struct lpg_data pm8994_lpg_data = {
> > + .lut_base = 0xb000,
> > + .lut_size = 64,
> > +
> > + .pwm_9bit_mask = 3 << 4,
> > +
> > + .num_channels = 6,
> > + .channels = (const struct lpg_channel_data[]) {
> > + { .base = 0xb100 },
> > + { .base = 0xb200 },
> > + { .base = 0xb300 },
> > + { .base = 0xb400 },
> > + { .base = 0xb500 },
> > + { .base = 0xb600 },
> > + },
> > +};
> > +
> > +static const struct lpg_data pmi8994_lpg_data = {
> > + .lut_base = 0xb000,
> > + .lut_size = 24,
> > +
> > + .triled_base = 0xd000,
> > + .triled_has_atc_ctl = true,
> > + .triled_has_src_sel = true,
> > +
> > + .pwm_9bit_mask = BIT(4),
> > +
> > + .num_channels = 4,
> > + .channels = (const struct lpg_channel_data[]) {
> > + { .base = 0xb100, .triled_mask = BIT(5) },
> > + { .base = 0xb200, .triled_mask = BIT(6) },
> > + { .base = 0xb300, .triled_mask = BIT(7) },
> > + { .base = 0xb400 },
> > + },
> > +};
> > +
> > +static const struct lpg_data pmi8998_lpg_data = {
> > + .lut_base = 0xb000,
> > + .lut_size = 49,
> > +
> > + .triled_base = 0xd000,
> > +
> > + .pwm_9bit_mask = BIT(4),
> > +
> > + .num_channels = 6,
> > + .channels = (const struct lpg_channel_data[]) {
> > + { .base = 0xb100 },
> > + { .base = 0xb200 },
> > + { .base = 0xb300, .triled_mask = BIT(5) },
> > + { .base = 0xb400, .triled_mask = BIT(6) },
> > + { .base = 0xb500, .triled_mask = BIT(7) },
> > + { .base = 0xb600 },
> > + },
> > +};
> > +
> > +static const struct lpg_data pm8150b_lpg_data = {
> > + .lut_base = 0xb000,
> > + .lut_size = 24,
> > +
> > + .triled_base = 0xd000,
> > +
> > + .pwm_9bit_mask = BIT(4),
> > +
> > + .num_channels = 2,
> > + .channels = (const struct lpg_channel_data[]) {
> > + { .base = 0xb100, .triled_mask = BIT(7) },
> > + { .base = 0xb200, .triled_mask = BIT(6) },
> > + },
> > +};
> > +
> > +static const struct lpg_data pm8150l_lpg_data = {
> > + .lut_base = 0xb000,
> > + .lut_size = 48,
> > +
> > + .triled_base = 0xd000,
> > +
> > + .pwm_9bit_mask = BIT(4),
> > +
> > + .num_channels = 5,
> > + .channels = (const struct lpg_channel_data[]) {
> > + { .base = 0xb100, .triled_mask = BIT(7) },
> > + { .base = 0xb200, .triled_mask = BIT(6) },
> > + { .base = 0xb300, .triled_mask = BIT(5) },
> > + { .base = 0xbc00 },
> > + { .base = 0xbd00 },
> > +
> > + },
> > +};
> > +
> > +static const struct of_device_id lpg_of_table[] = {
> > + { .compatible = "qcom,pm8150b-lpg", .data = &pm8150b_lpg_data },
> > + { .compatible = "qcom,pm8150l-lpg", .data = &pm8150l_lpg_data },
> > + { .compatible = "qcom,pm8916-pwm", .data = &pm8916_pwm_data },
> > + { .compatible = "qcom,pm8941-lpg", .data = &pm8941_lpg_data },
> > + { .compatible = "qcom,pm8994-lpg", .data = &pm8994_lpg_data },
> > + { .compatible = "qcom,pmi8994-lpg", .data = &pmi8994_lpg_data },
> > + { .compatible = "qcom,pmi8998-lpg", .data = &pmi8998_lpg_data },
> > + { .compatible = "qcom,pmc8180c-lpg", .data = &pm8150l_lpg_data },
> > + {}
> > +};
> > +MODULE_DEVICE_TABLE(of, lpg_of_table);
> > +
> > +static struct platform_driver lpg_driver = {
> > + .probe = lpg_probe,
> > + .remove = lpg_remove,
> > + .driver = {
> > + .name = "qcom-spmi-lpg",
> > + .of_match_table = lpg_of_table,
> > + },
> > +};
> > +module_platform_driver(lpg_driver);
> > +
> > +MODULE_DESCRIPTION("Qualcomm LPG LED driver");
> > +MODULE_LICENSE("GPL v2");
> > --
> > 2.33.1
> >
