Re: [PATCH v11 0/3] Add AD74413R driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun,  5 Dec 2021 13:40:42 +0200
Cosmin Tanislav <demonsingur@xxxxxxxxx> wrote:

> V1 -> V2
>  * sign off using company email
> 
> V2 -> V3
>  * replace gpo config firmware flag with flag specifying whether gpo is in
>    comparator mode
>  * create two separate gpiochips, one output-only gpiochip for GPO pins not
>    in comparator mode and one input-only for the value of digital input
>    channels
>  * wire up all gpo functionalities using pinconf
>  * keep number of characters per line under 80
>  * rework locking
>  * do not invalidate other chip revisions
>  * do not set indio device parent
>  * print probe error for refin regulator
>  * move conversion from range register value to range / offset / raw offset
>    into separate function
>  * module.h -> mod_devicetable.h
>  * use generic firmware interface functions
>  * add comment regarding cache alignment
>  * add comment regarding ADC channels buffered read setup
>  * un-inline comment regarding 100us delay for conversion start
>  * inline return statements
>  * remove assignments to val2 where not necessary
>  * local_channels -> chans
>  * index -> i
>  * channel_config -> config
>  * IIO_ALTVOLTAGE -> IIO_VOLTAGE
>  * .info_mask_shared_by_type_available -> .info_mask_separate_available
>  * remove unlikely probe error messages
>  * use an array indexed by channel function for retrieving iio channels
>  * count iio channels while parsing
>  * move HART rate rejection outside of setter
>  * move channel function validation outside of setter
>  * use SPI messages for read and write
>  * validate DAC code earlier
>  * simplify switches to only handle existing iio channels
>  * pass indio_dev into functions needing access to it
>  * pass spi into devm_regmap_init
>  * dt-bindings: sort compatibles
>  * dt-bindings: remove driver word from description
>  * dt-bindings: remove refin supply description
>  * dt-bindings: specify channel function default value
>  * dt-bindings: remove maxItems from scalar value
> 
> V3 -> v4
>  * remove double gpo from macro name
>  * reset at probe
>  * config -> chip_info and store chip name inside chip info
>  * cacheline align every DMA buffer
>  * simplify generation of adc samples message by caching xfer, tx_buf and
>    rx_buf
>  * use mask itself for writing the value of channel enable and gpo data
>  * move reg read and write transfers to the same buffers and use local
>    variables for transfers
>  * merge the two for loops handling gpio configuration
>  * let firmware decide irq edge
>  * remove INDIO_BUFFER_SOFTWARE already set by iio framework
>  * do not set trigger device parent
>  * return dev_err_probe for regulator error case
>  * do not set cs_change to 0 when not needed
>  * do not set spi device drvdata as it is not needed
>  * fix bug regarding wrong channels being created for resistance input,
>    digital input, and current input with hart
>  * use voltage input channels spec for high impedance mode
>  * put () around macro parameters
>  * merge AD74413R_CHANNEL macro into its uses
>  * remove unused switch case scope
>  * inline return IIO_VAL_INT
>  * use {get,put}_unaligned_be16
>  * use proper types for reg and val
>  * move default case handling into switch statements
>  * pass driver state into regmap functions
>  * use genmask for generating a 16bit max value
>  * alphanumeric order for part numbers
>  * dt-bindings: remove $ref from ohms value
> 
> V4 -> V5
>  * dt-bindings: include headers necessary
>  * dt-bindings: add IRQ_TYPE_EDGE_FALLING to interrupt flags
>  * dt-bindings: ohm -> ohms
>  * dt-bindings: spi0 -> spi
> 
> V5 -> V6
>  * fix warnings regarding overflows
> 
> V6 -> V7
>  * remove extra cache-line alignment
>  * adi,rsense-resistance-ohms -> shunt-resistor-micro-ohms
>  * dt-bindings: add product page links
> 
> V7 -> V8
>  * also check DAC code lower bound
>  * fix checkpath --strict complaints
>  * add comment regarding mutex lock usage
>  * propagate error when converting adc result to resistance
> 
> V8 -> V9
>  * fix spelling mistake
>  * undo propagate error when converting adc result to resistance
>  * return void from adc result to resistance function
>  * limit max adc value when doing resistance calculation to avoid
>    a potential division-by-zero case
> 
> V9 -> V10
>  * pick up Reviewed-By tags
>  * fix odd alignment in header
>  * add dev_err_probe to irq request error path
> 
> V10 -> V11
>  * fix compile error

Applied with one minor tweak to regmap_config which should have been marked
static and turned up in my build tests.

Applied to the togreg branch of iio.git and pushed out initially as testing
to see if 0-day finds anything.

Thanks,

Jonathan


> 
> Cosmin Tanislav (3):
>   iio: add addac subdirectory
>   dt-bindings: iio: add AD74413R
>   iio: addac: add AD74413R driver
> 
>  .../bindings/iio/addac/adi,ad74413r.yaml      |  158 ++
>  MAINTAINERS                                   |    9 +
>  drivers/iio/Kconfig                           |    1 +
>  drivers/iio/Makefile                          |    1 +
>  drivers/iio/addac/Kconfig                     |   20 +
>  drivers/iio/addac/Makefile                    |    7 +
>  drivers/iio/addac/ad74413r.c                  | 1475 +++++++++++++++++
>  include/dt-bindings/iio/addac/adi,ad74413r.h  |   21 +
>  8 files changed, 1692 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/iio/addac/adi,ad74413r.yaml
>  create mode 100644 drivers/iio/addac/Kconfig
>  create mode 100644 drivers/iio/addac/Makefile
>  create mode 100644 drivers/iio/addac/ad74413r.c
>  create mode 100644 include/dt-bindings/iio/addac/adi,ad74413r.h
> 




[Index of Archives]     [Device Tree Compilter]     [Device Tree Spec]     [Linux Driver Backports]     [Video for Linux]     [Linux USB Devel]     [Linux PCI Devel]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Yosemite Backpacking]


  Powered by Linux