Dear Rob,
Thanks for your comments~
For mt8195, the eth device node will look like:
eth: ethernet@11021000 {
compatible = "mediatek,mt8195-gmac", "snps,dwmac-5.10a";
...
clock-names = "axi",
"apb",
"mac_cg",
"mac_main",
"ptp_ref",
"rmii_internal";
clocks = <&pericfg_ao CLK_PERI_AO_ETHERNET>,
<&pericfg_ao CLK_PERI_AO_ETHERNET_BUS>,
<&pericfg_ao CLK_PERI_AO_ETHERNET_MAC>,
<&topckgen CLK_TOP_SNPS_ETH_250M>,
<&topckgen CLK_TOP_SNPS_ETH_62P4M_PTP>,
<&topckgen CLK_TOP_SNPS_ETH_50M_RMII>;
...
}
1. "rmii_internal" is a special clock only required for
RMII phy interface, dwmac-mediatek.c will enable clocks
invoking clk_bulk_prepare_enable(xx, 6) for RMII,
and clk_bulk_prepare_enable(xx, 5) for other phy interfaces.
so, mt2712/mt8195 all put "rmii_internal" clock to the
end of clock list to simplify clock handling.
If I put mac_cg as described above, a if condition is required
for clocks description in dt-binding, just like what I do in v7 send:
- if:
properties:
compatible:
contains:
enum:
- mediatek,mt2712-gmac
then:
properties:
clocks:
minItems: 5
items:
- description: AXI clock
- description: APB clock
- description: MAC Main clock
- description: PTP clock
- description: RMII reference clock provided by MAC
clock-names:
minItems: 5
items:
- const: axi
- const: apb
- const: mac_main
- const: ptp_ref
- const: rmii_internal
- if:
properties:
compatible:
contains:
enum:
- mediatek,mt8195-gmac
then:
properties:
clocks:
minItems: 6
items:
- description: AXI clock
- description: APB clock
- description: MAC clock gate
- description: MAC Main clock
- description: PTP clock
- description: RMII reference clock provided by MAC
This introduces some duplicated description.
2. If I put "mac_cg" to the end of clock list,
the dt-binding file can be simple just like
what we do in this v10 patch(need fix warnings reported by "make
DT_CHECKER_FLAGS=-m dt_binding_check").
But for mt8195:
the eth node in dts should be modified,
and eth driver clock handling will be complex;
We prefer 1(duplicated description one).
Can we just descirbe clocks/clocks-names for mt2712/mt8195 seperately?
Please kindly comment about this issue.
Thanks in advance.
On Thu, 2021-12-16 at 07:53 -0600, Rob Herring wrote:
> On Thu, 16 Dec 2021 13:53:28 +0800, Biao Huang wrote:
> > Add binding document for the ethernet on mt8195.
> >
> > Signed-off-by: Biao Huang <biao.huang@xxxxxxxxxxxx>
> > ---
> > .../bindings/net/mediatek-dwmac.yaml | 29
> > ++++++++++++++++---
> > 1 file changed, 25 insertions(+), 4 deletions(-)
> >
>
> My bot found errors running 'make DT_CHECKER_FLAGS=-m
> dt_binding_check'
> on your patch (DT_CHECKER_FLAGS is new in v5.13):
>
> yamllint warnings/errors:
>
> dtschema/dtc warnings/errors:
> /builds/robherring/linux-dt-
> review/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml:
> properties:clock-names: {'minItems': 5, 'maxItems': 6, 'items':
> [{'const': 'axi'}, {'const': 'apb'}, {'const': 'mac_main'}, {'const':
> 'ptp_ref'}, {'const': 'rmii_internal'}, {'const': 'mac_cg'}]} should
> not be valid under {'required': ['maxItems']}
> hint: "maxItems" is not needed with an "items" list
> from schema $id: http://devicetree.org/meta-schemas/items.yaml#
> /builds/robherring/linux-dt-
> review/Documentation/devicetree/bindings/net/mediatek-dwmac.yaml:
> ignoring, error in schema: properties: clock-names
> warning: no schema found in file:
> ./Documentation/devicetree/bindings/net/mediatek-dwmac.yaml
> Documentation/devicetree/bindings/net/mediatek-
> dwmac.example.dt.yaml:0:0: /example-0/ethernet@1101c000: failed to
> match any schema with compatible: ['mediatek,mt2712-gmac',
> 'snps,dwmac-4.20a']
>
> doc reference errors (make refcheckdocs):
>
> See https://patchwork.ozlabs.org/patch/1568902
>
> This check can fail if there are any dependencies. The base for a
> patch
> series is generally the most recent rc1.
>
> If you already ran 'make dt_binding_check' and didn't see the above
> error(s), then make sure 'yamllint' is installed and dt-schema is up
> to
> date:
>
> pip3 install dtschema --upgrade
>
> Please check and re-submit.
>
