On Fri, Aug 22, 2014 at 10:54:50AM -0700, Sean Paul wrote: > On Thu, Aug 7, 2014 at 10:14 AM, Sean Paul <seanpaul@xxxxxxxxxxxx> wrote: > > > On Thu, Aug 7, 2014 at 4:34 AM, Thierry Reding <thierry.reding@xxxxxxxxx> > > wrote: > > > On Thu, Aug 07, 2014 at 02:11:46AM -0400, Sean Paul wrote: > > >> When calibrating the mipi phy, also include the clock lanes > > >> in the calibration. > > >> > > >> Signed-off-by: Sean Paul <seanpaul@xxxxxxxxxxxx> > > >> --- > > >> drivers/gpu/host1x/mipi.c | 70 > > +++++++++++++++++++++++++++++++++++++---------- > > >> 1 file changed, 56 insertions(+), 14 deletions(-) > > >> > > >> diff --git a/drivers/gpu/host1x/mipi.c b/drivers/gpu/host1x/mipi.c > > >> index 0af2892..80578dc 100644 > > >> --- a/drivers/gpu/host1x/mipi.c > > >> +++ b/drivers/gpu/host1x/mipi.c > > >> @@ -49,10 +49,18 @@ > > >> #define MIPI_CAL_CONFIG_DSIC 0x10 > > >> #define MIPI_CAL_CONFIG_DSID 0x11 > > >> > > >> +#define MIPI_CAL_CONFIG_DSIAB_CLK 0x19 > > >> +#define MIPI_CAL_CONFIG_DSICD_CLK 0x1a > > >> +#define MIPI_CAL_CONFIG_CSIAB_CLK 0x1b > > >> +#define MIPI_CAL_CONFIG_CSICD_CLK 0x1c > > >> +#define MIPI_CAL_CONFIG_CSIE_CLK 0x1d > > >> + > > > > > > These registers don't seem to exist on Tegra114 and earlier. It also > > > seems like MIPI_CAL_CONFIG_DSIC and MIPI_CAL_CONFIG_DSID no longer exist > > > on Tegra124 and later. And CSIC and CSID seem to be shared with DSIB > > > (channel A and B) now. > > > > > > So I think we'll need something more elaborate than this. It should be > > > differentiating between SoC revisions to allow checking for valid pad > > > selection when calibrating. > > > > > > > Yeah, definitely now that you point that out, we'll need something > > better. I've altered the patch so the regs available depends on > > compatible value. I'll wait on the following before re-posting. > > > > > I'll see if I can find out what's up with the change between Tegra114 > > > and Tegra124 regarding the DSIC and DSID pads. It looks to me like they > > > were merged to match the DSIA and DSIB controllers, whereas before DSIA > > > and DSIB were used for controller DSIA and DSIC and DSID were used for > > > controller DSIB. > > > > > > > Thanks for checking in on this. It would be useful to know which clock > > lanes need to be configured for which pads. The documentation isn't > > particularly good on this, so it's possible that my mapping between > > data lane/clock lane in the modules array is incorrect. > > > > > Hi Thierry, > Any update on this? I don't have any definitive answers yet, but from doing a bit of research it seems that the D-PHY for DSI (and CSI) can be configured to run in two modes, one where the 4 lanes are used as a single channel and another where they can drive two channels. My understanding is that that is what the channels refer to. That is, the D-PHY for controller DSI is calibrated using the MIPI_CAL_CONFIG_DSIA register (0x0e/0x38) for data lanes and MIPI_CAL_CONFIG_DSIA_A (0x19/0x64) and MIPI_CAL_CONFIG_DSIA_B (0x1a/0x68) for clock lanes. For controller DSIB the registers are MIPI_CAL_CONFIG_DSIB (0x0f/0x3c) and MIPI_CAL_CONFIG_DSIB_A (0x1b/0x6c) as well as MIPI_CAL_CONFIG_DSIB_B (0x1c/0x70). The second controller also shares the pads with CSIC and CSID. As for the difference between Tegra114 and Tegra124 it seems that clock lane calibration is new in Tegra124 (or perhaps it was done as part of the data lane calibration on Tegra114), but DSIA and DSIB on Tegra114 refer to DSI channels A and B, whereas DSIC and DSID refer to channels A and B of DSIB. The above is still mostly guesswork, though perhaps more educated than before. I've filed an internal bug to get confirmation from some of our hardware engineers and clarify this in the TRM. I'll let you know when I have more information. Thierry
Attachment:
pgpsJfYs7a_lB.pgp
Description: PGP signature
