Add documentation for ad3552r Signed-off-by: Mihail Chindris <mihail.chindris@xxxxxxxxxx> --- .../bindings/iio/dac/adi,ad3552r.yaml | 190 ++++++++++++++++++ 1 file changed, 190 insertions(+) create mode 100644 Documentation/devicetree/bindings/iio/dac/adi,ad3552r.yaml diff --git a/Documentation/devicetree/bindings/iio/dac/adi,ad3552r.yaml b/Documentation/devicetree/bindings/iio/dac/adi,ad3552r.yaml new file mode 100644 index 000000000000..c6999bb4c7a4 --- /dev/null +++ b/Documentation/devicetree/bindings/iio/dac/adi,ad3552r.yaml @@ -0,0 +1,190 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +# Copyright 2020 Analog Devices Inc. +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/iio/dac/adi,ad3552r.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Analog Devices AD2552R DAC device driver + +maintainers: + - Mihail Chindris <mihail.chindris@xxxxxxxxxx> + +description: | + Bindings for the Analog Devices AD3552R DAC device and similar. + Datasheet can be found here: + https://www.analog.com/media/en/technical-documentation/data-sheets/ad3542r.pdf + https://www.analog.com/media/en/technical-documentation/data-sheets/ad3552r.pdf +properties: + compatible: + enum: + - adi,ad3542r + - adi,ad3552r + + reg: + maxItems: 1 + + spi-max-frequency: + maximum: 30000000 + + reset-gpios: + maxItems: 1 + + ldac-gpios: + description: | + LDAC pin to be used as a hardware trigger to update the DAC channels. + maxItems: 1 + + vref-supply: + description: + The regulator to use as an external reference. If it does not exists the + internal reference will be used. External reference must be 2.5V + + adi,vref-out-en: + description: Vref I/O driven by internal vref to 2.5V. If not set, Vref pin + will be floating. + type: boolean + + adi,sdo-drive-strength: + description: | + Configure SDIO0 and SDIO1 strength levels: + - 0: low SDO drive strength. + - 1: medium low SDO drive strength. + - 2: medium high SDO drive strength. + - 3: high SDO drive strength + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + +patternProperties: + "^channel@([0-1])$": + type: object + description: Configurations of the DAC Channels + properties: + reg: + description: Channel number + enum: [0, 1] + + custom-output-range-config: + type: object + description: Configuration of custom range when + adi,output-range-microvolt is not present. + The formulas for calculation the output voltages are + Vout_fs = 2.5 + [(GainN + Offset/1024) * 2.5 * Rfbx * 1.03] + Vout_zs = 2.5 - [(GainP + Offset/1024) * 2.5 * Rfbx * 1.03] + properties: + adi,gain-offset: + description: Gain offset used in the above formula + $ref: /schemas/types.yaml#/definitions/int32 + maximum: 511 + minimum: -511 + adi,gain-scaling-p-inv-log2: + description: GainP = 1 / ( 2 ^ adi,gain-scaling-p-inv-log2) + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + adi,gain-scaling-n-inv-log2: + description: GainN = 1 / ( 2 ^ adi,gain-scaling-n-inv-log2) + $ref: /schemas/types.yaml#/definitions/uint32 + enum: [0, 1, 2, 3] + adi,rfb-ohms: + description: Feedback Resistor + required: + - adi,gain-offset + - adi,gain-scaling-p-inv-log2 + - adi,gain-scaling-n-inv-log2 + - adi,rfb-ohms + required: + - reg + + oneOf: + # If adi,output-range-microvolt is missing, + # custom-output-range-config must be used + - required: + - adi,output-range-microvolt + - required: + - custom-output-range-config + +allOf: + - if: + properties: + compatible: + contains: + const: adi,ad3542r + then: + patternProperties: + "^channel@([0-1])$": + type: object + properties: + adi,output-range-microvolt: + description: | + Voltage output range of the channel as <minimum, maximum> + Required connections: + Rfb1x for: 0 to 2.5 V; 0 to 3V; 0 to 5 V; + Rfb2x for: 0 to 10 V; 2.5 to 7.5V; -5 to 5 V; + oneOf: + - items: + - const: 0 + - enum: [2500000, 3000000, 5000000, 10000000] + - items: + - const: -2500000 + - const: 7500000 + - items: + - const: -5000000 + - const: 5000000 + required: + - adi,output-range-microvolt + - if: + properties: + compatible: + contains: + const: adi,ad3552r + then: + patternProperties: + "^channel@([0-1])$": + type: object + properties: + adi,output-range-microvolt: + description: | + Voltage output range of the channel as <minimum, maximum> + Required connections: + Rfb1x for: 0 to 2.5 V; 0 to 5 V; + Rfb2x for: 0 to 10 V; -5 to 5 V; + Rfb4x for: -10 to 10V + oneOf: + - items: + - const: 0 + - enum: [2500000, 5000000, 10000000] + - items: + - const: -5000000 + - const: 5000000 + - items: + - const: -10000000 + - const: 10000000 + +required: + - compatible + - reg + - spi-max-frequency + +additionalProperties: false + +examples: + - | + ad3552r { + compatible = "adi,ad3552r"; + reg = <0>; + spi-max-frequency = <20000000>; + channel@0 { + reg = <0>; + adi,output-range-microvolt = <0 10000000>; + }; + channel@1 { + reg = <1>; + custom-output-range-config { + adi,gain-offset = <5>; + adi,gain-scaling-p-inv-log2 = <1>; + adi,gain-scaling-n-inv-log2 = <2>; + adi,rfb-ohms = <1>; + }; + }; + }; +... -- 2.27.0
