On Mon, Nov 22, 2021 at 10:20:50PM -0800, Tanmay Shah wrote:
> This driver enables r5f dual core Real time Processing Unit subsystem
> available on Xilinx Zynq Ultrascale MPSoC Platform. RPU subsystem
> (cluster) can be configured in different modes e.g. split mode in which
> two r5f cores work independent of each other and lock-step mode in which
> both r5f cores execute same code clock-for-clock and notify if the
> result is different.
>
> The Xilinx r5 Remoteproc Driver boots the RPU cores via calls to the Xilinx
> Platform Management Unit that handles the R5 configuration, memory access
> and R5 lifecycle management. The interface to this manager is done in this
> driver via zynqmp_pm_* function calls.
>
> Signed-off-by: Ben Levinsky <ben.levinsky@xxxxxxxxxx>
> Signed-off-by: Tanmay Shah <tanmay.shah@xxxxxxxxxx>
> ---
> drivers/remoteproc/Kconfig | 12 +
> drivers/remoteproc/Makefile | 1 +
> drivers/remoteproc/xlnx_r5_remoteproc.c | 959 ++++++++++++++++++++++++
> 3 files changed, 972 insertions(+)
> create mode 100644 drivers/remoteproc/xlnx_r5_remoteproc.c
...and this patch gives me complation warnings:
CC drivers/remoteproc/xlnx_r5_remoteproc.o
kernel-review/drivers/remoteproc/xlnx_r5_remoteproc.c: In function ‘add_tcm_carveout_lockstep_mode’:
kernel-review/drivers/remoteproc/xlnx_r5_remoteproc.c:412:28: warning: unused variable ‘cluster’ [-Wunused-variable]
412 | struct zynqmp_r5_cluster *cluster;
| ^~~~~~~
kernel-review/drivers/remoteproc/xlnx_r5_remoteproc.c:411:26: warning: unused variable ‘parent_pdev’ [-Wunused-variable]
411 | struct platform_device *parent_pdev;
| ^~~~~~~~~~~
The above leads me to believe this patchset was not compiled before it was sent
out.
Being new to this I can understand that checkpatch.pl was omitted (albeit amply
documented) but obvious compilation warnings can't be excused. As such I
am dropping this set and will not review another version until January.
Mathieu
>
> diff --git a/drivers/remoteproc/Kconfig b/drivers/remoteproc/Kconfig
> index f30d00a3aabe..27f66910d8d3 100644
> --- a/drivers/remoteproc/Kconfig
> +++ b/drivers/remoteproc/Kconfig
> @@ -315,6 +315,18 @@ config TI_K3_R5_REMOTEPROC
> It's safe to say N here if you're not interested in utilizing
> a slave processor.
>
> +config XLNX_R5_REMOTEPROC
> + tristate "Xilinx R5 remoteproc support"
> + depends on PM && ARCH_ZYNQMP
> + depends on ZYNQMP_FIRMWARE
> + select RPMSG_VIRTIO
> + select ZYNQMP_IPI_MBOX
> + help
> + Say y or m here to support Xilinx R5 remote processors via the remote
> + processor framework.
> +
> + It's safe to say N if not interested in using RPU r5f cores.
> +
> endif # REMOTEPROC
>
> endmenu
> diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
> index bb26c9e4ef9c..334a8bed4c14 100644
> --- a/drivers/remoteproc/Makefile
> +++ b/drivers/remoteproc/Makefile
> @@ -35,3 +35,4 @@ obj-$(CONFIG_ST_SLIM_REMOTEPROC) += st_slim_rproc.o
> obj-$(CONFIG_STM32_RPROC) += stm32_rproc.o
> obj-$(CONFIG_TI_K3_DSP_REMOTEPROC) += ti_k3_dsp_remoteproc.o
> obj-$(CONFIG_TI_K3_R5_REMOTEPROC) += ti_k3_r5_remoteproc.o
> +obj-$(CONFIG_XLNX_R5_REMOTEPROC) += xlnx_r5_remoteproc.o
> diff --git a/drivers/remoteproc/xlnx_r5_remoteproc.c b/drivers/remoteproc/xlnx_r5_remoteproc.c
> new file mode 100644
> index 000000000000..c2167fd3869d
> --- /dev/null
> +++ b/drivers/remoteproc/xlnx_r5_remoteproc.c
> @@ -0,0 +1,959 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * ZynqMP R5 Remote Processor driver
> + *
> + */
> +
> +#include <dt-bindings/power/xlnx-zynqmp-power.h>
> +#include <linux/firmware/xlnx-zynqmp.h>
> +#include <linux/interrupt.h>
> +#include <linux/kernel.h>
> +#include <linux/list.h>
> +#include <linux/mailbox_client.h>
> +#include <linux/mailbox/zynqmp-ipi-message.h>
> +#include <linux/module.h>
> +#include <linux/of_address.h>
> +#include <linux/of_platform.h>
> +#include <linux/of_reserved_mem.h>
> +#include <linux/platform_device.h>
> +#include <linux/remoteproc.h>
> +#include <linux/skbuff.h>
> +#include <linux/sysfs.h>
> +
> +#include "remoteproc_internal.h"
> +
> +/* settings for RPU cluster mode */
> +enum zynqmp_r5_cluster_mode {
> + SPLIT_MODE = 0, // RPU cluster mode when cores run as separate processor
> + LOCKSTEP_MODE = 1, // cores execute same code in lockstep,clk-for-clk
> + SINGLE_CPU_MODE = 2, // core0 is held in reset and only core1 runs
> +};
> +
> +/**
> + * struct mem_bank_data - Memory Bank description
> + *
> + * @addr: Start address of memory bank
> + * @size: Size of Memory bank
> + * @pm_domain_id: Power-domains id of memory bank for firmware to turn on/off
> + * @bank_name: name of the bank for remoteproc framework
> + */
> +struct mem_bank_data {
> + phys_addr_t addr;
> + size_t size;
> + enum pm_node_id pm_domain_id;
> + char *bank_name;
> +};
> +
> +static const struct mem_bank_data zynqmp_tcm_banks[] = {
> + {0xffe00000UL, 0x10000UL, PD_R5_0_ATCM, "atcm0"}, /* TCM 64KB each */
> + {0xffe20000UL, 0x10000UL, PD_R5_0_BTCM, "btcm0"},
> + {0xffe90000UL, 0x10000UL, PD_R5_1_ATCM, "atcm1"},
> + {0xffeb0000UL, 0x10000UL, PD_R5_1_BTCM, "btcm1"},
> +};
> +
> +/**
> + * struct zynqmp_r5_core - ZynqMP R5 core structure
> + *
> + * @dev: device of RPU instance
> + * @np: device node of RPU instance
> + * @tcm_bank_count: number TCM banks accessible to this RPU
> + * @tcm_banks: array of each TCM bank data
> + * @res_mem_count: number of Reserved Memory regions per core
> + * @res_mem: array of reserved memory regions
> + * @rproc: rproc handle
> + * @pm_domain_id: RPU CPU power domain id
> + */
> +struct zynqmp_r5_core {
> + struct device *dev;
> + struct device_node *np;
> + int tcm_bank_count;
> + struct mem_bank_data *tcm_banks;
> + int res_mem_count;
> + struct reserved_mem *res_mem;
> + struct rproc *rproc;
> + enum pm_node_id pm_domain_id;
> +};
> +
> +/**
> + * struct zynqmp_r5_cluster - ZynqMP R5 cluster structure
> + *
> + * @dev: r5f subsystem cluster device node
> + * @mode: cluster mode of type zynqmp_r5_cluster_mode
> + * @core_count: number of r5 cores used for this cluster mode
> + * @r5_cores: Array of r5 cores of type struct zynqmp_r5_core
> + */
> +struct zynqmp_r5_cluster {
> + struct device *dev;
> + enum zynqmp_r5_cluster_mode mode;
> + int core_count;
> + struct zynqmp_r5_core *r5_cores;
> +};
> +
> +/*
> + * zynqmp_r5_set_mode - set RPU operation mode
> + *
> + * set RPU operation mode
> + *
> + * Return: 0 for success, negative value for failure
> + */
> +static int zynqmp_r5_set_mode(struct zynqmp_r5_core *r5_core,
> + enum zynqmp_r5_cluster_mode rpu_mode)
> +{
> + enum rpu_tcm_comb tcm_mode;
> + int ret, reg_val;
> +
> + reg_val = (rpu_mode == LOCKSTEP_MODE ? 0 : 1);
> +
> + ret = zynqmp_pm_set_rpu_mode(r5_core->pm_domain_id, reg_val);
> + if (ret < 0) {
> + pr_err("failed to set RPU mode\n");
> + return ret;
> + }
> +
> + tcm_mode = (rpu_mode == LOCKSTEP_MODE) ?
> + PM_RPU_TCM_COMB : PM_RPU_TCM_SPLIT;
> + ret = zynqmp_pm_set_tcm_config(r5_core->pm_domain_id, tcm_mode);
> + if (ret < 0)
> + pr_err("failed to configure TCM\n");
> +
> + return ret;
> +}
> +
> +/*
> + * zynqmp_r5_rproc_start
> + * @rproc: single R5 core's corresponding rproc instance
> + *
> + * Start R5 Core from designated boot address.
> + *
> + * return 0 on success, otherwise non-zero value on failure
> + */
> +static int zynqmp_r5_rproc_start(struct rproc *rproc)
> +{
> + struct zynqmp_r5_core *r5_core = rproc->priv;
> + enum rpu_boot_mem bootmem;
> + int ret;
> +
> + if (!r5_core) {
> + pr_err("can't get r5 core\n");
> + return -EINVAL;
> + }
> +
> + bootmem = (rproc->bootaddr >= 0xFFFC0000) ?
> + PM_RPU_BOOTMEM_HIVEC : PM_RPU_BOOTMEM_LOVEC;
> +
> + dev_dbg(r5_core->dev, "RPU boot addr 0x%llx from %s.", rproc->bootaddr,
> + bootmem == PM_RPU_BOOTMEM_HIVEC ? "OCM" : "TCM");
> +
> + ret = zynqmp_pm_request_wake(r5_core->pm_domain_id, 1,
> + bootmem, ZYNQMP_PM_REQUEST_ACK_NO);
> + if (ret)
> + pr_err("failed to start RPU = %d\n", r5_core->pm_domain_id);
> + return ret;
> +}
> +
> +/*
> + * zynqmp_r5_rproc_stop
> + * @rproc: single R5 core's corresponding rproc instance
> + *
> + * Power down R5 Core.
> + *
> + * return 0 on success, otherwise non-zero value on failure
> + */
> +static int zynqmp_r5_rproc_stop(struct rproc *rproc)
> +{
> + struct zynqmp_r5_core *r5_core = rproc->priv;
> + int ret;
> +
> + ret = zynqmp_pm_force_pwrdwn(r5_core->pm_domain_id,
> + ZYNQMP_PM_REQUEST_ACK_BLOCKING);
> + if (ret)
> + pr_err("failed to stop remoteproc RPU %d\n", ret);
> +
> + return ret;
> +}
> +
> +/*
> + * zynqmp_r5_rproc_mem_map
> + * @rproc: single R5 core's corresponding rproc instance
> + * @mem: mem entry to map
> + *
> + * Callback to map va for memory-region's carveout.
> + *
> + * return 0 on success, otherwise non-zero value on failure
> + */
> +static int zynqmp_r5_rproc_mem_map(struct rproc *rproc,
> + struct rproc_mem_entry *mem)
> +{
> + void __iomem *va;
> +
> + va = ioremap_wc(mem->dma, mem->len);
> + if (IS_ERR_OR_NULL(va))
> + return -ENOMEM;
> +
> + mem->va = (void *)va;
> +
> + return 0;
> +}
> +
> +/*
> + * zynqmp_r5_rproc_mem_unmap
> + * @rproc: single R5 core's corresponding rproc instance
> + * @mem: mem entry to unmap
> + *
> + * Unmap memory-region carveout
> + *
> + * return 0 on success, otherwise non-zero value on failure
> + */
> +static int zynqmp_r5_rproc_mem_unmap(struct rproc *rproc,
> + struct rproc_mem_entry *mem)
> +{
> + iounmap((void __iomem *)mem->va);
> + return 0;
> +}
> +
> +/*
> + * add_mem_regions
> + * @rproc: single R5 core's corresponding rproc instance
> + *
> + * Construct rproc mem carveouts from carveout provided in
> + * memory-region property
> + *
> + * return 0 on success, otherwise non-zero value on failure
> + */
> +static int add_mem_regions(struct rproc *rproc)
> +{
> + struct device *dev;
> + struct rproc_mem_entry *mem;
> + struct reserved_mem *rmem;
> + struct zynqmp_r5_core *r5_core;
> + int i;
> +
> + r5_core = rproc->priv;
> + dev = r5_core->dev;
> +
> + /* Register associated reserved memory regions */
> + for (i = 0; i < r5_core->res_mem_count; i++) {
> + rmem = &r5_core->res_mem[i];
> + mem = rproc_mem_entry_init(dev, NULL,
> + (dma_addr_t)rmem->base,
> + rmem->size, rmem->base,
> + zynqmp_r5_rproc_mem_map,
> + zynqmp_r5_rproc_mem_unmap,
> + rmem->name);
> + if (IS_ERR_OR_NULL(mem))
> + return -ENOMEM;
> +
> + rproc_add_carveout(rproc, mem);
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * zynqmp_r5_rproc_mem_unmap
> + * @rproc: single R5 core's corresponding rproc instance
> + * @mem: mem entry to unmap
> + *
> + * Unmap TCM banks when powering down R5 core.
> + *
> + * return 0 on success, otherwise non-zero value on failure
> + */
> +static int tcm_mem_unmap(struct rproc *rproc, struct rproc_mem_entry *mem)
> +{
> + struct zynqmp_r5_core *r5_core;
> + int i;
> + enum pm_node_id pm_domain_id;
> +
> + r5_core = rproc->priv;
> + if (!r5_core) {
> + pr_err("r5 core is not available\n");
> + return -EINVAL;
> + }
> +
> + iounmap((void __iomem *)mem->va);
> +
> + for (i = 0; i < r5_core->tcm_bank_count; i++) {
> + pm_domain_id = r5_core->tcm_banks[i].pm_domain_id;
> + if (zynqmp_pm_release_node(pm_domain_id))
> + pr_warn("can't turn off TCM bank %d", pm_domain_id);
> + }
> +
> + return 0;
> +}
> +
> +/*
> + * tcm_mem_map
> + * @rproc: single R5 core's corresponding rproc instance
> + * @mem: mem entry to initialize the va and da fields of
> + *
> + * Given TCM bank entry, this callback will set device address for R5
> + * running on TCM and also setup virtual address for TCM bank
> + * remoteproc carveout.
> + *
> + * return 0 on success, otherwise non-zero value on failure
> + */
> +static int tcm_mem_map(struct rproc *rproc,
> + struct rproc_mem_entry *mem)
> +{
> + void __iomem *va;
> +
> + va = ioremap_wc(mem->dma, mem->len);
> + if (IS_ERR_OR_NULL(va))
> + return -ENOMEM;
> +
> + /* Update memory entry va */
> + mem->va = (void *)va;
> +
> + /* clear TCMs */
> + memset_io(va, 0, mem->len);
> +
> + /*
> + * The R5s expect their TCM banks to be at address 0x0 and 0x2000,
> + * while on the Linux side they are at 0xffexxxxx.
> + *
> + * Zero out the high 12 bits of the address. This will give
> + * expected values for TCM Banks 0A and 0B (0x0 and 0x20000).
> + */
> + mem->da &= 0x000fffff;
> +
> + /*
> + * TCM Banks 1A and 1B still have to be translated.
> + *
> + * Below handle these two banks' absolute addresses (0xffe90000 and
> + * 0xffeb0000) and convert to the expected relative addresses
> + * (0x0 and 0x20000).
> + */
> + if (mem->da == 0x90000 || mem->da == 0xB0000)
> + mem->da -= 0x90000;
> +
> + /* if translated TCM bank address is not valid report error */
> + if (mem->da != 0x0 && mem->da != 0x20000) {
> + dev_err(&rproc->dev, "invalid TCM address: %x\n", mem->da);
> + return -EINVAL;
> + }
> + return 0;
> +}
> +
> +static int add_tcm_carveout_split_mode(struct rproc *rproc)
> +{
> + int i, num_banks, ret;
> + struct rproc_mem_entry *mem;
> + enum pm_node_id pm_domain_id;
> + u32 bank_addr;
> + size_t bank_size = 0;
> + char *bank_name;
> + struct device *dev;
> + struct zynqmp_r5_core *r5_core;
> +
> + r5_core = (struct zynqmp_r5_core *)rproc->priv;
> + if (!r5_core)
> + return -EINVAL;
> +
> + dev = r5_core->dev;
> +
> + /* go through zynqmp banks for r5 node */
> + num_banks = r5_core->tcm_bank_count;
> + if (num_banks <= 0) {
> + dev_err(dev, "need to specify TCM banks\n");
> + return -EINVAL;
> + }
> +
> + for (i = 0; i < num_banks; i++) {
> + bank_addr = (u32)r5_core->tcm_banks[i].addr;
> + bank_name = r5_core->tcm_banks[i].bank_name;
> + bank_size = r5_core->tcm_banks[i].size;
> + pm_domain_id = r5_core->tcm_banks[i].pm_domain_id;
> +
> + ret = zynqmp_pm_request_node(pm_domain_id,
> + ZYNQMP_PM_CAPABILITY_ACCESS, 0,
> + ZYNQMP_PM_REQUEST_ACK_BLOCKING);
> + if (ret < 0) {
> + dev_err(dev, "failed to turn on TCM %d", pm_domain_id);
> + return ret;
> + }
> +
> + dev_dbg(dev, "TCM carveout split mode %s addr=%x, size=0x%lx",
> + bank_name, bank_addr, bank_size);
> +
> + /* add carveout */
> + mem = rproc_mem_entry_init(dev, NULL, bank_addr,
> + bank_size, bank_addr,
> + tcm_mem_map, tcm_mem_unmap,
> + bank_name);
> + if (IS_ERR_OR_NULL(mem)) {
> + /* Turn off all TCM banks turned on before */
> + do {
> + pm_domain_id = r5_core->tcm_banks[i].pm_domain_id;
> + ret = zynqmp_pm_release_node((u32)pm_domain_id);
> + if (ret)
> + dev_warn(dev,
> + "fail to release node: %x, %x\n",
> + (u32)pm_domain_id, ret);
> + } while (i--);
> + return -ENOMEM;
> + }
> +
> + rproc_add_carveout(rproc, mem);
> + }
> +
> + return 0;
> +}
> +
> +static int add_tcm_carveout_lockstep_mode(struct rproc *rproc)
> +{
> + int i, num_banks, ret;
> + struct rproc_mem_entry *mem;
> + enum pm_node_id pm_domain_id;
> + u32 bank_addr;
> + size_t bank_size = 0;
> + char *bank_name;
> + struct device *dev;
> + struct platform_device *parent_pdev;
> + struct zynqmp_r5_cluster *cluster;
> + struct zynqmp_r5_core *r5_core;
> +
> + r5_core = (struct zynqmp_r5_core *)rproc->priv;
> + if (!r5_core)
> + return -EINVAL;
> +
> + dev = r5_core->dev;
> + if (!dev) {
> + pr_err("r5 core device unavailable\n");
> + return -ENODEV;
> + }
> +
> + /* go through zynqmp banks for r5 node */
> + num_banks = r5_core->tcm_bank_count;
> + if (num_banks <= 0) {
> + dev_err(dev, "need to specify TCM banks\n");
> + return -EINVAL;
> + }
> +
> + bank_addr = (u32)r5_core->tcm_banks[0].addr;
> + bank_name = r5_core->tcm_banks[0].bank_name;
> + for (i = 0; i < num_banks; i++) {
> + bank_size += r5_core->tcm_banks[i].size;
> + pm_domain_id = r5_core->tcm_banks[i].pm_domain_id;
> +
> + ret = zynqmp_pm_request_node(pm_domain_id,
> + ZYNQMP_PM_CAPABILITY_ACCESS, 0,
> + ZYNQMP_PM_REQUEST_ACK_BLOCKING);
> + if (ret < 0) {
> + dev_err(dev, "failed to turn on TCM %d", pm_domain_id);
> + return ret;
> + }
> + }
> +
> + dev_dbg(dev, "TCM add carveout lockstep mode %s addr=0x%x, size=0x%lx",
> + bank_name, bank_addr, bank_size);
> +
> + /* add carveout */
> + mem = rproc_mem_entry_init(dev, NULL, bank_addr,
> + bank_size, bank_addr,
> + tcm_mem_map, tcm_mem_unmap,
> + bank_name);
> + if (IS_ERR_OR_NULL(mem)) {
> + for (i = 0; i < num_banks; i++) {
> + pm_domain_id = r5_core->tcm_banks[i].pm_domain_id;
> + ret = zynqmp_pm_release_node((u32)pm_domain_id);
> + if (ret)
> + dev_warn(dev,
> + "fail to release node: %x ret: %x\n",
> + (u32)pm_domain_id, ret);
> + }
> + return -ENOMEM;
> + }
> +
> + rproc_add_carveout(rproc, mem);
> +
> + return 0;
> +}
> +
> +/*
> + * add_tcm_banks()
> + * @rproc: single R5 core's corresponding rproc instance
> + *
> + * Given R5 node in remoteproc instance
> + * allocate remoteproc carveout for TCM memory
> + * needed for firmware to be loaded
> + *
> + * return 0 on success, otherwise non-zero value on failure
> + */
> +static int add_tcm_banks(struct rproc *rproc)
> +{
> + struct device *dev;
> + struct platform_device *parent_pdev;
> + struct zynqmp_r5_cluster *cluster;
> + struct zynqmp_r5_core *r5_core;
> +
> + r5_core = (struct zynqmp_r5_core *)rproc->priv;
> + if (!r5_core)
> + return -EINVAL;
> +
> + dev = r5_core->dev;
> + if (!dev) {
> + pr_err("r5 core device unavailable\n");
> + return -ENODEV;
> + }
> +
> + parent_pdev = to_platform_device(dev->parent);
> + if (!parent_pdev) {
> + dev_err(dev, "parent platform dev unavailable\n");
> + return -ENODEV;
> + }
> +
> + cluster = platform_get_drvdata(parent_pdev);
> + if (!cluster) {
> + dev_err(&parent_pdev->dev, "Invalid driver data\n");
> + return -EINVAL;
> + }
> +
> + if (cluster->mode == SPLIT_MODE)
> + return add_tcm_carveout_split_mode(rproc);
> + else if (cluster->mode == LOCKSTEP_MODE)
> + return add_tcm_carveout_lockstep_mode(rproc);
> +
> + dev_err(cluster->dev, "invalid cluster mode\n");
> + return -EINVAL;
> +}
> +
> +/*
> + * zynqmp_r5_parse_fw()
> + * @rproc: single R5 core's corresponding rproc instance
> + * @fw: ptr to firmware to be loaded onto r5 core
> + *
> + * When loading firmware, ensure the necessary carveouts are in remoteproc
> + *
> + * return 0 on success, otherwise non-zero value on failure
> + */
> +static int zynqmp_r5_parse_fw(struct rproc *rproc, const struct firmware *fw)
> +{
> + int ret;
> + struct zynqmp_r5_core *r5_core;
> + struct device *dev;
> +
> + r5_core = rproc->priv;
> + if (!r5_core) {
> + dev_err(&rproc->dev, "r5 core not available\n");
> + return -EINVAL;
> + }
> +
> + dev = r5_core->dev;
> +
> + ret = add_tcm_banks(rproc);
> + if (ret) {
> + dev_err(dev, "failed to get TCM banks, err %d\n", ret);
> + return ret;
> + }
> +
> + ret = add_mem_regions(rproc);
> + if (ret)
> + dev_warn(dev, "failed to get reserve mem regions %d\n", ret);
> +
> + ret = rproc_elf_load_rsc_table(rproc, fw);
> + if (ret == -EINVAL) {
> + /*
> + * resource table only required for IPC.
> + * if not present, this is not necessarily an error;
> + * for example, loading r5 hello world application
> + * so simply inform user and keep going.
> + */
> + dev_info(&rproc->dev, "no resource table found.\n");
> + ret = 0;
> + }
> + return ret;
> +}
> +
> +static struct rproc_ops zynqmp_r5_rproc_ops = {
> + .start = zynqmp_r5_rproc_start,
> + .stop = zynqmp_r5_rproc_stop,
> + .load = rproc_elf_load_segments,
> + .parse_fw = zynqmp_r5_parse_fw,
> + .find_loaded_rsc_table = rproc_elf_find_loaded_rsc_table,
> + .sanity_check = rproc_elf_sanity_check,
> + .get_boot_addr = rproc_elf_get_boot_addr,
> +};
> +
> +static void zynqmp_r5_print_dt_node_info(struct zynqmp_r5_cluster *cluster)
> +{
> + int i, j, k;
> + struct zynqmp_r5_core *r5_core;
> +
> + dev_dbg(cluster->dev, "Printing dt node info\n");
> +
> + pr_debug("cluster mode = %d\n", cluster->mode);
> + pr_debug("r5f cluster in %s mode\n", (cluster->mode == 0) ? "SPLIT" :
> + cluster->mode == 1 ? "LOCKSTEP" : "SINGLE_CPU");
> + pr_debug("r5f num cores = %d\n", cluster->core_count);
> +
> + for (i = 0; i < cluster->core_count; i++) {
> + r5_core = &cluster->r5_cores[i];
> + if (!r5_core) {
> + pr_err("can't get r5_core\n");
> + continue;
> + }
> +
> + pr_debug("r5 core %d nodes\n", i);
> + pr_debug("TCM banks = %d\n", r5_core->tcm_bank_count);
> + for (k = 0; k < r5_core->tcm_bank_count; k++) {
> + pr_debug("tcm %d addr=0x%llx size=0x%lx, pm_id=%d, %s\n",
> + k, r5_core->tcm_banks[k].addr,
> + r5_core->tcm_banks[k].size,
> + r5_core->tcm_banks[k].pm_domain_id,
> + r5_core->tcm_banks[k].bank_name);
> + }
> +
> + pr_debug("reserve mem regions = %d\n", r5_core->res_mem_count);
> +
> + for (j = 0; j < r5_core->res_mem_count; j++) {
> + pr_debug("mem %d addr=0x%llx, size=0x%llx, name=%s\n",
> + j, r5_core->res_mem[j].base,
> + r5_core->res_mem[j].size,
> + r5_core->res_mem[j].name);
> + }
> + }
> +}
> +
> +/**
> + * zynqmp_r5_add_rproc_core() - Probes ZynqMP R5 processor device node
> + * this is called for each individual R5 core to
> + * set up mailbox, Xilinx platform manager unique ID,
> + * add to rproc core
> + *
> + * @r5_core: zynqmp_r5_core r5 core object to initialize
> + *
> + * Return: 0 for success, negative value for failure.
> + */
> +static int zynqmp_r5_add_rproc_core(struct zynqmp_r5_core *r5_core)
> +{
> + int ret;
> + struct rproc *r5_rproc;
> + struct device *dev;
> +
> + dev = r5_core->dev;
> +
> + /* Set up DMA mask */
> + ret = dma_set_coherent_mask(dev, DMA_BIT_MASK(32));
> + if (ret)
> + return ret;
> +
> + /* Allocate remoteproc instance */
> + r5_rproc = devm_rproc_alloc(dev, dev_name(dev), &zynqmp_r5_rproc_ops,
> + NULL, sizeof(struct zynqmp_r5_core));
> + if (IS_ERR_OR_NULL(r5_rproc))
> + return -ENOMEM;
> +
> + r5_rproc->auto_boot = false;
> + r5_rproc->priv = r5_core;
> +
> + /* Add R5 remoteproc */
> + ret = devm_rproc_add(dev, r5_rproc);
> + if (ret) {
> + pr_err("failed to add r5 remoteproc\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int zynqmp_r5_get_tcm_node(struct zynqmp_r5_cluster *cluster)
> +{
> + int tcm_bank_count, tcm_node;
> + int i = 0, j;
> + struct zynqmp_r5_core *r5_core;
> + const struct mem_bank_data *tcm = zynqmp_tcm_banks;
> + struct device *dev = cluster->dev;
> +
> + /* ToDo: Use predefined TCM address space values from driver until
> + * system-dt spec is not final fot TCM
> + */
> + tcm_bank_count = ARRAY_SIZE(zynqmp_tcm_banks);
> +
> + /* count per core tcm banks */
> + tcm_bank_count = tcm_bank_count / cluster->core_count;
> +
> + /* r5 core 0 will use all of TCM banks in lockstep mode.
> + * In split mode, r5 core0 will use 128k and r5 core1 will use another
> + * 128k. Assign TCM banks to each core accordingly
> + */
> + tcm_node = 0;
> + for (j = 0; j < cluster->core_count; j++) {
> + r5_core = &cluster->r5_cores[j];
> + r5_core->tcm_banks = devm_kzalloc(dev, sizeof(struct mem_bank_data) *
> + tcm_bank_count, GFP_KERNEL);
> + if (IS_ERR_OR_NULL(r5_core->tcm_banks))
> + return -ENOMEM;
> +
> + for (i = 0; i < tcm_bank_count; i++) {
> + /* Use pre-defined TCM reg values.
> + * Eventually this should be replaced by values
> + * parsed from dts.
> + */
> + r5_core->tcm_banks[i].addr = tcm[tcm_node].addr;
> + r5_core->tcm_banks[i].size = tcm[tcm_node].size;
> + r5_core->tcm_banks[i].pm_domain_id = tcm[tcm_node].pm_domain_id;
> + r5_core->tcm_banks[i].bank_name = tcm[tcm_node].bank_name;
> + tcm_node++;
> + }
> +
> + r5_core->tcm_bank_count = tcm_bank_count;
> + }
> +
> + return 0;
> +}
> +
> +static int zynqmp_r5_get_mem_region_node(struct zynqmp_r5_core *r5_core)
> +{
> + int res_mem_count, i;
> + struct device *dev;
> + struct device_node *np, *rmem_np;
> + struct reserved_mem *rmem;
> +
> + dev = r5_core->dev;
> +
> + np = r5_core->np;
> + if (IS_ERR_OR_NULL(np)) {
> + pr_err("invalid device node of r5 core\n");
> + return -EINVAL;
> + }
> +
> + res_mem_count = of_property_count_elems_of_size(np, "memory-region",
> + sizeof(phandle));
> + if (res_mem_count <= 0) {
> + dev_warn(dev, "failed to get memory-region property %d\n",
> + res_mem_count);
> + return -EINVAL;
> + }
> +
> + r5_core->res_mem = devm_kzalloc(dev,
> + res_mem_count * sizeof(struct reserved_mem),
> + GFP_KERNEL);
> + if (!r5_core->res_mem) {
> + dev_err(dev, "failed to allocate mem region memory\n");
> + return -ENOMEM;
> + }
> +
> + for (i = 0; i < res_mem_count; i++) {
> + rmem_np = of_parse_phandle(np, "memory-region", i);
> + if (!rmem_np)
> + return -EINVAL;
> +
> + rmem = of_reserved_mem_lookup(rmem_np);
> + if (!rmem) {
> + of_node_put(rmem_np);
> + return -EINVAL;
> + }
> +
> + memcpy(&r5_core->res_mem[i], rmem,
> + sizeof(struct reserved_mem));
> + of_node_put(rmem_np);
> + }
> +
> + r5_core->res_mem_count = res_mem_count;
> +
> + return 0;
> +}
> +
> +static int zynqmp_r5_core_init(struct zynqmp_r5_cluster *cluster)
> +{
> + int ret, i;
> + struct zynqmp_r5_core *r5_core;
> + struct device *dev = cluster->dev;
> +
> + ret = zynqmp_r5_get_tcm_node(cluster);
> + if (ret < 0) {
> + dev_err(dev, "can't get tcm node, err %d\n", ret);
> + return ret;
> + }
> +
> + for (i = 0; i < cluster->core_count; i++) {
> + r5_core = &cluster->r5_cores[i];
> + if (!r5_core) {
> + pr_err("invalid r5 core\n");
> + return -EINVAL;
> + }
> +
> + ret = zynqmp_r5_get_mem_region_node(r5_core);
> + if (ret)
> + dev_warn(dev, "memory-region prop failed %d\n", ret);
> +
> + ret = of_property_read_u32_index(r5_core->np, "power-domains",
> + 1, &r5_core->pm_domain_id);
> + if (ret) {
> + dev_err(dev, "failed to get power-domains property\n");
> + return ret;
> + }
> +
> + ret = zynqmp_r5_set_mode(r5_core, cluster->mode);
> + if (ret)
> + return ret;
> +
> + ret = zynqmp_r5_add_rproc_core(r5_core);
> + if (ret) {
> + dev_err(dev, "failed to init r5 core %d\n", i);
> + return ret;
> + }
> + }
> +
> + return 0;
> +}
> +
> +static int zynqmp_r5_cluster_init(struct zynqmp_r5_cluster *cluster)
> +{
> + struct device *dev = cluster->dev;
> + struct device_node *dev_node = dev_of_node(dev);
> + struct device_node *child;
> + struct platform_device *child_pdev;
> + int core_count = 0, ret, i;
> + enum zynqmp_r5_cluster_mode cluster_mode = LOCKSTEP_MODE;
> + struct zynqmp_r5_core *r5_cores;
> +
> + ret = of_property_read_u32(dev_node, "xlnx,cluster-mode", &cluster_mode);
> +
> + /* on success returns 0, if not defined then returns -EINVAL,
> + * In that case, default is LOCKSTEP mode
> + */
> + if (ret != -EINVAL && ret != 0) {
> + dev_err(dev, "Invalid xlnx,cluster-mode property\n");
> + return -EINVAL;
> + }
> +
> + if (cluster_mode == SINGLE_CPU_MODE) {
> + dev_err(dev, "driver does not support single cpu mode\n");
> + return -EINVAL;
> + } else if ((cluster_mode != SPLIT_MODE &&
> + cluster_mode != LOCKSTEP_MODE)) {
> + dev_err(dev, "Invalid cluster mode\n");
> + return -EINVAL;
> + }
> +
> + core_count = of_get_available_child_count(dev_node);
> + if (core_count <= 0) {
> + dev_err(dev, "Invalid number of r5 cores %d", core_count);
> + return -EINVAL;
> + } else if (cluster_mode == SPLIT_MODE && core_count != 2) {
> + dev_err(dev, "Invalid number of r5 cores for split mode\n");
> + return -EINVAL;
> + } else if (cluster_mode == LOCKSTEP_MODE && core_count == 2) {
> + dev_warn(dev, "Only r5 core0 will be used\n");
> + core_count = 1;
> + }
> +
> + r5_cores = devm_kzalloc(dev, sizeof(struct zynqmp_r5_core) *
> + core_count, GFP_KERNEL);
> + if (IS_ERR_OR_NULL(r5_cores)) {
> + dev_err(dev, "can't allocate memory for cores\n");
> + return -ENOMEM;
> + }
> +
> + i = 0;
> + for_each_available_child_of_node(dev_node, child) {
> + child_pdev = of_find_device_by_node(child);
> + if (!child_pdev)
> + return -ENODEV;
> +
> + r5_cores[i].dev = &child_pdev->dev;
> + if (!r5_cores[i].dev) {
> + pr_err("can't get device for r5 core %d\n", i);
> + return -ENODEV;
> + }
> +
> + r5_cores[i].np = dev_of_node(r5_cores[i].dev);
> + if (!r5_cores[i].np) {
> + pr_err("can't get device node for r5 core %d\n", i);
> + return -ENODEV;
> + }
> +
> + i++;
> + if (i == core_count)
> + break;
> + }
> +
> + cluster->mode = cluster_mode;
> + cluster->core_count = core_count;
> + cluster->r5_cores = r5_cores;
> +
> + ret = zynqmp_r5_core_init(cluster);
> + if (ret < 0) {
> + dev_err(dev, "failed to init r5 core err %d\n", ret);
> + return ret;
> + }
> +
> + zynqmp_r5_print_dt_node_info(cluster);
> +
> + return 0;
> +}
> +
> +static void zynqmp_r5_cluster_exit(void *data)
> +{
> + struct platform_device *pdev = (struct platform_device *)data;
> +
> + platform_set_drvdata(pdev, NULL);
> +
> + pr_info("Exit r5f subsystem driver\n");
> +}
> +
> +/*
> + * zynqmp_r5_remoteproc_probe()
> + *
> + * @pdev: domain platform device for R5 cluster
> + *
> + * called when driver is probed, for each R5 core specified in DT,
> + * setup as needed to do remoteproc-related operations
> + *
> + * Return: 0 for success, negative value for failure.
> + */
> +static int zynqmp_r5_remoteproc_probe(struct platform_device *pdev)
> +{
> + int ret;
> + struct zynqmp_r5_cluster *cluster;
> + struct device *dev = &pdev->dev;
> +
> + cluster = devm_kzalloc(dev, sizeof(*cluster), GFP_KERNEL);
> + if (IS_ERR_OR_NULL(cluster))
> + return -ENOMEM;
> +
> + cluster->dev = dev;
> +
> + ret = devm_of_platform_populate(dev);
> + if (ret) {
> + dev_err(dev, "failed to populate platform dev %d\n", ret);
> + return ret;
> + }
> +
> + /* wire in so each core can be cleaned up at driver remove */
> + platform_set_drvdata(pdev, cluster);
> +
> + ret = devm_add_action_or_reset(dev, zynqmp_r5_cluster_exit, pdev);
> + if (ret)
> + return ret;
> +
> + ret = zynqmp_r5_cluster_init(cluster);
> + if (ret) {
> + dev_err(dev, "Invalid r5f subsystem device tree\n");
> + return ret;
> + }
> +
> + dev_info(dev, "Xilinx r5f remoteproc driver probe success\n");
> + return 0;
> +}
> +
> +/* Match table for OF platform binding */
> +static const struct of_device_id zynqmp_r5_remoteproc_match[] = {
> + { .compatible = "xlnx,zynqmp-r5fss", },
> + { /* end of list */ },
> +};
> +MODULE_DEVICE_TABLE(of, zynqmp_r5_remoteproc_match);
> +
> +static struct platform_driver zynqmp_r5_remoteproc_driver = {
> + .probe = zynqmp_r5_remoteproc_probe,
> + .driver = {
> + .name = "zynqmp_r5_remoteproc",
> + .of_match_table = zynqmp_r5_remoteproc_match,
> + },
> +};
> +module_platform_driver(zynqmp_r5_remoteproc_driver);
> +
> +MODULE_DESCRIPTION("Xilinx R5F remote processor driver");
> +MODULE_AUTHOR("Xilinx Inc.");
> +MODULE_LICENSE("GPL v2");
> --
> 2.25.1
>
