This is version 4 of the WPCM450 pinctrl/GPIO driver patchset, with some small, (hopefully) final improvements and cleanups (see patches 4 and 5). I'm targetting 5.18, it's now too close to the 5.17 merge window anyway. Best regards, Jonathan Neuschäfer v3: - https://lore.kernel.org/lkml/20211224200935.93817-1-j.neuschaefer@xxxxxxx/ v2: - https://lore.kernel.org/lkml/20211207210823.1975632-1-j.neuschaefer@xxxxxxx/ v1: - https://lore.kernel.org/lkml/20210602120329.2444672-1-j.neuschaefer@xxxxxxx/ > This series adds support for pinctrl and GPIO in the Nuvoton WPCM450 SoC. > Both my DT bindings and my driver are based on the work done by others for > the newer Nuvoton NPCM7xx SoC, and I've tried to keep both similar. > > Instead of extending the pinctrl-npcm7xx driver to add WPCM450 support, > I copied/forked it. The pinmux mechanism is very similar (using MFSEL1 and > MFSEL2 registers), but the GPIO register interface has been redesigned for > NPCM7xx; adding support for the older GPIO controller would make the driver > harder to understand, while only enabling a small amount of code sharing. > > The DT binding in YAML format might make a good template for also converting > the nuvoton,npcm7xx-pinctrl binding to YAML. > > Both in the DT binding and in the driver I kept the name "pinctrl". For the > driver, I find it accurate enough because it handles pinctrl and GPIO. For > the DT node, it's a bit less accurate because the register block at 0xb8003000 > is about GPIOs, and pin control happens in the global control registers (GCR) > block, except for input debouncing. So, "GPIO" might be the more appropriate > name component there. Jonathan Neuschäfer (9): dt-bindings: arm/npcm: Add binding for global control registers (GCR) MAINTAINERS: Match all of bindings/arm/npcm/ as part of NPCM architecture ARM: dts: wpcm450: Add global control registers (GCR) node dt-bindings: pinctrl: Add Nuvoton WPCM450 pinctrl: nuvoton: Add driver for WPCM450 ARM: dts: wpcm450: Add pinctrl and GPIO nodes ARM: dts: wpcm450: Add pin functions ARM: dts: wpcm450-supermicro-x9sci-ln4f: Add GPIO LEDs and buttons ARM: dts: wpcm450: Add pinmux information to UART0 .../bindings/arm/npcm/nuvoton,gcr.yaml | 48 + .../pinctrl/nuvoton,wpcm450-pinctrl.yaml | 160 +++ MAINTAINERS | 2 + .../nuvoton-wpcm450-supermicro-x9sci-ln4f.dts | 43 + arch/arm/boot/dts/nuvoton-wpcm450.dtsi | 384 ++++++ drivers/pinctrl/Makefile | 2 +- drivers/pinctrl/nuvoton/Kconfig | 18 + drivers/pinctrl/nuvoton/Makefile | 1 + drivers/pinctrl/nuvoton/pinctrl-wpcm450.c | 1130 +++++++++++++++++ 9 files changed, 1787 insertions(+), 1 deletion(-) create mode 100644 Documentation/devicetree/bindings/arm/npcm/nuvoton,gcr.yaml create mode 100644 Documentation/devicetree/bindings/pinctrl/nuvoton,wpcm450-pinctrl.yaml create mode 100644 drivers/pinctrl/nuvoton/pinctrl-wpcm450.c -- 2.30.2
