RZ/G2L and RZ/G2LC SMARC EVK use same carrier board, but the pin
mapping between RZ/G2L and RZ/G2LC SMARC SoM are different.
Therefore we need to update carrier board pin definitions based
on corresponding SoM pin mapping.
Move pinctrl definitions out of RZ/G2L SMARC common file, so that
we can reuse the common file to support RZ/G2LC SMARC EVK.
Signed-off-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
---
.../boot/dts/renesas/r9a07g044l2-smarc.dts | 1 +
.../dts/renesas/rzg2l-smarc-pinfunction.dtsi | 137 ++++++++++++++++++
arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi | 127 ----------------
3 files changed, 138 insertions(+), 127 deletions(-)
create mode 100644 arch/arm64/boot/dts/renesas/rzg2l-smarc-pinfunction.dtsi
diff --git a/arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts b/arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts
index 247b0b3f1b58..886d38886d05 100644
--- a/arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts
+++ b/arch/arm64/boot/dts/renesas/r9a07g044l2-smarc.dts
@@ -8,6 +8,7 @@
/dts-v1/;
#include "r9a07g044l2.dtsi"
#include "rzg2l-smarc-som.dtsi"
+#include "rzg2l-smarc-pinfunction.dtsi"
#include "rzg2l-smarc.dtsi"
/ {
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-smarc-pinfunction.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-smarc-pinfunction.dtsi
new file mode 100644
index 000000000000..71d83e447670
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc-pinfunction.dtsi
@@ -0,0 +1,137 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+/*
+ * Device Tree Source for the RZ/G2L SMARC pincontrol parts
+ *
+ * Copyright (C) 2021 Renesas Electronics Corp.
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rzg2l-pinctrl.h>
+
+&pinctrl {
+ pinctrl-0 = <&sound_clk_pins>;
+ pinctrl-names = "default";
+
+ can0_pins: can0 {
+ pinmux = <RZG2L_PORT_PINMUX(10, 1, 2)>, /* TX */
+ <RZG2L_PORT_PINMUX(11, 0, 2)>; /* RX */
+ };
+
+ /* SW7 should be at position 2->3 so that GPIO8_CAN0_STB line is activated */
+ can0-stb {
+ gpio-hog;
+ gpios = <RZG2L_GPIO(42, 2) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "can0_stb";
+ };
+
+ can1_pins: can1 {
+ pinmux = <RZG2L_PORT_PINMUX(12, 1, 2)>, /* TX */
+ <RZG2L_PORT_PINMUX(13, 0, 2)>; /* RX */
+ };
+
+ /* SW8 should be at position 2->3 so that GPIO9_CAN1_STB line is activated */
+ can1-stb {
+ gpio-hog;
+ gpios = <RZG2L_GPIO(42, 3) GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "can1_stb";
+ };
+
+ i2c0_pins: i2c0 {
+ pins = "RIIC0_SDA", "RIIC0_SCL";
+ input-enable;
+ };
+
+ i2c1_pins: i2c1 {
+ pins = "RIIC1_SDA", "RIIC1_SCL";
+ input-enable;
+ };
+
+ i2c3_pins: i2c3 {
+ pinmux = <RZG2L_PORT_PINMUX(18, 0, 3)>, /* SDA */
+ <RZG2L_PORT_PINMUX(18, 1, 3)>; /* SCL */
+ };
+
+ scif0_pins: scif0 {
+ pinmux = <RZG2L_PORT_PINMUX(38, 0, 1)>, /* TxD */
+ <RZG2L_PORT_PINMUX(38, 1, 1)>; /* RxD */
+ };
+
+ scif2_pins: scif2 {
+ pinmux = <RZG2L_PORT_PINMUX(48, 0, 1)>, /* TxD */
+ <RZG2L_PORT_PINMUX(48, 1, 1)>, /* RxD */
+ <RZG2L_PORT_PINMUX(48, 3, 1)>, /* CTS# */
+ <RZG2L_PORT_PINMUX(48, 4, 1)>; /* RTS# */
+ };
+
+ sd1-pwr-en-hog {
+ gpio-hog;
+ gpios = <RZG2L_GPIO(39, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "sd1_pwr_en";
+ };
+
+ sdhi1_pins: sd1 {
+ sd1_data {
+ pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+ power-source = <3300>;
+ };
+
+ sd1_ctrl {
+ pins = "SD1_CLK", "SD1_CMD";
+ power-source = <3300>;
+ };
+
+ sd1_mux {
+ pinmux = <RZG2L_PORT_PINMUX(19, 0, 1)>; /* SD1_CD */
+ };
+ };
+
+ sdhi1_pins_uhs: sd1_uhs {
+ sd1_data_uhs {
+ pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
+ power-source = <1800>;
+ };
+
+ sd1_ctrl_uhs {
+ pins = "SD1_CLK", "SD1_CMD";
+ power-source = <1800>;
+ };
+
+ sd1_mux_uhs {
+ pinmux = <RZG2L_PORT_PINMUX(19, 0, 1)>; /* SD1_CD */
+ };
+ };
+
+ sound_clk_pins: sound_clk {
+ pins = "AUDIO_CLK1", "AUDIO_CLK2";
+ input-enable;
+ };
+
+ spi1_pins: spi1 {
+ pinmux = <RZG2L_PORT_PINMUX(44, 0, 1)>, /* CK */
+ <RZG2L_PORT_PINMUX(44, 1, 1)>, /* MOSI */
+ <RZG2L_PORT_PINMUX(44, 2, 1)>, /* MISO */
+ <RZG2L_PORT_PINMUX(44, 3, 1)>; /* SSL */
+ };
+
+ ssi0_pins: ssi0 {
+ pinmux = <RZG2L_PORT_PINMUX(45, 0, 1)>, /* BCK */
+ <RZG2L_PORT_PINMUX(45, 1, 1)>, /* RCK */
+ <RZG2L_PORT_PINMUX(45, 2, 1)>, /* TXD */
+ <RZG2L_PORT_PINMUX(45, 3, 1)>; /* RXD */
+ };
+
+ usb0_pins: usb0 {
+ pinmux = <RZG2L_PORT_PINMUX(4, 0, 1)>, /* VBUS */
+ <RZG2L_PORT_PINMUX(5, 0, 1)>, /* OVC */
+ <RZG2L_PORT_PINMUX(5, 1, 1)>; /* OTG_ID */
+ };
+
+ usb1_pins: usb1 {
+ pinmux = <RZG2L_PORT_PINMUX(42, 0, 1)>, /* VBUS */
+ <RZG2L_PORT_PINMUX(42, 1, 1)>; /* OVC */
+ };
+};
+
diff --git a/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi b/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
index 6f2a8bdfa225..46abb29718cc 100644
--- a/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg2l-smarc.dtsi
@@ -162,133 +162,6 @@
status = "okay";
};
-&pinctrl {
- pinctrl-0 = <&sound_clk_pins>;
- pinctrl-names = "default";
-
- can0_pins: can0 {
- pinmux = <RZG2L_PORT_PINMUX(10, 1, 2)>, /* TX */
- <RZG2L_PORT_PINMUX(11, 0, 2)>; /* RX */
- };
-
- /* SW7 should be at position 2->3 so that GPIO8_CAN0_STB line is activated */
- can0-stb {
- gpio-hog;
- gpios = <RZG2L_GPIO(42, 2) GPIO_ACTIVE_HIGH>;
- output-low;
- line-name = "can0_stb";
- };
-
- can1_pins: can1 {
- pinmux = <RZG2L_PORT_PINMUX(12, 1, 2)>, /* TX */
- <RZG2L_PORT_PINMUX(13, 0, 2)>; /* RX */
- };
-
- /* SW8 should be at position 2->3 so that GPIO9_CAN1_STB line is activated */
- can1-stb {
- gpio-hog;
- gpios = <RZG2L_GPIO(42, 3) GPIO_ACTIVE_HIGH>;
- output-low;
- line-name = "can1_stb";
- };
-
- i2c0_pins: i2c0 {
- pins = "RIIC0_SDA", "RIIC0_SCL";
- input-enable;
- };
-
- i2c1_pins: i2c1 {
- pins = "RIIC1_SDA", "RIIC1_SCL";
- input-enable;
- };
-
- i2c3_pins: i2c3 {
- pinmux = <RZG2L_PORT_PINMUX(18, 0, 3)>, /* SDA */
- <RZG2L_PORT_PINMUX(18, 1, 3)>; /* SCL */
- };
-
- scif0_pins: scif0 {
- pinmux = <RZG2L_PORT_PINMUX(38, 0, 1)>, /* TxD */
- <RZG2L_PORT_PINMUX(38, 1, 1)>; /* RxD */
- };
-
- scif2_pins: scif2 {
- pinmux = <RZG2L_PORT_PINMUX(48, 0, 1)>, /* TxD */
- <RZG2L_PORT_PINMUX(48, 1, 1)>, /* RxD */
- <RZG2L_PORT_PINMUX(48, 3, 1)>, /* CTS# */
- <RZG2L_PORT_PINMUX(48, 4, 1)>; /* RTS# */
- };
-
- sd1-pwr-en-hog {
- gpio-hog;
- gpios = <RZG2L_GPIO(39, 2) GPIO_ACTIVE_HIGH>;
- output-high;
- line-name = "sd1_pwr_en";
- };
-
- sdhi1_pins: sd1 {
- sd1_data {
- pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
- power-source = <3300>;
- };
-
- sd1_ctrl {
- pins = "SD1_CLK", "SD1_CMD";
- power-source = <3300>;
- };
-
- sd1_mux {
- pinmux = <RZG2L_PORT_PINMUX(19, 0, 1)>; /* SD1_CD */
- };
- };
-
- sdhi1_pins_uhs: sd1_uhs {
- sd1_data_uhs {
- pins = "SD1_DATA0", "SD1_DATA1", "SD1_DATA2", "SD1_DATA3";
- power-source = <1800>;
- };
-
- sd1_ctrl_uhs {
- pins = "SD1_CLK", "SD1_CMD";
- power-source = <1800>;
- };
-
- sd1_mux_uhs {
- pinmux = <RZG2L_PORT_PINMUX(19, 0, 1)>; /* SD1_CD */
- };
- };
-
- sound_clk_pins: sound_clk {
- pins = "AUDIO_CLK1", "AUDIO_CLK2";
- input-enable;
- };
-
- spi1_pins: spi1 {
- pinmux = <RZG2L_PORT_PINMUX(44, 0, 1)>, /* CK */
- <RZG2L_PORT_PINMUX(44, 1, 1)>, /* MOSI */
- <RZG2L_PORT_PINMUX(44, 2, 1)>, /* MISO */
- <RZG2L_PORT_PINMUX(44, 3, 1)>; /* SSL */
- };
-
- ssi0_pins: ssi0 {
- pinmux = <RZG2L_PORT_PINMUX(45, 0, 1)>, /* BCK */
- <RZG2L_PORT_PINMUX(45, 1, 1)>, /* RCK */
- <RZG2L_PORT_PINMUX(45, 2, 1)>, /* TXD */
- <RZG2L_PORT_PINMUX(45, 3, 1)>; /* RXD */
- };
-
- usb0_pins: usb0 {
- pinmux = <RZG2L_PORT_PINMUX(4, 0, 1)>, /* VBUS */
- <RZG2L_PORT_PINMUX(5, 0, 1)>, /* OVC */
- <RZG2L_PORT_PINMUX(5, 1, 1)>; /* OTG_ID */
- };
-
- usb1_pins: usb1 {
- pinmux = <RZG2L_PORT_PINMUX(42, 0, 1)>, /* VBUS */
- <RZG2L_PORT_PINMUX(42, 1, 1)>; /* OVC */
- };
-};
-
&scif0 {
pinctrl-0 = <&scif0_pins>;
pinctrl-names = "default";
--
2.17.1
