With the Hantro G1 and G2 now setup to run independently, update the device tree to enable it again. This requires the vpu-blk-ctrl node to be configured, and the clock-parents and clock-rates for the various VPU's to be moved into the pgc_vpu because they cannot get re-parented once enabled, and the pgc_vpu is the highest in the chain. Signed-off-by: Adam Ford <aford173@xxxxxxxxx> --- arch/arm64/boot/dts/freescale/imx8mq.dtsi | 69 +++++++++++++++-------- 1 file changed, 45 insertions(+), 24 deletions(-) This clock rates and parents were moved to the pgc_vpu node because the vpu-blk-ctrl is expecting certain clocks to be operational, and they cannot be re-parented once they are runing. The datasheet and the TRM both show different potential clock rates for the G2 CODEC. It could be as low as 300MHZ or as high as 650 depending on what document is read, and the operating voltage of the hardware. Because of the uncertainty, the clock rates proposed here match those in NXP's 5.10 Release. https://source.codeaurora.org/external/imx/linux-imx/tree/arch/arm64/boot/dts/freescale/imx8mq.dtsi?h=lf-5.10.y diff --git a/arch/arm64/boot/dts/freescale/imx8mq.dtsi b/arch/arm64/boot/dts/freescale/imx8mq.dtsi index 972766b67a15..0d3053bbfb2c 100644 --- a/arch/arm64/boot/dts/freescale/imx8mq.dtsi +++ b/arch/arm64/boot/dts/freescale/imx8mq.dtsi @@ -711,7 +711,21 @@ pgc_gpu: power-domain@5 { pgc_vpu: power-domain@6 { #power-domain-cells = <0>; reg = <IMX8M_POWER_DOMAIN_VPU>; - clocks = <&clk IMX8MQ_CLK_VPU_DEC_ROOT>; + clocks = <&clk IMX8MQ_CLK_VPU_DEC_ROOT>, + <&clk IMX8MQ_CLK_VPU_G1_ROOT>, + <&clk IMX8MQ_CLK_VPU_G2_ROOT>; + assigned-clocks = <&clk IMX8MQ_CLK_VPU_G1>, + <&clk IMX8MQ_CLK_VPU_G2>, + <&clk IMX8MQ_CLK_VPU_BUS>, + <&clk IMX8MQ_VPU_PLL_BYPASS>; + assigned-clock-parents = <&clk IMX8MQ_VPU_PLL_OUT>, + <&clk IMX8MQ_VPU_PLL_OUT>, + <&clk IMX8MQ_SYS1_PLL_800M>, + <&clk IMX8MQ_VPU_PLL>; + assigned-clock-rates = <600000000>, + <600000000>, + <800000000>, + <0>; }; pgc_disp: power-domain@7 { @@ -1432,30 +1446,37 @@ usb3_phy1: usb-phy@382f0040 { status = "disabled"; }; - vpu: video-codec@38300000 { - compatible = "nxp,imx8mq-vpu"; - reg = <0x38300000 0x10000>, - <0x38310000 0x10000>, - <0x38320000 0x10000>; - reg-names = "g1", "g2", "ctrl"; - interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, - <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; - interrupt-names = "g1", "g2"; + vpu_g1: video-codec@38300000 { + compatible = "nxp,imx8mq-vpu-g1"; + reg = <0x38300000 0x10000>; + reg-names = "g1"; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "g1"; + clocks = <&clk IMX8MQ_CLK_VPU_G1_ROOT>; + clock-names = "g1"; + power-domains = <&vpu_blk_ctrl IMX8MQ_VPUBLK_PD_G1>; + }; + + vpu_g2: video-codec@38310000 { + compatible = "nxp,imx8mq-vpu-g2"; + reg = <0x38310000 0x10000>; + reg-names = "g2"; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>; + interrupt-names = "g2"; + clocks = <&clk IMX8MQ_CLK_VPU_G2_ROOT>; + clock-names = "g2"; + power-domains = <&vpu_blk_ctrl IMX8MQ_VPUBLK_PD_G2>; + }; + + vpu_blk_ctrl: blk-ctrl@38320000 { + compatible = "fsl,imx8mq-vpu-blk-ctrl", "syscon"; + reg = <0x38320000 0x100>; + power-domains = <&pgc_vpu>, <&pgc_vpu>, <&pgc_vpu>; + power-domain-names = "bus", "g1", "g2"; clocks = <&clk IMX8MQ_CLK_VPU_G1_ROOT>, - <&clk IMX8MQ_CLK_VPU_G2_ROOT>, - <&clk IMX8MQ_CLK_VPU_DEC_ROOT>; - clock-names = "g1", "g2", "bus"; - assigned-clocks = <&clk IMX8MQ_CLK_VPU_G1>, - <&clk IMX8MQ_CLK_VPU_G2>, - <&clk IMX8MQ_CLK_VPU_BUS>, - <&clk IMX8MQ_VPU_PLL_BYPASS>; - assigned-clock-parents = <&clk IMX8MQ_VPU_PLL_OUT>, - <&clk IMX8MQ_VPU_PLL_OUT>, - <&clk IMX8MQ_SYS1_PLL_800M>, - <&clk IMX8MQ_VPU_PLL>; - assigned-clock-rates = <600000000>, <600000000>, - <800000000>, <0>; - power-domains = <&pgc_vpu>; + <&clk IMX8MQ_CLK_VPU_G2_ROOT>; + clock-names = "g1", "g2"; + #power-domain-cells = <1>; }; pcie0: pcie@33800000 { -- 2.32.0
