From: Alexandru Tachici <alexandru.tachici@xxxxxxxxxx> The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for industrial Ethernet applications and is compliant with the IEEE 802.3cg Ethernet standard for long reach 10 Mb/s Single Pair Ethernet. The ADIN1100 uses Auto-Negotiation capability in accordance with IEEE 802.3 Clause 98, providing a mechanism for exchanging information between PHYs to allow link partners to agree to a common mode of operation. The concluded operating mode is the transmit amplitude mode and master/slave preference common across the two devices. Both device and LP advertise their ability and request for increased transmit at: - BASE-T1 autonegotiation advertisement register [47:32]\ Clause 45.2.7.21 of Standard 802.3 - BIT(13) - 10BASE-T1L High Level Transmit Operating Mode Ability - BIT(12) - 10BASE-T1L High Level Transmit Operating Mode Request For 2.4 Vpp (high level transmit) operation, both devices need to have the High Level Transmit Operating Mode Ability bit set, and only one of them needs to have the High Level Transmit Operating Mode Request bit set. Otherwise 1.0 Vpp transmit level will be used. Settings for eth1: Supported ports: [ TP MII ] Supported link modes: 10baseT1L/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT1L/Full Advertised pause frame use: No Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT1L/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 10Mb/s Duplex: Full Auto-negotiation: on master-slave cfg: preferred slave master-slave status: slave Port: Twisted Pair PHYAD: 0 Transceiver: external MDI-X: Unknown Link detected: yes SQI: 7/7 1. Add basic support for ADIN1100. Alexandru Ardelean (1): net: phy: adin1100: Add initial support for ADIN1100 industrial PHY 1. Added 10baset-T1L link modes. 2. Added 10-BasetT1L registers. 3. Added Base-T1 auto-negotiation registers. For Base-T1 these registers decide master/slave status and TX voltage of the device and link partner. 4. Added 10BASE-T1L support in phy-c45.c. Now genphy functions will call Base-T1 functions where registers don't match, like the auto-negotiation ones. 5. Convert MSE to SQI using a predefined table and allow user access through ethtool. 6. DT bindings for the 2.4 Vpp transmit mode. Alexandru Ardelean (1): net: phy: adin1100: Add initial support for ADIN1100 industrial PHY Alexandru Tachici (6): ethtool: Add 10base-T1L link mode entry net: phy: Add 10-BaseT1L registers net: phy: Add BaseT1 auto-negotiation registers net: phy: Add 10BASE-T1L support in phy-c45 net: phy: adin1100: Add SQI support dt-bindings: net: phy: Add 10-baseT1L 2.4 Vpp Changelog: V3 -> V4: - fixed kernel-doc errors - ETHTOOL_LINK_MODE_10baseT1L_Full_BIT of phydev->supported is now set inside in genphy_c45_pma_read_abilities() call if device supports 10BASE-T1L - fix 802.3 reg defines comments (kept documentation wording instead) - fix 0x0010 advertise master preference (T4) (instead of 0x0080) - added genphy_c45_baset1_read_lpa to phy-c45.c, will get called from genphy_c45_read_lpa, if the phy supports BASE-T1 advertisement register - added genphy_c45_baset1_read_link to phy-c45.c, will get called from genphy_c45_read_link, if the phy supports BASE-T1 registers - replaced adin_read_lpa from adin1100.c with genphy_c45_read_lpa - added support for BASE-T1 master/slave status and advertising in phy-c45.c - dropped yaml file (no need for it) no vendor specific properties to be added in the DT - moved most of the BASE-T1 specific code from adin1100.c to gen-phy-c45 - changed an-10base-t1l-2.4vpp property name to phy-10base-t1l-2.4vpp - in adin1100.c, when auto-negotiation is disabled, if increased transmit property is set in DT (phy-10base-t1l-2.4vpp = <1>) force Tx PHY level to 2.4 vpp otherwise force to 1.0 vpp. - added 10BASE-T1L PMA control mdio.h .../devicetree/bindings/net/ethernet-phy.yaml | 9 + drivers/net/phy/Kconfig | 7 + drivers/net/phy/Makefile | 1 + drivers/net/phy/adin1100.c | 299 ++++++++++++++++++ drivers/net/phy/phy-c45.c | 283 ++++++++++++++++- drivers/net/phy/phy-core.c | 3 +- include/linux/mdio.h | 70 ++++ include/uapi/linux/ethtool.h | 1 + include/uapi/linux/mdio.h | 75 +++++ net/ethtool/common.c | 3 + 10 files changed, 744 insertions(+), 7 deletions(-) create mode 100644 drivers/net/phy/adin1100.c -- 2.25.1
