> -----Original Message-----
> From: Vinod Koul <vkoul@xxxxxxxxxx>
> Sent: Thursday, December 2, 2021 12:30 PM
> To: Hongxing Zhu <hongxing.zhu@xxxxxxx>
> Cc: l.stach@xxxxxxxxxxxxxx; bhelgaas@xxxxxxxxxx;
> lorenzo.pieralisi@xxxxxxx; Marcel Ziswiler
> <marcel.ziswiler@xxxxxxxxxxx>; tharvey@xxxxxxxxxxxxx;
> kishon@xxxxxx; robh@xxxxxxxxxx; galak@xxxxxxxxxxxxxxxxxxx;
> shawnguo@xxxxxxxxxx; linux-phy@xxxxxxxxxxxxxxxxxxx;
> devicetree@xxxxxxxxxxxxxxx; linux-pci@xxxxxxxxxxxxxxx;
> linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx;
> kernel@xxxxxxxxxxxxxx; dl-linux-imx <linux-imx@xxxxxxx>
> Subject: Re: [PATCH v6 5/8] phy: freescale: pcie: Initialize the imx8 pcie
> standalone phy driver
>
> On 18-11-21, 09:54, Richard Zhu wrote:
> > Add the standalone i.MX8 PCIe PHY driver.
> >
> > Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx>
> > Tested-by: Marcel Ziswiler <marcel.ziswiler@xxxxxxxxxxx>
> > Reviewed-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
> > Tested-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
> > ---
> > drivers/phy/freescale/Kconfig | 9 +
> > drivers/phy/freescale/Makefile | 1 +
> > drivers/phy/freescale/phy-fsl-imx8m-pcie.c | 237
> > +++++++++++++++++++++
> > 3 files changed, 247 insertions(+)
> > create mode 100644 drivers/phy/freescale/phy-fsl-imx8m-pcie.c
> >
> > diff --git a/drivers/phy/freescale/Kconfig
> > b/drivers/phy/freescale/Kconfig index 320630ffe3cd..e821498b1f7f
> > 100644
> > --- a/drivers/phy/freescale/Kconfig
> > +++ b/drivers/phy/freescale/Kconfig
> > @@ -14,3 +14,12 @@ config PHY_MIXEL_MIPI_DPHY
> > help
> > Enable this to add support for the Mixel DSI PHY as found
> > on NXP's i.MX8 family of SOCs.
> > +
> > +config PHY_FSL_IMX8M_PCIE
> > + tristate "Freescale i.MX8M PCIE PHY"
> > + depends on OF && HAS_IOMEM
> > + select GENERIC_PHY
> > + default ARCH_MXC && ARM64
>
> Why should this be default ? We dont do that for new drivers.. You may
> add this to respective config file though...
>
[Richard Zhu] First of all, thanks a lot for your review comments.
I see, and would remove the default in the kconfig.
> > +static int imx8_pcie_phy_init(struct phy *phy) {
> > + int ret;
> > + u32 val, pad_mode;
> > + struct imx8_pcie_phy *imx8_phy = phy_get_drvdata(phy);
> > +
> > + reset_control_assert(imx8_phy->reset);
> > +
> > + pad_mode = imx8_phy->refclk_pad_mode;
> > + /* Set AUX_EN_OVERRIDE 1'b0, when the CLKREQ# isn't hooked */
> > + regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > + IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE,
> > + imx8_phy->clkreq_unused ?
> > + 0 : IMX8MM_GPR_PCIE_AUX_EN_OVERRIDE);
> > + regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > + IMX8MM_GPR_PCIE_AUX_EN,
> > + IMX8MM_GPR_PCIE_AUX_EN);
> > + regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > + IMX8MM_GPR_PCIE_POWER_OFF, 0);
> > + regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > + IMX8MM_GPR_PCIE_SSC_EN, 0);
> > +
> > + regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > + IMX8MM_GPR_PCIE_REF_CLK_SEL,
> > + pad_mode == IMX8_PCIE_REFCLK_PAD_INPUT ?
> > + IMX8MM_GPR_PCIE_REF_CLK_EXT :
> > + IMX8MM_GPR_PCIE_REF_CLK_PLL);
> > + usleep_range(100, 200);
> > +
> > + /* Do the PHY common block reset */
> > + regmap_update_bits(imx8_phy->iomuxc_gpr, IOMUXC_GPR14,
> > + IMX8MM_GPR_PCIE_CMN_RST,
> > + IMX8MM_GPR_PCIE_CMN_RST);
> > + usleep_range(200, 500);
> > +
> > +
>
> No multi blank line please
[Richard Zhu] Ok, got that.
>
> > +static struct platform_driver imx8_pcie_phy_driver = {
> > + .probe = imx8_pcie_phy_probe,
> > + .driver = {
> > + .name = "imx8-pcie-phy",
> > + .of_match_table = imx8_pcie_phy_of_match,
> > + }
> > +};
> > +module_platform_driver(imx8_pcie_phy_driver);
> > +
> > +MODULE_DESCRIPTION("FSL IMX8 PCIE PHY driver");
> > +MODULE_LICENSE("GPL");
>
> This does not match the SPDX tag you have given
[Richard Zhu] Should the "GPL v2" correct one?
If yes, I would change it this way later.
Thanks.
Best Regards
Richard
>
> --
> ~Vinod
